KitchenAid KDIX 8810 Bedienungsanleitung

KDIX 8810

Installation instructions

Dishwasher safety 4

Installation requirements 5

Installation instructions 7

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

DANGER You can be killed or seriously injured if you don't immediately follow these

instructions.

WARNING You can be killed or seriously injured if you don't follow these instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what can happen if these instructions are not followed.

Dishwasher safety

• This dishwasher is manufactured for indoor use only.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service technician. The dishwasher must be installed to

meet all electrical and plumping national and local codes and ordinances.

Installation requirements

557 mm

total depth

525 mm

between clamp rails

Location Requirements

Protect the dishwasher and water lines leading to

the dishwasher against freezing. Damage caused by

freezing is not covered by the warranty.

If the dishwasher will be left unused for a period of

time, or in a location where it may be subject to

freezing, we recommend having it ‘winterised’ by

PRODUCT DIMENSIONS

our authorised service personnel. Please contact

our Customer Care Centre.

The dishwasher is shipped ready for installation of

a one hole tap unit. If a two, three, or four hole tap

unit is to be installed, the holes must be cut by a

qualified plumber, according to the Tap unit

manufacturer’s specifications.

3-prong ground type power supply cord - 1045 mm.

CABINET REQUIREMENTS

*NOTE: The coutout must be accurately cut to the dimensions shown within

1,6 mm. Dishwasher top flange overlaps the countertop cutout by 11 mm on

front and back edges and 6,4 mm on sides.

• Cabinetry and countertop must be sturdy enough to support loaded

dishwasher and sink (180 kg).

Radius: 57 mm

Radius: 25 mm

the right back corner must be

cut to this radius

Back right corner: If countertop is

more than 19 mm thick, measure

down 19 mm and cut 45° bevel all the

way around radius.

CRITICAL

RADIUS

11 mm min.

flat surface required

537 mm

(see *NOTE)

For base cabinet

installations, min. 914 mm

width required

864 mm

(see *NOTE)

537 mm

(see *NOTE)

It is recommended that sink

water and drain line

connections be located on

this side of cabinet

It is recommended

that dishwasher

water and drain line

connections be

located on this side

of cabinet

635 mm

deep countertop.

Countertop must

be level

Backsplash

531 mm

561 mm

504 mm

to centre of

check valve

254 mm

dishwasher drain

877 mm

total width

275 mm

to centre

of hole

tap unit

500 mm

maximum

opened

lid height

209 mm

height of sink

166 mm

centre

sink drain

856 mm

between

clamp rails

357 mm

centre of

tub drain

Factory

istalled

air gaps

GFCI

(TEST button)

32 mm

19 mm

44 mm

to centre of

hole tap unit

Separate drain trap for the sink and dishwasher

must be provided.

Dishwasher drain:

If the dishwasher drain exits through the back wall,

the centreline of the drain pipe must be a minimum

of 15 mm below the drain trap outlet. Drain pipe

must go down on its whole length. This is required

to completely drain the dishwasher tub so that no

standing water remains in tub. Connection

between dishwasher drain and drain pipe must be

done by pipe with diameter minimum ø 50 mm.

WATER SUPPLY REQUIREMENTS

For dishwasher:

Hot water line with 0.3-10 bar water pressure.

49°C (120°F) water at dishwasher.

For sink tap unit:

• Hot and cold water lines.

ELECTRICAL REQUIREMENTS

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instuctions can result in

death, fire, or electrical shock.

• If codes permit and a separate ground wire is

used, it is recommended that a qualified

electrician determine that the ground path is

adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not

sure the dishwasher is properly grounded.

• Do not have a fuse in the neutral or ground

circuit.

Garbage Disposer

If you plan to install a garbage disposer, an

additional separate electrical supply is required.

Recommended ground method

For your personal safety, this appliance must be

grounded. This appliance is equipped with a power

supply cord having a 3 prong ground plug. To

minimise possible shock hazard, the cord must be

plugged into a mating 3 prong ground-type outlet,

grounded in accordance with local codes and

ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to

have a properly grounded 3 prong outlet installed

by a qualified electrician.

Installation requirements

water- pipe

network

back

wall

15 mm

561 mm

Installation instructions

PREPARE DISHWASHER

1. With a utility knife, cut along the back right

corner of inner carton.

2. Remove inner carton. Leave dishwasher on

bottom pad.

3. Install tap unit (not included). The dishwasher is

shipped ready for installation of a one-hole tap

unit. If a two-, three-, four-hole faucet is to be

installed, the holes must be cut by a qualified

plumber according to the tap unit

manufacturer’s specifications.

INSTALL DISHWASHER

1. Mark countertop and apply a 6÷7 mm bead of

silicone caulk 6÷7 mm away from dishwasher

cutout on sides and 11 mm on front and back.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

IMPORTANT:

To prevent damage to right-hand hinge, open

dishwasher lid before setting dishwasher into

countertop cutout.

2. Set the dishwasher into countertop cutout.

Make sure front of dishwasher is parallel to

front edge of countertop.

3. After complete installation dishwasher should be

fully fixed by silicone. For additional support you

can use included clamps and brackets:

• Install two clamps, evenly spaced, on front

(sink) side clamp rail. To install clamps:

- hook upper clamp onto rail; use flat-blade

screwdriver to attach clamp to rail,

- use 11 mm deep-well socket and securely

tighten nut against lower clamp. Do not

overtighten.

• Install two brackets on right bottom side of

dishwasher. To install brackets:

- use screwdriver with torx tip to attach bracket

to bottom of dishwasher,

- use cross-blade screwdriver to attach bracket

to cabinet.

6÷7 mm

bead of silicone

cault

dishwasher

cutout

Cut along

this corner Back of

inner carton

rail

countertop

upper clamp

lower clamp

sink

4. Immediately remove any excess caulking. Read

Instruction for Use of silicone to know time,

which silicone need to full durability. Do not use

dishwasher until silicone has full durability.

MAKE ELECTRICAL CONNECTION

Using a power supply cord.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Plug into a grounded 3 prong outlet.

CONNECT WATER SUPPLY

1. Connect the dishwasher water fill line.

2. Connect hot and cold water lines to the tap

unit.

3. Connect the sink and dishwashing drain

plumbing.

4. Turn water supply on the both dishwasher and

sink tap unit. Check for leaks.

COMPLETE INSTALLATION

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

1. Plug in dishwasher or reconnect power.

IMPORTANT:

The following steps must be done before using the

dishwasher, to test and activate the GFCI.

Water inlet valve

Check valve

Do not remove

check valve!

Water

fill line

connection

Installation instructions

1. Unscrew two bolts (A) and remove GFCI cover

(B) located on the front base of the dishwasher

inside the cabinet.

2. Make sure that indicator (D) is in “1” position.

3. Turn on dishwasher if it is off – press main

switch (C) to “on” position (LED’s are lighting).

4. Press TEST button (E). Indicator should switch

into “0” position. If it does not dishwasher can

not be used – contact service immediately.

5. Switch back indicator into “1” position.

6. Place GFCI cover and screw down two bolts.

Check operation

• Refer to the “Instruction For Use” booklet that

came with this dishwasher and run the

dishwasher through a complete cycle.

• Check for leaks.

Andere Handbücher für KDIX 8810

Inhaltsverzeichnis

Andere KitchenAid Spülmaschine Handbücher

KitchenAid

KitchenAid Sculptura KUDI24SE Bedienungsanleitung

KitchenAid

KitchenAid KUDS02FR Bedienungsanleitung

KitchenAid

KitchenAid KUDM25SH Bedienungsanleitung

KitchenAid

KitchenAid KUDD03STPA10 Bedienungsanleitung

KitchenAid

KitchenAid 9742114 Bedienungsanleitung

KitchenAid

KitchenAid KUDT03STBL3 Bedienungsanleitung

KitchenAid

KitchenAid KUDI25CH Bedienungsanleitung

KitchenAid

KitchenAid KUDI01DL Bedienungsanleitung

KitchenAid

KitchenAid KUDC02IR Benutzerhandbuch

KitchenAid

KitchenAid KUDS24SEAL1 Bedienungsanleitung

KitchenAid

KitchenAid KUDS30FXWH1 Bedienungsanleitung

KitchenAid

KitchenAid Briva KIDS36 Bedienungsanleitung

KitchenAid

KitchenAid KUDC Series Bedienungsanleitung

KitchenAid

KitchenAid KUDE48FXSP Bedienungsanleitung

KitchenAid

KitchenAid Sculptura KUDR24SE Bedienungsanleitung

KitchenAid

KitchenAid KUDE20IXBL2 Bedienungsanleitung

KitchenAid

KitchenAid Architect II C Series KUDC10IX Bedienungsanleitung

KitchenAid

KitchenAid KUDH03DTBL - ARCHITECT II 24" Dishwasher Bedienungsanleitung

KitchenAid

KitchenAid KUDD01S Bedienungsanleitung

KitchenAid

KitchenAid KUDU03FTPA2 Bedienungsanleitung

KitchenAid

KitchenAid KUDT03FTPA1 Bedienungsanleitung

KitchenAid

KitchenAid KUDK03ITBL0 Bedienungsanleitung

KitchenAid

KitchenAid WDT750SAKW Bedienungs- und Montageanleitung

KitchenAid

KitchenAid KDSDM 82130 Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung

Siemens

Siemens SN 56N591 Bedienungsanleitung