KING PHOENIX KPD1000 Bedienungsanleitung

KPD1000 (DISH) • KPT1000 (DIRECTV)

Owner’s Manual

CONTENTS

INSTALLATION MATERIALS SUPPLIED BY INSTALLER ....................2

ANTENNA UNIT ASSEMBLY ......................................... 2-6

UNPACK AND VERIFY COMPONENTS ................................2

RAISE ARM FOR DISH INSTALLATION ................................3

ATTACH DISH AND ARM TO BASE MOUNT.............................4

DISH: LNB INSTALLATION ........................................ 5-6

DIRECTV: LNB INSTALLATION ..................................... 5-6

CONNECT LED LIGHT (OPTIONAL) ...................................6

INSTALLATION ................................................... 7-15

DETERMINE ROOF LOCATION ......................................8

MOUNT THE UNIT .................................................9

MOUNT THE STOW PLATE..........................................9

ROUTE WIRING............................................... 10-11

MAKE INTERIOR CONNECTIONS ................................ 12-15

OPERATION .................................................... 16-18

MOVING THE DISH MANUALLY .......................................19

KING LIMITED WARRANTY ...........................................20

FCC GUIDELINES...................................................21

This Owner’s Manual contains detailed installation and operating instructions.

If the KING Phoenix is already installed,

see the Quick Reference Guide to start using your KING Phoenix right away.

Page 2

ANTENNA UNIT ASSEMBLY

UNPACK AND VERIFY COMPONENTS

1. The KING Phoenix was shipped in two boxes. Open the boxes and verify all parts are present.

BOX 1

BOX 2 (Box will be labeled for DISH or DIRECTV)

• Junction box

• Stow plate

• Clam shell

• Assembly and installation hardware

• Scotch-Lok connectors (2)

• Base mount assembly

• Power supply, 12VDC, 7 amp

• Control cable (30’)

• Coax cable (35’)

• Owner’s manual

• Quick reference guide

• Reector dish

• Controller

• Arm assembly with (2) stow brackets

• LNB

INSTALLATION MATERIALS SUPPLIED BY INSTALLER

The installer is responsible for determining the most appropriate fasteners to secure the antenna unit to

the roof. Depending on the roof material, fasteners such as lag screws, well nuts, sheet metal screws,

toggle bolts and T anchors may be used, and should always be used with a roof-compatible sealant.

IMPORTANT! The installer is responsible for weatherproong all holes with sealant.

• Drill and drill bit set (You will need a bit to drill a 1 inch hole in the roof for cable entry, and

any necessary bits for your choice of roof fasteners).

• #2 Phillips screwdriver

• #3 Phillips screwdriver

• Wire cutters

• Pliers (for crimping Scotch-Lok connectors)

• Roof-compatible sealant

• Dielectric grease

• Appropriate tools and fasteners to install all components and wiring

• Please read this Owner’s Manual thoroughly before installing and using the KING Phoenix.

• Keep this Owner’s Manual and the included Quick Reference Guide in a safe place for future

reference.

• Follow all instructions and warnings. Set up and operate the KING Phoenix in accordance with

the instructions.

Do not power wash the KING Phoenix.

Thank you for choosing the KING Phoenix

automatic roof-mounted satellite TV antenna system!

Page 3

RAISE DISH ARM TO INSTALL DISH ASSEMBLY

1. Place the base mount on a stable and level work surface.

2. Make connections as shown below.

CONTROL CABLE CONNECTION

12 VDC To LNB

To REC

110 VAC

Back of Controller

Controller Cable

Base Mount

Included Power Supply

KC1421

CONTROL CABLE CONNECTION

12 VDC To LNB

To REC

110 VAC

Back of Controller

Controller Cable

Base Mount

Included Power Supply

KC1421

You can do the assembly steps on pages 3-6 on the ground or on the roof.

You may nd it easier to take the components up to the roof before assembly.

TIP

3. Raise the dish arm to the position shown above as follows:

A. Press POWER to turn on controller.

B. Press POWER again to enter menu.

C. Use up arrow button to go to menu item 3: MOVE ELEVATION.

E. Press and hold up arrow to raise dish arm to position shown.

F. Press and hold POWER to turn o󰀨 controller. Disconnect components.

D. Press POWER to select item 3.

SEARCH STOW Satellite Antenna Controller SELECT

FLASH

LNB

POWER

KC1404

SEARCH STOW Satellite Antenna Controller SELECT

FLASH

LNB

POWER

KC1404

A BC DE F

Page 4

ATTACH DISH AND ARM TO BASE MOUNT

1. Feed coax (inside the split loom) thru the hole in the dish, from back to front.

2. Attach the dish to the mounting brackets on the base mount using the top two holes and supplied

washers and screws (1/4”-20 x 3/4” Phillips). Finger tighten only.

3. Attach the LNB arm to the dish using the supplied washers and screws (1/4”-20 x 3/4” Phillips).

Finger tighten only.

4. When all six screws are properly inserted and LNB arm rotates upward (not downward) tighten

all six screws (#3 Phillips screwdriver).

When properly oriented, the LNB arm should rotate upward towards the dish, not downward.

TIP

Attach dish to base mount

Attach LNB arm to dish

When properly installed,

arm rotates up

KC1400

(2) 1/4-20 x 3/4” Screws

(2) 1/4” Washers

(4) 1/4-20 x 3/4” Screws

(4) 1/4” Washers

Attach dish to base mount

Attach LNB arm to dish

When properly installed,

arm rotates up

KC1400

(2) 1/4-20 x 3/4” Screws

(2) 1/4” Washers

(4) 1/4-20 x 3/4” Screws

(4) 1/4” Washers

Page 5

1. Remove and save (2) inner screws from

LNB bracket.

2. Loosen, but do not remove, (2) outer

screws on LNB bracket.

3. Slide (2) brackets into position and fasten

to arm with (2) screws.

DIRECTV: LNB INSTALLATION

4. Insert LNB into bracket.

5. Replace (2) inner screws thru the LNB.

Tighten all (4) screws.

Loosen (2) outer screws

Slide (2) brackets

into position

Fasten (2) brackets

with supplied screws

(#3 Phillips)

Remove and save

(2) inner screws

KC1417

Loosen (2) outer screws

Slide (2) brackets

into position

Fasten (2) brackets

with supplied screws

(#3 Phillips)

Remove and save

(2) inner screws

KC1417

Replace (2) inner screws

Tighten (4) screws

Insert LNB

KC1418

Replace (2) inner screws

Tighten (4) screws

Insert LNB

KC1418

1. Fasten (2) stow brackets to arm brackets

with (2) screws on each side.

2. Capture crossbar with attached LNB and

fasten with (1) screw on each side.

DISH: LNB INSTALLATION

Arm

Bracket

Stow Bracket

#3 Phillips

Page 6

BOTH DISH & DIRECTV:

1. Route coax along TOP of arm to LNB.

2. Fill coax connector with dielectric grease. Connect to LEFT LNB port.

Fill coax connector with dielectric grease to prevent corrosion.

Coax connection should be snug only. Do not over-tighten.

Left Side

KC1415

Left Side

KC1415

KC1422KC1422

Fasten loom to arm

with cable ties

Leave enough slack in loom to prevent

binding when arm pivots up against dish

KC1423

Insert wires completely.

Crimp with pliers. Fasten loom to arm

with cable ties

Leave enough slack in loom to prevent

binding when arm pivots up against dish

KC1423

Insert wires completely.

Crimp with pliers.

CONNECT LED LIGHTS (OPTIONAL)

2. Splice wires from loom to LED wires, using the included Scotch-Lok connectors (black to black

and red to red).

1. Cut o󰀨 excess LED wire length.

3. Route the loom down either side of the LNB arm and secure with provided cable ties. Bundle

any excess wire length to arm with cable ties.

4. Tuck any excess loom back thru the dish. Leave enough loom out to prevent binding when

raising the LNB arm up against the dish.

5. Lift LNB arm to make sure there is no stress on the loom as the arm is lifted up against dish.

The LEDs illuminate the dish at night, and are always on when there is power

to the controller. If you don’t wish to connect the LEDs, properly terminate and

secure the wires as they are “live” (12VDC present at all times).

Page 7

INSTALLATION

Edge of vehicle

Front of Vehicle

Rear of Vehicle

TYPICAL

INSTALLATION

TOP VIEW

Secure to roof

every 12”-18”

Service loop

in wiring

Clam

Shell

Junction Box

Stow Plate

Stowed position

Edge of vehicle

Front of Vehicle

Rear of Vehicle

TYPICAL

INSTALLATION

TOP VIEW

Secure to roof

every 12”-18”

Service loop

in wiring

Clam

Shell

Junction Box

Stow Plate

Stowed position

DETERMINE ROOF LOCATION ......................8

MOUNT THE UNIT ................................9

MOUNT THE STOW PLATE .........................9

ROUTE WIRING ...............................10-11

MAKE INTERIOR CONNECTIONS................ 12-15

When stowed, the dish must point toward the back of the vehicle.

Page 8

Roof cross beams

KC1389

Roof cross beams

Front of

Vehicle

Roof cross beams

KC1389

Roof cross beams

Front of

Vehicle

KC1387KC1387

Front of

Vehicle

Overhead view with dish lowered

KC1396

Front of

Vehicle

Overhead view with dish lowered

KC1396

The unit should be no more than

3 degrees from level.

Rotational clearance from

center rotation point is 26” when

dish is elevated and rotating.

This is a safety zone. Anything

higher than 6” within this zone

is at risk.

When lowered, the dish must

face the rear of the vehicle to

avoid damage to unit while

vehicle is in motion.

37”

26” R

33.5”

The installation area must be clean to ensure good sealing to the roof.

Identify interior location for controller and ensure the 30’ cable will reach between the

controller and the antenna unit.

At least two mounting feet should be

over roof support beams.

Fasteners from at least two mounting

feet should penetrate the roof beams,

ideally toward the front of the vehicle.

Make sure mounting screws will not damage any interior roof wiring or tubing when installed.

DETERMINE ROOF LOCATION

1. Determine the mounting location based on the following:

All of the following points are important.

Page 9

SEALANT

KC1397 SEALANT

KC1397

KC1424

Stow

Plate

KC1424

Stow

Plate

MOUNT THE UNIT

MOUNT THE STOW PLATE

1. Loosen foot nuts. Rotate feet into mounting position

(they should look like illustration at right). Re-tighten

foot nuts.

4. Mount the unit using foot mounting holes and any additional mounting holes you drilled.

2. If the fasteners you have chosen require pilot holes, place

the unit in its location and use the foot holes to mark the

pilot hole locations. Drill pilot holes.

3. Apply roof-compatible sealant to roof around entire area where fasteners will penetrate the roof.

5. Seal all fastener heads and foot perimeter with roof-compatible sealant.

1. Apply roof-compatible sealant

around perimeter of stow plate.

Make an “X” with sealant in the

middle.

2. Press stow plate rmly into place.

Take all necessary safety precautions

when lifting the unit up to the roof.

The stow plate mounts 16” in

front of the base mount body.

Depending on your roof, you may wish to use fasteners in combination with the sealant.

The installer is responsible for determining the best fasteners, and for waterproong all holes

and sealing all fastener heads.

In the event your fasteners do not align with roof beams, it is highly recommended you

drill extra holes in the mounting feet for additional mounting strength.

TIP

KC1403KC1403

Roof-compatible sealant.

16”

Page 10

4. Make a service loop in the wiring and run it to where it will enter the vehicle.

1. Run control cable and coax from antenna unit to junction box location.

3. Place wiring connections inside the junction box and install junction box to roof. Seal properly.

7. Screw clam shell cover over hole. Seal properly.

8. Secure wiring to roof every 12”-18.” Seal properly.

5. Drill a 1 inch hole in the roof where the cabling will enter vehicle.

6. Feed wiring thru hole into vehicle interior. Seal hole properly.

2. Fill coax connector with grease. Connect antenna unit coax to roof coax. Plug in control cables.

Step 5: When drilling thru roof, proceed slowly, making

sure no cables or critical components will be damaged.

Step 3: Fully seal screw holes and seal around junction box.

Steps 6 and 7: Fully seal wiring hole.

Fully seal screw holes and around clam shell cover.

Step 8: Fully seal all wiring clamps and screws.

Step 2: Fill coax connector with dielectric grease to prevent corrosion.

Do not over-tighten coax connector.

ROUTE WIRING (Steps 1-8 use illustration on next page.)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KING Antenne Handbücher

KING

KING QUEST VQ4200 Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING QUEST VQ4100 Bedienungsanleitung

KING

KING DISH Tailgater Pro DTP4900 Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING DISH Tailgater VQ4400 Bedienungsanleitung

KING

KING QUEST PRO VQ4800 Bedienungsanleitung

KING

KING OA1000-OE Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING OA8200 WHITE Bedienungsanleitung

KING

KING QUEST VQ4200 Bedienungsanleitung

KING

KING OMNI GO OA1501 Bedienerhandbuch

KING

KING DISH Tailgater Pro VQ4900 Bedienungsanleitung

KING

KING DISH Tailgater DT4400 Bedienungsanleitung

KING

KING JACK OA8201 Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING ONEPRO KOP4800 Bedienungsanleitung

KING

KING Tailgater VQ4500 Bedienungsanleitung

KING

KING Jack OA8400 Bedienungsanleitung

KING

KING Falcon KF1000 Bedienungsanleitung

KING

KING One Pro KOP4800 Bedienungsanleitung

KING

KING Tailgater VQ4500 Bedienungsanleitung

KING

KING Dome KD3000 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch