Kodak EKTAGRAPHIC III Bedienungsanleitung

Operating Manual

PRESENTATION TECHNOLOGIES

KODAK

EKTAGRAPHIC III

Slide Projectors

Important Safety Instructions

When using your projector, always follow basic safety precautions:

1. Read and understand all instructions before using this equipment.

2. Operate this projector with 110- to 125-volt 60 Hz current only. Incorrect voltage can cause projector

malfunction. See “Startup” on page 3 for Models III BR and III ABR, which feature a multi-voltage

selector.)

3. Close supervision is necessary when any appliance is used by or near children, or others who may not

understand the need for these precautions. Do not leave the projector unattended during use.

4. Be careful not to touch hot parts. For lamp replacement, allow the module to cool before touching the

lamp and the surrounding area. Do not place the lamp module on heat-sensitive surfaces.

5. Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged

(see “How to Obtain Service” on page 30).

6. Position the cord so that it is not tripped over, pulled, or placed in contact with hot surfaces.

7. If an extension cord is necessary, use a cord with a current rating at least equal to that of the projector.

Cords rated for less amperage than the projector may overheat.

8. Always unplug the projector from the electrical outlet before cleaning and servicing and when it is not

in use.

9. Allow the projector to cool before storing.

10. Do not immerse this equipment in water or other liquids.

11. Do not disassemble this projector. Use a qualified service technician when service or repair is required.

Incorrect reassembly can cause electric shock the next time the projector is used.

12. Use only safety electrical low-voltage (SELV) devices.

13. The use of an accessory attachment not recommended by the manufacturer may increase risk of

damage.

14. Keep the air-flow vents unobstructed.

Save These Instructions

Operating Manual

KODAK

EKTAGRAPHIC III

Slide Projectors

Congratulations!

You have just purchased a KODAK EKTAGRAPHIC III Slide Projector with

a KODAK Extra Bright Lamp Module.

This new lamp module procides 30% greater light intensity so your images

look brighter, richer and more saturated. This module features a “Lamp On”

indicator on the lamp module door.

KODAK EKTAGRAPHIC III Slide Projector 1

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Loading the Slide Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Projecting Your Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Editing Your Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Clearing a Gate Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Using the Built-In Viewer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Using a Dissolve Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Changing the Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Cleaning the Condenser, Heat-Absorbing Glass, and Mirror . . . . . . .23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Serial Number

The serial number of your projector is printed on the label afﬁxed to the power

cord retainer on the base of the projector. Record this number, as well as the

model identiﬁcation, date, and place of purchase, for future reference.

2 KODAK EKTAGRAPHIC III Slide Projector

Overview

FRONT RIGHT

BACK RIGHT

BASE

1 – Tray

2 – Lock Ring

3 – Storage Compartment/Remote

4 – Elevating Foot

5 – Elevating Adjustment Wheel

6 – Elevating Foot Release Button

7 – Lens

8 – Viewer (Model ATS)

9 – Focus Knob

10 – Autofocus (Models A, AMT, & ATS)

11 – Select Bar

12 – Timer (Models AMT & ATS)

13 – Reverse

14 – Forward

15 – Power/Fan/Half Lamp/Full Lamp

16 – Tray Release Latch

17 – Lamp Module

18 – Raised Index Mark

19 – Reading Light Cover

20 – Standby Light (Model E Plus)

21 – Special-Application Receptacle

22 – Remote Receptacle

23 – Power Cord

24 – Power Cord Retainer

25 – Leveling Foot

KODAK EKTAGRAPHIC III Slide Projector 3

Introduction

Take the time to read the instructions in this operating manual to become

familiar with your KODAK EKTAGRAPHIC III Slide Projector and how to

operate it properly.

Operation

Startup

Models III BR

and ABR Only

Important

Before you turn on your new KODAK EKTAGRAPHIC III BR or ABR Slide

Projector, it is critical to set the voltage selector to the proper setting. Use

the proper fuse for the voltage selection. See the fuse label on the back of the

projector.

The voltage selector on the KODAK EKTAGRAPHIC III BR or ABR Slide

Projector is located on the base of the projector. Using a small object, such as

a coin, you can set the voltage selector for the proper voltage (100, 115, 130,

220, 230, and 240 V).

4 KODAK EKTAGRAPHIC III Slide Projector

Operation

EKTAGRAPHIC III BR and ABR Slide Projectors have a sensing capability

to automatically set the proper power cycle (50 or 60 Hz). This eliminates the

need to manually change the two-position switch included on models

manufactured before November 1996. These projectors are shipped with a

detachable power cord that is packaged separately (not wound on the Power

Cord Retainer).

Asparefuseisprovided.The fuse is located in the small, pull-out storage door

below the Power Inlet. Simply pull the door with your ﬁnger. Remove the

spent fuse with a small object (e.g., pencil tip) by pushing the fuse up and

removing it from the receptacle. Press the spare fuse into the receptacle and

close the storage door.

Important

The EKTAGRAPHIC III BR and ABR Slide Projectors are supplied with a

3-wire grounding power cord to comply with UL122 (USA) and CSA222

(Canada)safety and electrical standards. We urge you to provide a permanent,

properly installed 3-wire receptacle as the source of power for this projector.

For advice and assistance, call a licensed electrician or your local power

company.

When used outside the United States of America, please use a proper adapter

that ensures grounding and polarization.

Although the Models III BR and ABR are approved to the standards of UL

and CSA, they are not intended to meet approval in all countries worldwide.

KODAK EKTAGRAPHIC III Slide Projector 5

Operation

Models A,

AMT and ATS Open the storage compartment and remove the remote control.

Plug the 5-pin cable remote connector into the remote-control receptacle,

aligning the raised dot with the metallic rivet head.

This receptacle also accepts plugs for accessories, such as Kodak dissolve

controls.

Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz

current only.

6 KODAK EKTAGRAPHIC III Slide Projector

Operation

Loading the Slide Tray

A KODAK EKTAGRAPHIC Universal Slide Tray is designed to hold up to

80 slides. Be sure that your slide mounts are in good condition; frayed or bent

mounts may fail to drop into the projector. A variety of slide trays are

available with capacity up to 140 slides. See your dealer in Kodak products

for a complete list of Kodak trays and accessories.

Note: Do not attempt to project slides mounted with sticky or loose tape.

Place the tray over the center post of the projector. Align the "0" slot with the

gate index; the tray will drop into position.

If your 80-slide tray does not drop easily, rotate the metal plate on the bottom

of the tray until it locks into position. For a 140-slide tray, secure the lock

ring, invert the tray, and align the index hole with the index notch. Slide and

hold the tray release latch in the direction of the arrow, and turn the bottom

plate until the index hole and notch align. Then release the latch.

80-Slide Tray 140-Slide Tray

Andere Handbücher für EKTAGRAPHIC III

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kodak Projektor Handbücher

Kodak

Kodak FLIK X4 Bedienungsanleitung

Kodak

Kodak S-AV 1020 Bedienungsanleitung

Kodak

Kodak Instamatic M Series Bedienungsanleitung

Kodak

Kodak Pocket Portable Projector Bedienungsanleitung

Kodak

Kodak EKTAPRO Bedienungsanleitung

Kodak

Kodak Carousel S-RA2000 Bedienungsanleitung

Kodak

Kodak KP1500A Bedienungsanleitung

Kodak

Kodak Ektalite 500 Bedienungsanleitung

Kodak

Kodak LUMA 350 Bedienungsanleitung

Kodak

Kodak V600 Bedienungsanleitung

Kodak

Kodak Luma 75 Bedienungsanleitung

Kodak

Kodak Luma 75 Bedienungsanleitung

Kodak

Kodak Instamatic M80 Bedienungsanleitung

Kodak

Kodak Pocket Pico Projector Bedienungsanleitung

Kodak

Kodak DP850 - Ultra Digital Projector Kurzanleitung

Kodak

Kodak DCS 600 Series Benutzerhandbuch

Kodak

Kodak DP850 - Ultra Digital Projector Bedienungsanleitung

Kodak

Kodak EKTALITE Bedienungsanleitung

Kodak

Kodak Brownie A15 Bedienungsanleitung

Kodak

Kodak Pocket Pico Projector Bedienungsanleitung

Kodak

Kodak DP2000 - Digital Projector Bedienungsanleitung

Kodak

Kodak Carousel S-AV 2050 AF Bedienungsanleitung

Kodak

Kodak Carousel 760 Bedienungsanleitung

Kodak

Kodak Carousel 850H Betriebsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung