Kogan Certa CT529IN1GCKA Bedienungsanleitung
52CC 9-IN-1 LINE TRIMMER HEDGE
TRIMMER CHAINSAW AND CUTTER
CT529IN1GCKA
•For safety reasons, minors are not allowed to work with the trimmer, except
persons over 16 years of age who are trained under supervision.
•Operate the trimmer in good physical and mental condition. Do not use the device
in an ill or tired state or under the influence of any substances or medical
preparations that may affect vision, physical or mental condition.
•Work only during daytime or with good artificial light.
•Do not start working without preparing the work area. Carefully inspect the area of
the proposed mowing, remove foreign objects that may be thrown away by the
cutting unit or may be attached to it.
•It is not recommended to work with a trimmer alone. Make sure that when you are
working within hearing distance of another person in case you need help.
•Unauthorised people, children and animals should be kept at a safe distance
outside the work area. Do not allow others to come closer than 15m from a working
device. People at risk (near the work area) should wear safety glasses.
•Check the trimmer before operating to ensure that all the handles, mounts and
guards are in place and good condition.
•Work in tight and durable clothing that can protect any solid objects in the case of
a cutting node. Do not wear excessively wide clothing and jewellery, as they may
fall into the moving parts of the device. Wear sturdy protective gloves. Gloves not
only protect your hands from damage but also reduce the transmission of vibration
to your hands. Prolonged exposure to vibration may cause numbness of the fingers
and other conditions.
•Wear sturdy and reasonably tall shoes with non-slip soles for greater stability. To
avoid injuries with the possible discarding of foreign objects by the cutting unit, do
not work with the device barefoot or in open shoes.
•To avoid damage to your hearing, it is recommended to use ear protectors or
earplugs while working with the trimmer.
SAFETY & WARNINGS
WARNING: Do not work with a trimmer under the influence of alcohol
or drugs or after using strong medicines.
WARNING: Always use protective glasses or gloves when working. It is
highly probable that solid objects or fragments of mowed stiff
vegetation are dropped into the face and eyes.
•Perform tank refuelling outdoors on the ground. Close the fuel cap tightly. Do not
refuel indoors.
•Fuel is highly flammable and explosive. Do not smoke, do not allow the presence
of sparks and flames in the fuel storage area and when the engine fuelling. Do not
refuel a hot engine. Shut off the engine before refuelling and make sure that it is
cold. The fuel tank may be under pressure. Carefully loosen the fuel cap first to
release any possible pressure and then remove it.
•Do not work with the trimmer if fuel was spilled during refuelling. Before starting,
carefully wipe the surface of the engine from accidentally spilled fuel and wait until
the remaining fuel evaporates. If fuel has been spilled, move the trimmer at least
three meters from the place of refuelling before starting the engine. Do not start
the engine if there is a smell of fuel.
•Do not store the unit with fuel in the tank. Fuel leakage may cause a fire. Avoid
contact with fuel. Irritations of the skin, the mucous membrane of the eyes, upper
respiratory tract or allergic reactions are possible with individual intolerance.
Frequent contact with fuel can lead to acute inflammation and chronic eczema.
Never start the engine indoors or in poorly ventilated areas. Never inhale exhaust
fumes. Exhaust gases contain carbon monoxide, which is colourless and odourless
and is very poisonous. Carbon monoxide in the respiratory system can cause loss
of consciousness or death. Do not start the engine if a malfunction of the ignition
system causes breakdown and sparking.
•Before starting the engine, make sure that the working bodies of the trimmer are
not in contact with foreign objects. Keep your hands and feet away from the
trimmer during engine start and operation. When working, always stand firm on
the ground, do not lose balance.
•Hold the trimmer with two hands; never attempt to work with one hand. Always
keep the working handles so that your fingers form a ring. Never work without the
protective cover of the trim coil.
•Do not lift the cutter above the knee level, as objects being thrown may fall into
the face or eyes.
•Take special care when changing direction, and when working in cramped
conditions (confined space). When working, approach the obstacle closely, but
never direct the cutting device inside or through the barrier. Hitting a trimmer cord
in a wire fence or a nylon mesh fence can cause pieces of wire, nets, and trimmer
cord to be dropped at high speeds in different directions.
•Do not touch the hot muffler and the cooling fins of the engine cylinder, as this can
cause serious burns. Do not work with the trimmer if the cylinder fins and muffler
are dirty.
•All maintenance and repair work should be carried out with the engine off.
•Keep the cutting device clean. Remove wound grass, branches, and foreign
objects from the trim coil and the trimmer gearbox.
•Turn off the trimmer immediately if abnormal vibration and/or noise occur. This
can be the result of serious damage to parts or components of the device, such as
a flywheel, a clutch, a cutting device, or a failure to correctly attach parts. Do not
make changes to the design of the device.
Transporting
The device can be transported by any type of closed transport in the original packaging or
without it, with the protection of the product from mechanical damage, precipitation, and
exposure to chemically active substances. During loading and unloading operations, the
device should not be exposed to shocks, falls and atmospheric precipitation.
Always ensure that the transport conditions include:
•Ambient air temperature from - 40 to + 40°C.
•Relative air humidity not more than 80% at 20°C.
When carrying the trimmer for short distances (when moving from one job to another) it is
recommended to stop the engine. Carry the trimmer on a belt, holding the handles. Avoid
contact with the muffler (there is a risk of burns) and combustible substances (risk of fire).
Usage
The petrol trimmer is used for cutting grass and small shrubs, and for operation under 5 to
35°C ambient temperature.
Using the trimmer for any other purpose and other than the above operating conditions
constitutes a violation of the conditions of safe operation.
To avoid injury to the user, damage to property or damage to equipment, do not use a
trimmer for:
•Cleaning the garden paths from debris,
•Chopping compost and cutting tree and shrub residues,
•Alignment of soil irregularities, cutting of hummocks on the surface of the earth,
•Drive for another working device,
•Driving various vehicles, including floating ones.
WARNING: The device is not intended for professional (commercial) use.
1
Starter handle
14
Throttle trigger
2
Starter
15
Throttle lock
3
Throttle valve control lever
16
Throttle lever
4
Plug cables
17
Pipe and engine connection
5
Fuel tank
18
Coil with nylon thread
6
Exhaust pipe
19
Lower gearbox
7
Grip
20
Protective cover
8
Engine casing
21
3T blade
9
Chainsaw
22
Double shoulder belt
10
Lower handle attachment
23
Mounting plate for the protective cover
11
Shoulder strap ring
24
Blade guard
12
Upper handle attachment
25
Hedge cutter
13
Power switch
OVERVIEW
Chainsaw
1
Tire
5
Gear housing
2
Chain
6
Bar cover
3
Oil tank
7
Rod
4
Oil cap
Hedge cutter
1
Blade covers
4
Handle
2
Blades
5
Latch lock
3
Gear housing
6
Rod
Handle installation
1. Place the device on a flat, hard, and clean surface. Unscrew the mounting collar
using a wrench. Place the handle over the bar and secure it with the mounting
clamp (Fig. 2). Tighten the screws.
2. Install the shoulder strap by inserting the hook into the clip (Fig. 3). Adjust the strap
to the desired length.
INSTALLATION
Screws
Mounting plate
Pipe
Shaft
Mounting plate
Fig. 3
Fig. 2
3. Install the protective cover on the bar, inserting it between the bracket and the
housing as shown below and fix it with four screws (Fig. 4).
4. Connect top and bottom so that the bottom spring button fits into the hole in the
top bar. If necessary, turn the coil shaft so that the drive shaft located at the
bottom of the rod engages with the counterpart at the top. Secure the connection
with the clamping screw of the rod.
5. Install the rod assembly to the engine using four screws (Fig. 5).
Nut
Washer
Mounting cup
Fig. 5
Fig. 4
Inhaltsverzeichnis
Andere Kogan Trimmer Handbücher
