KitchenAid KHMC106W Bedienungsanleitung

Installation Instructions

30” Built-In

Microwave

Convection Hood L

IMPORTANT:

Installer: Leave Installation Instructions with the

Homeowner.

Homeowner: Keep Installation Instructions for

future reference.

Save Installation Instructions for local electrical

inspector’s use.

READ THESE INSTRUCTIONS BEFOREYOU START TO INSTALL THIS UNIT.

KEEPINSTALLATION INSTRUCTIONS FOR FUTURE REFERENCE.

30” BUILT-IN

MICROWAVE /HOOD

MODEL

KHMC106W

INSTALLATION INSTRUCTIONS

CONTENTS:

Introduction ....................................................................... 1

Mounting Space .................................................................. 1

Wall Construction ............................................................... 2

Electrical Grounding Instructions.. ......................................... 3

Hood Exhaust Duct.. ........................................................... 4

Tools Recommended for Installation ...................................... 5

Installation Hardware .......................................................... 5

Preparation of Carton .......................................................... 6

Preparation of Product ......................................................... 6

Ventilation System ............................................................... 7

Adapting Hood Fan Unit ............................................ 7

Vertical Exhaust, Outside Ventilation.. .......................... 7

Horizontal Exhaust, Outside Ventilation ....................... 7

Recirculating, Non-Vented ......................................... 9

Preparation of Wall and Top Cabinet ...................................... 10

Mounting Templates ..................................................

Wall and Top Cabinet ................................................. 10

Preparation of Toggle Bolts ........................................ .10

Product Installation .............................................................. 11

Mounting Plates.. ...................................................... 11

Mounting Product ..................................................... 11

Check List for Installation.. ................................................... .13

Accessories

....................................................................... .13

INTRODUCTION

Proper installation is the installer’s responsibility.

A qualified technician should install this microwave oven.

Make sure you have everything necessan/ for correct installation. It is the responsibility of the installer to

comply with the installation clearances specified on the serial/rating plate. The serial/rating plate is located

behind the microwave oven door on the front frame of the microwave oven.

Remove all contents from the upper cabinet.

Important: Observe all governing codes and ordinances.

Check location

where microwave oven will be installed. The wall must be strong enough to

support

the

microwave oven weight of 150 Ibs., plus the weight of any items placed inside the microwave or the upper

cabinet. The location should be away from strong draft areas, such as windows, doors, and strong heating vents

The microwave oven should be located for convenient use in the kitchen.

Electrical ground

is required. See Electrical requirements.

Failure to use more than one person during

installation may result in personal injury

It is the customer’s responsibility to:

contact a qualified electrical installer.

assure that electrical installation is adequate

and in conformance with National Electrical

Code, ANSVNFPA 704atest edition, and

local codes and ordinances.

/ 30’

MOREFROM

COOKING SURFACE

NOTE:

Do Not use this microwave oven for com-

mercial purposes. This microwave oven is

designed for household use only. r 66’ ORMOREFROMFLOOR

MOUNTING SPACE

This Microwave Oven/Hood system requires a

mounting space on a wall as shown below:

Excessive Microwave Energy Exposure

Do Not attempt to operate this microwave oven with the door open.

Do Not tamper with or defeat the safety interlocks.

Do Not place objects between the microwave oven front face and the door.

Do Not allow soil or cleaner residue to accumulate on sealing surface of microwave oven door.

Do Not operate microwave oven if it is damaged.

The microwave oven door must close properly to provide safe operation. Do Not use microwave

oven if door is bent; hinges and latches are broken or loose; or door seals, sealing surfaces or

glass is broken.

The microwave oven should only be adjusted and repaired by a qualified repair person.

. Have a qualified repair person check for microwave leakage if a repair is made.

Failure to use microwave men except as instructed may result in exposure to excessive microwave energy.

For proper installation and servicing, a l-inch space is necessary between the top of the range backsplash

and the bottom of the Microwave Oven/Hood system.

WALL CONSTRUCTION

Personal Injury or Property Damage Hazard

This microwave oven must be mounted against and supported by a flat, vertical wall.

This microwave oven must be attached with two lag screws to a minimum of one, vertical 2” x 4”

wall stud.

Do Not mount microwave oven to an Island or peninsula cabinet.

The microwave oven top and rear supporting structures must be capable of supporting 127 Ibs.,

plus the weight of any items placed inside the microwave oven or upper cabinet.

Failure to mount the microwave oven as instructed could result in personal injury and/or property

damage.

To find the location of the studs, one of the following methods may be used:

A. Stud Finder -- a magnetic device which locates nails in the stud.

B. Use a hammer to tap lightly across the mounting surface to find

solid sound. This will indicate a stud location.

2” x 4”

WOOD STUDS

The centerofthe stud can be located by probing the wall with a small nail to find the edgesofthestud and then placing

a mark halfway between the edges. The center of any adjacent studs will normally be 16” or 24” to either side of this

mark.

NOTE: In the event that the unit will be unable to be supported by any stud, it will be necessary to use special care

in the placement of the toggle bolts and top cabinet screws. See Wall Template for details. The top cabinet should

be tested to ensure it is securely attached to the wall. Place extra weight up to 127 pounds inside the top cabinet

to test the support.

ELECTRICAL REQUIREMENTS

Electrical ground is required on this appliance.

E-&~&Hazard

Checkwithaqualifiedelectricianifyouareindoubtastowhethertheapplianceisp~perlygrounded.

Improper connection of the equipment-grounding conductor can result in electrical shock.

This appliance must be properly grounded.

Failure to do so may result in electrical shock or other personal injury,

Do Not use an extension cord with this appliance. Such use may result in a fire, electrical shock

or other personal injury

Do Not have a fuse in the neutral or grounding circuit. This could result in electrical shock or other

personal injury

A 12@volt, 60-Hz, AC only, 15- or 20-ampere, fused electrical supply (located in the upper cabinet as close

as possible to the microwave oven) is required. (Timedelay fuse or circuit breaker is recommended.) It

is recommended that a separate circuit serving only this appliance be provided.

Recommended grounding method

Do Not, under any circumstances, remove the power supply cord grounding prong.

For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply

cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into

a mating 3-prong grounding type wall receptacle, grounded in accordance with the National Electrical Code,

ANSVNFPA 7Watest edition, and local codes and ordinances. (See Figure 1.) If a mating wall receptacle IS

not available, it is the personal responsibility and obligation of the customer to have a properly grounded,

3prong wall receptacle installed by a qualified electrician.

3-prong

grounding Plug

powei supply cord

grounding prong

3-prong grounding

type wall receptacle

Figure 1

Electrical Shock Hazard

Ike special care when drilling holes into the wall. Electrical wires may be concealed behind the wall

covering and contact with them could result in electrical shock

Locate any electrical circuits that could be affecW by the installation of this product and disconnect

power circuit

Failure to do so could result in electrical shock

HOOD EXHAUST DUCT

When the hood is vented to the outside, a HOOD EXHAUST DUCT is required. All ductwork must be metal

(do not use plastic duct). Check that all connections are made securely. Please read the following carefully:

Fire Hazard

Mntirg system must terminate to the outside. Do Not terminate the ductwoh in an attic or other

enclosed space. Do Not use 4” laundrytyp wall caps.

To do any of the above may resutt in a fife.

EXHAUST CONNECTION: The hood exhaust has been designed to connect to a standard 3-l/4” x10”

rectangular duct.

If round duct is required, a rectangular-to-round adaptor must be used. do not use a duct that is

less than

6”

in diameter.

REAR EXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the

exhaust with the space between the studs, or wall should be prepared at the time it is constructed by

leaving enough space between wall studs to accommodate exhaust.

MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of 3-1/4”xlO”

rectangular or 6” diameter round duct should not exceed 140 feet.

ELBOWS, ADAPTORS, WALL, ROOF CAPS, etc. present additional resistance to air flow and are equivalent

to a section of straight duct which is longer than their actual physical size. When calculating the total

length, add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections.

The diagram below shows the approximate feet of equivalent length of some typical ductwork parts. Use

the values in parentheses for calculating air flow resistance equivalent, which should total less than 140 feet.

EXHAUST DUCT

90°

ELBOW

(10 FT.1

(r WIDE ELBOW(10 FT.)

WALLCAP

(40 FT.1

ff2

45’

ELBOW(5 FT.)

90° ELBOWUS FT.1

ROOFCAP

04 IT.)

ADAPTOR (5 FT.1

45.

ELBOW(5 FT.)

WALL AND ROOF CAPS USED MUST HAVE BACK-DRAFT DAMPER.

TOOLS RECOMMENDED FOR INSTALLATION

Phillips Screwdriver

Electric Drill

l/2”, 5/8” and 3/32’ Drill Bits

1-l/2’ Wood Bit or metal hole cutter (if metal cabinet is used)

Saw to cut exhaust opening (if needed)

Knife or single edge razor

Pencil

Measure

Tape

Protective drop cloth for product and range. You may use part of the carton for protection.

INSTALLATION HARDWARE

The installation hardware (items l- 8) packed with the product should contain the following:

1 ITEM NAME QUANTITY

1 Wood Screw 5 x 30 mm* 6

2 Toggle Bolt 3/l 6 inch* 4

3 Top Cabinet Screw 5 x 55 mm 2

4 Flat Washer 30 mm diameter 2

5 Decorative Screw 2

6 Power Cord Hanger 1

7 Grommet 1

8 Exhaust Adaptor Assembly 1

*There may be leftover screws or toggle bolts depending on installation.

se with metal cabinets. Surround

e power cord opening. Cut to fit.

PREPARATION OF

CARTON

Utilization of the canon may make installation easier.

CHECK THE PRODUCT FOR DAMAGE

1. Remove product and shipping pads. Visually check the product after removing from carton.

Remove all packing material from inside the oven cavity.

Check the oven for any damage, such as misaligned door,

damaged gaskets around door or dents inside the oven

cavity or on the door. If there is any damage, please do not

operate the oven until it has been checked by your Kitch-

enAid Dealer and any necessary repairs made.

PREPARATION OF PRODUCT

1. Rest the product on its side as shown in Figure 1. Use a portion of the carton or some other material

to protect the outercase. Failure to do so could result in damage to the outercase of the unit.

2. pull the two slider levers to release the mounting plate hooks. R

emove the mounting plates from the

back of the product by gently pulling each plate toward you and sliding it to the right. Familiarize

yourself with the operation of the upper hooks and the slider fevers so you will be aware of the proper

procedure for mounting the unit to the wall.

Upper Hooks

Mounting Plates

IQ:

$7 m

.. .

. cs=

irs

> Slider levers

Figure 1.

VENTILATION SYSTEM

THIS MICROWAVE OVEN/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THREE TYPES OF HOOD

VENTILATION SYSTEMS:

A. Vertical Exhaust

-- outside ventilation

B. Horizontal Exhaust

-- outside ventilation

C. Recirculating

-- non-vented, ductless

Select the type required for your installation.

Recirculating (ductless) installation requires

CHARCOAL FILTER.

Your Microwave Oven/Hood System is preset for VERTICAL Exhaust; follow the procedure below (A) to attach the

Exhaust Adaptor Assembly if your installation will use a vertical exhaust system. If you will need to use a

HORIZONTAL exhaust system, proceed to step

or for a RECIRCULATING system, proceed to page 9 (step C).

VERTICAL EXHAUST: Outside Ventilation

The unit is shipped assembled for vertical exhaust. Remove the 2 tapping screws

the Exhaust Adaptor to the fan cover on the top of the outercase cabinet with the 2

shown in

Figure 2.

Proceed to

Preparation of Wall and Top Cabinet

on page 10.

from the fan cover. Attach

tapping screws provided as

Exhaust Adaptor Assembly - - -

Figure 2

B. HORIZONTAL EXHAUST: Outside Ventilation

1. Remove and save 3 screws.

Remove fan cover bracket shown in

Figure 3.

Fan Cover Bracket - - - /

Figure

HORIZONTAL EXHAUST (Continued)

2. Withdraw hood fan unit upward carefully

(Fig.4).

Figure 4 1.

3. Rotate hood fan unit l/4 turn

shown in

Figure5

Figure 5

4. Replace hood fan unit into the oven unit.

Be careful not to pinch the lead wire between

the inner bracket and the hood fan unit

(Fig.6).

Figure 6

Andere Handbücher für KHMC106W

Inhaltsverzeichnis

Andere KitchenAid Mikrowellenofen Handbücher

KitchenAid

KitchenAid KHHC2090SSS - Architect II 2.0 cu. ft. 1200... Bedienungsanleitung

KitchenAid

KitchenAid MK1157XJ Bedienungsanleitung

KitchenAid

KitchenAid KBMS1454SBL1 Bedienungsanleitung

KitchenAid

KitchenAid KHHC2090S Bedienungsanleitung

KitchenAid

KitchenAid KHHC2090SBL - Architect 2.0 Cu Ft Microwave... Bedienungsanleitung

KitchenAid

KitchenAid KMHC319ESS Bedienungsanleitung

KitchenAid

KitchenAid KBMC147HBL05 Bedienungsanleitung

KitchenAid

KitchenAid KHMS2056SSS - ARCHITECT II 36" 2.0 cu. Ft. 1 Bedienungsanleitung

KitchenAid

KitchenAid Architect Series KBMS1454R Bedienungsanleitung

KitchenAid

KitchenAid KCMS185J Bedienungsanleitung

KitchenAid

KitchenAid YKCMS1655 Bedienungsanleitung

KitchenAid

KitchenAid KMHS120EWH0 Bedienungsanleitung

KitchenAid

KitchenAid YKMHS120ES Bedienungsanleitung

KitchenAid

KitchenAid KCMS1655BWH Gebrauchs- und Wartungshandbuch

KitchenAid

KitchenAid 8304532A Stücklistenhandbuch

KitchenAid

KitchenAid KCMC155J Bedienungsanleitung

KitchenAid

KitchenAid KMCS1016GSS Bedienungsanleitung

KitchenAid

KitchenAid MICROWAVE HOOD Bedienungsanleitung

KitchenAid

KitchenAid KCMS2055SSS - Architect Series II Bedienungsanleitung

KitchenAid

KitchenAid KCMS135H Bedienungsanleitung

KitchenAid

KitchenAid KCMS1555R Bedienungsanleitung

KitchenAid

KitchenAid 30” Built-in Microwave Hood Bedienungsanleitung

KitchenAid

KitchenAid KHMS1850SWH1 Bedienungsanleitung

KitchenAid

KitchenAid YKHMS1850S Bedienungsanleitung

Beliebte Mikrowellenofen Handbücher anderer Marken

Daewoo

Daewoo KOG-574R0S Bedienungsanleitung

LG MH7040SS Bedienungsanleitung

Sharp

Sharp R-895(AL)M Bedienungsanleitung

Dometic

Dometic DOTRM13W Bedienungsanleitung

Sanyo

Sanyo EM-X680 Bedienungsanleitung

Sharp

Sharp R-393M Bedienungsanleitung

Smeg

Smeg S45MCX1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHM2044 Bedienungsanleitung

Sunbeam

Sunbeam SMW759 Bedienungsanleitung

Bosch

Bosch CEG732X.1B Bedienungsanleitung

Dometic

Dometic Roadmate 230 Bedienungsanleitung

Samsung

Samsung SJ0396W Bedienungsanleitung

Sanyo

Sanyo EM-P494WS Bedienungsanleitung

Sharp

Sharp R-240 Bedienungsanleitung

Electrolux

Electrolux EMS2840 Bedienungsanleitung

Daewoo

Daewoo KOC-984T2S13 Bedienungsanleitung

Impecca

Impecca CM07M2 Bedienungsanleitung

Sanyo

Sanyo EM-G5596V UK2 Bedienungsanleitung