KNX Module PS-S.640.30.1 Bedienungsanleitung

module-electronic.ru

KNX POWER SUPPLY

PS-S.640.30.1

Application Program: ver. 1.0

User Manual: ver. 1.0

User Manual

CONTENT

Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1 Basic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Speciﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Operational description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Device/busline diagnostics application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2.1 Measurement sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2.2 Event counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2.3 Event counter reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Parameter structure for measurement sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.1 Programing button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.2 Individual address assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.5 KNX bus reset function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3 ETS database parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.3 Maximum tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Telegram traﬀic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.5 Error counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.6 Operational counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.7 Alarm 1,2,3,4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4 Communication objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5 State of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.1 Default factory setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

page 2

module-electronic.ru

1 BASIC INFORMATION

Intelligent power supply for the KNX system with an additional auxiliary power output of 29V DC, with the

function of diagnostics of voltage in the KNX bus and protective against short circuit and overload.

• Compact housing (2TE)

• Additional output 29V DC

• Diagnostic function

• LED status indication

• Output current 640mA

• Leakage < 5W

• Mains voltage 230V AC 50Hz

• Overload and short circuit protection

• Bus line reset via local push button or remote

• DIN rail 35mm mounting

PS-S.640.30.1

page 3

module-electronic.ru

1.1 SPECIFICATION

Device model

PS-S.640.30.1

Power input

Mains voltage

230V AC ± 10% 50Hz

Power consumption normal / max. overload

23W / 42W

Mains failure bridging time

> 100ms

Mains voltage connection

screw terminals 0,3...2,5mm²

Power output

KNX, AUX output voltage

28...31V DC

Rated current / max. current (total output)

640mA / 1,2A

Eﬀiciency at nominal load

82%

KNX interface

Speciﬁcation

TP-256

Available application soware

ETS 4 and later

KNX connector

4-wire EIB connector (PUSH WIRE spring clips) for standard cable TP1 0,8мм Ø

KNX physical address by default

12.12.255

Operation temperature

-5°C ... + 45°C

Operation humidity

5 ... 95% (no condensation)

Degree of protection

IP 20, clean environment

Mounting type

DIN rail 35mm

Dimensions

36 х 90 х 71mm (2TE)

Weight

185 g

page 4

module-electronic.ru

90mm

36mm 71mm

A. Supply voltage terminals B. Reset button C. Programming button D. Aux output connector E. KNX TP connector

1. LED input voltage V 2. LED bus voltage V 3. LED telegram traﬀic 4. LED output current I

IN BUS OUT

5. LED internal temperature 6. LED KNX reset 7. Programming LED

1. Input voltage VIN

Green: Input voltage is 195...265V AC

Red: Input voltage is out of this range

2. Bus voltage VBUS

Green: KNX bus voltage 28...31V DC

Red: KNX bus voltage is out of this range

3. Telegram traﬀic

Green (blinking): Telegram traﬀic < 80%

Red: Telegram traﬀic > 80%

4. Output current I

OUT

Green: I < 640mA

OUT

Orange: I 640...900mA

OUT

Red: I > 900mA (overload)

OUT

5. Internal temperature

Green: Temperature is 0...75°C

Red: Temperature is out of this range

6. KNX reset

Red: Restart of the KNX bus line is running

7. Programming

Red: Programming mode active

1.2 APPEARANCE

page 5

module-electronic.ru

KNX bus

AUX KNX

L N

AUX

1.3 INSTALLATION AND CONNECTION

INSTALLATION

WIRING DIAGRAMS

Attaching to DIN rail

Removing from DIN rail

ATTENTION! Installation and connection of the device to the mains must only be carried

out by qualiﬁed personnel! There is a risk of electric shock! Be sure to turn oﬀ the power

before installing or removing the device! Even when the device is turned oﬀ, the output

terminals can be live! Do not connect to the outputs a load that exceeds the

recommended values! The design of the device meets the requirements of electrical

safety according to GOST 12.2.007.0-75.

page 6

module-electronic.ru

2 OPERATIONAL DESCRIPTION

In network installations, PS-S.640.30.1 supplies one KNX TP line and monitors all relevant data. With its

default settings the PS-S.640.30.1 operates as is supposed to.

Communication objects are used to request device status and measurement values. The measured values

can be sent aer request, aer a certain change (measured value, device status) and periodically. Here, a

certain change of the measured value means the diﬀerence between actual value and last sent value.

Number and duration of overloads are stored. The same applies for the number of short circuits, device

startups, KNX bus resets and for the duration of load detachments. The total operating time of the device

and its operating time since last device startup are stored, too. Threshold values can be set for the bus

voltage (only in the additional alarms), total current, telegram traﬀic and internal device temperature.

Regarding maximum current values and maximum device temperature values, a tracking period can be

set. At the end of every tracking period the maximum measured value can be sent on the bus or just be

set as value of the appropriate object. Four diﬀerent Alarm tabs (see chapter 3.7) can be used to send an

info telegram (containing «0» or «1») about over/under threshold events and to switch other devices. Aer

assignment of the measurement source («Output current», «Device temperature», «Output Voltage») each

alarm can be conﬁgured individually.

2.1 DEVICE/BUSLINE DIAGNOSTICS APPLICATION

The diagnostic measurement sources and event counters can be activated and deactivated. When

activated, the device monitors the relevant values.

2.2 DIAGNOSIS

The bus voltage, bus current and internal device temperature are measured constantly. The telegram

traﬀic extent is determined additionally. For each of these measurement sources a threshold value can be

set. Aer setting the threshold value the threshold type can be selected (limit undercut/limit exceeded)

and the behaviour on alarm activation/deactivation can be conﬁgured. A maximum value tracking feature

with pre-settable tracking period can also be activated.

2.2.1 MEASUREMENT SOURCES

page 7

module-electronic.ru

2.2.2 EVENT COUNTERS

For diagnosis purpose, event counters provide number and duration of overloads. When there is a short

circuit on the bus, the load will be disconnected from the output automatically. Number of short circuits

and duration of load detachment are available details. The same applies for the number of KNX bus resets

and of device startups, and for operating times. Additional alarms also provide the number of a value

being in the threshold range and the duration of such event.

Event

Number Counter

Duration Counter

Overload

Short Circuit

Load Detached

KNX Bus Reset

Threshold Range

Operating Time

(total/since last startup)

Device Startup

Table 1. Available event counters

2.2.3 EVENT COUNTER RESET

Counters for total operating time and device startups cannot be reset. Other counters for events can be

reset by communication object. These counters (number and duration) are set to zero by writing a «1» to

the communication object no.33 «Counter reset».

The event counter of each individual alarm (1,2,3,4) is set to zero by writing a «0» to the related

communication object «Duration X» (objects no. 21, 24, 27, 30). Both number and duration counters then

will be reset.

page 8

module-electronic.ru

2.3 PARAMETER STRUCTURE FOR MEASUREMENT SOURCES

On enabling a measurement source in the ETS tab «Measurements», the following parameter structure is

available (exception: counters). An actual value can be sent over the bus aer a certain value change

(«Sending diﬀerence») or aer a pre-set time period has elapsed («Cyclic sending»). A value reaching the

excess threshold range can be used to send telegrams containing «1» or «0» («Behaviour on alarm

activation»). Leaving this excess threshold range activates the «Behaviour on alarm deactivation». The

additional alarms have an extended adjustment.

ETS Parameter

Explanation

Object type

Selection of the datapoint type

Sending diﬀerence

The actual value is sent when the diﬀerence between last sent value and

actual value reaches the pre-set diﬀerence

Cyclic sending

The actual value is periodically sent

Threshold alarm

Enables/disables the threshold functionality and following options

Threshold

Crossing this limiting value executes the «Behaviour on alarm activation»

function

Hysteresis

Passing the «Threshold» - «Hysteresis» value executes the «Behaviour on

alarm deactivation» function

Behaviour on alarm activation

Set action on activation: Send a telegram or set the internal object value

Behaviour on alarm deactivation

Set action on deactivation: Send a telegram or set the internal object

value

Table 2. General menu structure

2.4 PROGRAMMING

2.4.1 PROGRAMMING BUTTON

To download the desired Individual Address or an ETS setting the Programming Button must be pressed

ﬁrst. Successive pressing the Programming Button will turn on and oﬀ the Programming Mode. LED 7

lighting in red colour indicates Programming Mode is active. When Programming Mode is active, ETS

recognizes the device of interest for downloading.

page 9

module-electronic.ru

2.4.2 INDIVIDUAL ADDRESS ASSIGNMENT

To conﬁgure the device an interface connection (IP, USB) to the KNX bus system is required. The device is

supplied with the Individual Address 12.12.255. The KNX product database entry (available for ETS4 and

higher) can be downloaded from the website and from the KNX Online Catalog.

With the ETS the Individual Address can be assigned to the device by setting the desired address in the

properties window of the ETS. Aer starting the ETS download and then pressing the Programming

Button the device restarts itself.

Figure 1. ETS properties window

page 10

module-electronic.ru

Inhaltsverzeichnis

Andere KNX Stromversorgung Handbücher

KNX

KNX AS 36 3 knx Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung