Kodak Magnus VLF Q2400 Bedienungsanleitung

Magnus VLF Q2400/Q3600

Platesetter

Model MTA

Safety Guide for Operators

Original instructions

English

2020-10-28

761-00039B-EN Rev C

Some documentation is distributed in Portable Document Format (PDF). You may reproduce such documentation from

the PDF file for internal use. Copies produced from the PDF file must be reproduced in whole.

Trademarks

Kodak, Creo, eCentral, Flexcel, Magnus, Quantum, and ThermoFlex are trademarks of Kodak.

FCC compliance

Any Kodak equipment referred to in this document complies with the requirements in part 15 of the FCC Rules for a

Class A digital device. Operation of the Kodak equipment in a residential area may cause unacceptable interference to

radio and TV reception, requiring the operator to take whatever steps are necessary to correct the interference.

REACH

REACH is a European Union regulation concerning the Registration, Evaluation, Authorization and Restriction of

Chemicals. Under Article 33 of EU REACH Regulation (1907/2006), Eastman Kodak Company has a duty to

communicate to our customers the presence of substances of very high concern (SVHC) in excess of 0.1% by weight of

articles contained in our products.

For Kodak platesetters, imagers, and Kodak branded accessories, this information can be found on our service knowledge

portal (Answer ID 73755).

For further information regarding REACH compliance of Eastman Kodak Company’s products contact WW-

[email protected].

Waste management

Kodak Commercial Imaging Machinery/Equipment is currently not classified as hazardous under Directive 2008/98/

EC, as amended. Dispose under European Waste Catalogue Code 16 02 14 according to the local regulations or

guidelines that apply to this category of non-hazardous waste.

Ensure the use of properly authorized waste management companies in all markets worldwide.

https://www.kodak.com/print/default.htm

761-00039B-EN Rev C

Revised 2020-10-28

Contents

1 Introduction to safety information.................................................................................................1

Read this guide................................................................................................................................................................................1

Definitions........................................................................................................................................................................................1

Safety standards and compliance labels.................................................................................................................................3

Sources of additional safety information................................................................................................................................7

Types of safety messages...........................................................................................................................................................7

2 Safe operation.....................................................................................................................................9

Keep panels closed during operation.......................................................................................................................................9

Handle plates safely...................................................................................................................................................................10

Handle magnetic clamps safely................................................................................................................................................11

Airborne emissions......................................................................................................................................................................11

3 Safe maintenance.............................................................................................................................17

4 Safety features...................................................................................................................................21

Safety interlock system..............................................................................................................................................................21

Power/emergency stop switch...............................................................................................................................................24

Emergency stop buttons...........................................................................................................................................................25

APL safety features.................................................................................................................................................................... 27

Compressed air supply shutoff valve....................................................................................................................................29

5 Hazards...............................................................................................................................................31

Laser hazards................................................................................................................................................................................31

Mechanical hazards................................................................................................................................................................... 35

Electrical hazards........................................................................................................................................................................38

vi Magnus VLF Q2400/Q3600 Platesetter Safety Guide for Operators

1Introduction to safety

information

Before operating a Kodak platesetter, read this safety guide, understand

the safety terminology, and know where to find more safety

information.

Read this guide

Read this safety guide before you operate the platesetter or perform

any maintenance procedures on it. This document must be accessible

to anyone who operates the platesetter.

WARNING: Failure to read, understand, and follow the information in this guide

may result in the incorrect operation of this product and can create a hazardous

situation, which, if not avoided, can result in death or serious injury.

Familiarize yourself with the safety labels. Labels remind you of critical

safety information while you are operating and maintaining the

platesetter. If the labels do not provide safety information in the

language used in your workplace, ask your authorized service

representative if labels in that language are available.

The platesetter has safety features that reduce the risk of harm from

the hazards that are associated with this type of device, including:

●Laser radiation

●Moving mechanical parts

●Hazardous voltage electrical parts

This document describes these hazards, shows where you might

encounter them, and explains the safety features that reduce the risk of

harm from them. It also directs you to procedures for safe media

handling and platesetter maintenance.

Definitions

This document assumes an understanding of certain terms.

Automatic Pallet Loader (APL) option

A platesetter automation option for very large format (VLF)

plates that provides automated plate loading and slip sheet

removal from multiple shipping pallets. Plates are also unloaded

automatically.

Authorized service representative

Someone whom Kodak has approved to perform a service

procedure. Authorized service representatives are trained in the

proper procedures for working with and adjusting the laser

system and for working with the mechanical and electrical

systems of the platesetter.

Cassette

A plate storage area located in the front of a platesetter with

the single-cassette unit (SCU) or multi-cassette unit (MCU)

options. It holds a stack of plates, with or without slip sheets, for

automatic loading. It has guides that can be adjusted to hold

different plate sizes.

Multi-cassette unit (MCU) option

A platesetter automation option that provides automated plate

loading with slip sheet removal from multiple plate cassettes.

Plates are also unloaded automatically.

Operator

Someone whose primary responsibility is to load plates into the

platesetter or its automatic loading system and start the

exposure process. In some cases, depending on the platesetter

and its options, operators also unload the exposed plates.

Operators can remove stuck plates or plates that were

improperly picked by the automatic loading system or that have

fallen off the imaging drum inside the platesetter, and they

might be responsible for some maintenance tasks in areas that

operators are allowed to access.

Operator access tool

A flat-head screwdriver.

Panel

A large section of the exterior or interior surface of the

platesetter. Operators can open or remove the rear panel,

power box filter panel, and fan box panel for maintenance or

error recovery. An operator secures these panels with a flat-

head screwdriver or by closing them by hand. All other panels

are accessible only to service representatives.

Punch option

An optional module positioned at the rear of the automated

platesetters. The punch option automatically receives plates

2 Chapter 1—Introduction to safety information

from the unload table, cuts registration features into the plates,

and ejects them to the plate processing equipment or plate

stacker.

Rear hood

A hinged section of the exterior surface of the platesetter that is

relied upon as an access panel. Operators can unlock and lift

the rear hood for maintenance or error recovery.

Universal debris removal cabinet (UDRC)

An accessory that filters potentially harmful airborne emissions

released during imaging certain types of media. It is optional for

platesetters but required for Kodak Flexcel NX imagers.

Safety standards and compliance labels

The platesetter is designed, built, and tested according to

internationally recognized safety standards for reducing the risk of

death and serious injury from laser, mechanical, and electrical hazards.

The platesetter complies with the following standards:

●Class 1 laser product as specified in U.S. Federal Regulations 21 CFR

1040.10, in accordance with the regulations of the Center for

Devices and Radiological Health (CDRH)

●EN ISO 12100: 2010

Safety of Machinery—General Principles for

Design—Risk Assessment and Risk Reduction

●EN ISO 13849-1: 2008

Safety of Machinery, Safety-Related Parts of

Control Systems. Part 1: General Principles for Design

●EN 60825-1: 2014

Safety of Laser Products; Class 1 Laser Product

●CSA 60950-1: 2007 +A1 +A2

Information Technology Equipment;

Safety; Part 1

●UL 60950-1: 2014

Information Technology Equipment; Safety; Part 1

●EN 60950-1: 2006 +A11 +A1 +A12 +A2

Information Technology

Equipment; Safety; Part 1: General Requirements

●EN 60204-1: 2006 + A1

Safety of Machinery, Electrical Equipment

of Machines. Part 1: General Requirements

●EN 55011: 2016

Industrial, Scientific and Medical Equipment -

Radio-Frequency Disturbance Characteristics - Limits and Methods

of Measurement (CISPR 11), Class A

●EN 61000-6-1: 2007

EMC - Part 6-1: Generic Standards. Immunity

for Residential, Commercial and Light-Industrial Environments

●Low Voltage Directive 2014/35/EC

Safety standards and compliance labels 3

●Machinery Directive 2006/42/EC

●EMC Directive 2014/30/EC

●Class A product as specified in U.S. Federal Communications

Commission (FCC) Rules, part 15

●Airborne noise emissions at a maximum of 78 dB(A)

●Operating ambient temperature at a maximum of 30°C (86°F)

Note: The international standards listed in this guide are subject to change. To

check the latest standards that apply to your model, review the latest

Declaration

of Conformity

certificate available on your service and knowledge information

portal.

Dataplate label on the platesetter

The dataplate label displays many regulatory compliance markings and

the platesetter's serial number. The label is located at the rear of the

platesetter, near the power switch.

Figure 1: Dataplate label on the Magnus VLF platesetter

Compliance labels

The labels that show compliance with United States Federal

Communications Commission (FCC) rules and with U.S. Center for

Devices and Radiological Health (CDRH) requirements are located at

the rear of the platesetter, near the power switch.

4Chapter 1—Introduction to safety information

Andere Handbücher für Magnus VLF Q2400

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kodak Drucker Handbücher

Kodak

Kodak G610 - EasyShare Printer Dock Photo Bedienungsanleitung

Kodak

Kodak PROFESSIONAL LED II 20R Bedienungsanleitung

Kodak

Kodak VERSAMARK DS5110 Bedienungsanleitung

Kodak

Kodak 6900 Bedienungsanleitung

Kodak

Kodak VERSAMARK DP7122 Handbuch

Kodak

Kodak Photo Printer 6850 Bedienungsanleitung

Kodak

Kodak VERITE CRAFT 6 Bedienungsanleitung

Kodak

Kodak DIGITAL MULTIPRINTER II - SITE Bedienungsanleitung

Kodak

Kodak 9810 - PRINTING IMAGES FROM PHOTOSHOP 7 AND... Bedienungsanleitung

Kodak

Kodak Mini Bedienungsanleitung

Kodak

Kodak 1400 Bedienungsanleitung

Kodak

Kodak Professional ML-500 Leitfaden

Kodak

Kodak 305 Installations- und Betriebshandbuch

Kodak

Kodak 305 Bedienungsanleitung

Kodak

Kodak VERITE 64 series Service-Handbuch

Kodak

Kodak Photo Printer 6850 Bedienungsanleitung

Kodak

Kodak EKTAPRO 7000 Bedienungsanleitung

Kodak

Kodak EasyShare printer dock Bedienungsanleitung

Kodak

Kodak 8670 PS Konfigurationshandbuch

Kodak

Kodak SRP 30 Handbuch

Kodak

Kodak D4000 Bedienungsanleitung

Kodak

Kodak NexPress M700 Bedienungsanleitung

Kodak

Kodak Smile Bedienungsanleitung

Kodak

Kodak EasyShare 350 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung