Kinesis JSB Bedienungsanleitung

Kinesis®JSB™

USB foot switch family

(joystick button emulation)

USER’S MANUAL

Kinesis®JSB™USB foot switch family

(joystick button emulation)

For any USB system capable of providing generic HID joystick drivers for USB joysticks

Models covered:

FSMJ2-JSB: control module only, with two input jacks

FSMJ4-JSB: control module only, with four input jacks

FS12J-JSB: control module with two input jacks, one pedal

FS22A-JSB: dual angled pedals mounted on steel base

FS22AJ-JSB: dual angled pedals mounted on steel base with one jack for optional input device

FS32A-JSB: triple angled & adjustable pedals, mounted on steel base

FS32AJ-JSB: triple angled & adjustable pedals, mounted on steel base. Jack for optional input

Optional input accessories

FS007mp: single foot pedal with mini-phono plug

FS002HT8: Hand trigger, 8 foot cable with mini-phono plug.

*Waterproof (IPX8) models are available by special order.

September 2014Edition

website is located at www.kinesis.com.KINESIS is a registered trademark of Kinesis Corporation. JSB is a trademark of Kinesis

Corporation. Information in this document is subject to change without notice. No part of this document may be reproduced or

transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of

Kinesis Corporation.

Cover: Triple pedal model shown (FS32A-JSB)

REGULATORY APPROVALS

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation.This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected

Consult the dealer or an experienced radio/TV technician for help

Warning

To assure continued FCC compliance, the user must use only shielded interfacing cables when connecting to

computer or peripheral. Also, any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

INDUSTRY CANADA COMPLIANCE STATEMENT

This Class B digital apparatus meets all requirements of the Canadian Interface-causing Equipment Regulations. Cet

Appareil numerique de la classe B respecte toutes les exiginces du Reglement sur le material broilleur du Canada.

CE COMPLIANCE FOR EMISSIONS AND IMMUNITY

This device has been tested to comply with the following European standards for emissions and immunity for ITE and

medical equipment: En 55022, En 55024, EN 61000-3-2/3, and EN 60601-1-2.

MEDICAL PRODUCT SAFETY

CONFORMS TO UL STD 60601-1; CERTIFIED TO CSA STD C22.2 NO. 601.1

4007055

The ETL Recognized Component mark on the product label indicates compliance with UL 60601-1 and CSA Std

C22.2 No. 601.1 standards for medical use. These products must be used with a UL listed computer to comply with

UL safety standards. The label will also indicate IPX1 per UL and CE standards for “drip-proof” water resistance.

Custom, non-programmable waterproof (IPX8) models are also available by special order. This product should not be

used in the presence of a flammable atmosphere such as an anesthetic mixture with air, oxygen, or nitrous oxide.

TABLE OF CONTENTS

Repetitive strain safety warning .................................................... 6

Features and compatibility ............................................................ 7

Installation ..................................................................................... 9

Operating & maintenance guidelines .............................................9

Trouble shooting, technical support .............................................10

Warranty ...................................................................................... 11

REPETITIVE STRAIN SAFETY WARNING

Continuous use of any computer input device may cause aches and pains or a more serious

cumulative trauma disorder (CTD) such as tendinitis.

#Observe sensible guidelines when using any computer input device to help

minimize the possibility of injury.

#Follow established guidelines for computer and workstation setup.

#Exercise good judgment in placing reasonable limits on your computer

usage time every day.

#Ensure that you take reasonable rest breaks from computer use during the

course of the day.

#At the first sign of stress-related injury (aching, numbness, or tingling

of an extremity), consult your health care professional.

Kinesis Corporation bases its product designs on research, proven features, and user

evaluations. However, because of the complex set of factors believed to contribute to

computer-related injuries, the company can make no warranty that any of its products will

prevent or cure any physical ailment.

Your risk of injury may be affected by workstation and chair design, posture, time worked

without breaks, type of work, activities outside of the workplace, and individual physiology.

FEATURES AND COMPATIBILITY

Overview

Kinesis JSB USB footswitches are designed to emulate joystick buttom

operations using generic drivers provided by the operating system. In general,

they will operate on any computer with an active USB port.

Up to four pedals are provided to perform joystick buttons 1-4. If jacks are

provided, only a Kinesis-supplied device (foot pedal or hand trigger) may be

connected. The pedals are connected to the appropriate pair of the four ports

provided by the small USB control module.

System compatibility

Generic drivers from the operating system are used by all systems to operate the

device. No special drivers are needed.

Detailed features

The pedals produce joystick button actions 1 and 2, or 1, 2, and 3, or 1 through 4,

depending on whether you have a model with 2, 3, or 4 inputs.

Status LEDs

On the front of the electronics enclosure (facing the user) are two light emitting

diodes (LEDs) which indicate the status of the device. When the green LED is

illuminated steadily, the unit is operating correctly. The red LED blinks on every

pedal press If the red LED is on continuously, the device is not working correctly

(see the chapter on “Troubleshooting and Technical Support”).

Optional accessories

Hand triggers, extra pedals, and extension cables for jack-equipped models are

available from Kinesis. Use only Kinesis accessories with this product. For more

information or to order, contact Kinesis via email ([email protected]) or phone

(800-454-6374) between the hours of 8am and 5pm Pacific Time.

INSTALLATION

Connecting to your computer

The Kinesis JSB™ Foot Switch may be connected to any USB port. The first

time this is done, it is best to connect it after your computer has booted up and is

logged in (if you have a network) so that you can see the “new device detected”

message.

Drivers (Windows 2000 through Windows 7)

The device installs itself automatically as a generic HID device on all recent

versions of Windows without requiring user-supplied drivers. Once the required

generic driver is installed, the JSB foot switch connects like a standard USB

joystick. Just plug the cable into a USB port on your computer, whether the

computer is running or not.

OPERATING AND MAINTENANCE GUIDELINES

Flammable gases

The JSB foot switch is not designed to be used in an environment with

flammable or explosive gases, such as an anesthetic mixture with air, oxygen, or

nitrous oxide.

Duty cycle

The JSB footswitch is rated for continuous operation, though the computer or

operating system may affect how the device performs under such conditions.

Normal usage consists of intermittent pressing of the pedal to initiate a joystick

button action.

Cleaning

Occasional cleaning is recommended by first disconnecting the control module

from the computer, then wiping the pedals and electronics enclosure with a damp

cloth. Alternatively, a cloth dampened with rubbing alcohol (70% isopropanol)

may be used though any silk-screened graphics on the electronics enclosure may

be damaged over time by solvent effects. Do not immerse or allow liquid to

penetrate the interior of the control module or foot pedal. This product is not

designed to be sterilized or to be used in a sterile environment.

TROUBLESHOOTING AND TECHNICAL SUPPORT

Status lights

If a problem is suspected, the first place to check is the status lights. If the green

LED displays a steady light, the unit is operating normally. If there is no LED

illuminated the unit is not powered. If the green LED is flashing, or if the red

LED is illuminated continuously, the unit is not ready and requires attention. It is

normal for the red LED to flash briefly every time a pedal is depressed.

Contacting Kinesis Technical Support

Contact Kinesis technical support only after you have read the entire User’s

Manual and still have problems or unanswered questions. You may contact

Kinesis Technical Support by E-mail ([email protected]), fax (425-402-8181),

or phone (800-454-6374 or 425-402-8100). Technical support hours are 8:30am

to 4:30pm Pacific time except weekends and holidays.

When you contact Kinesis, be prepared to document your purchase date, as well

as your product model number and serial number. Also know the brand and

model of your computer and your computer’s operating system.

Repairs by authorized repair centers only

This product should be repaired by authorized, qualified personnel only.

Unauthorized or inexpertly carried-out repairs may seriously jeopardize the

safety of the user (such as from fire danger) and may invalidate your warranty.

See Operating and Maintenance Guidelines.

Getting an RMA number prior to product repair

For any repair, whether or not it is covered by your warranty, you must contact

Kinesis to explain the problem, provide certain information, and get an RMA

number to write on your package. Packages sent to Kinesis without first

obtaining an RMA number may be refused, and the product will not be repaired

without information and instructions from the owner.

Packaging and Shipping

If you need to ship the Product, use its original or other packaging that protects it

against impact and shock. Be sure to contact Kinesis for an RMA number and

Kinesis’ shipping address. You should insure the package since Kinesis is not

responsible for items until they are received by the Kinesis repair center.

Inhaltsverzeichnis

Andere Kinesis Schalten Handbücher

Kinesis

Kinesis FS007RJ11 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung