Kohler K-14518 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucets

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-14518

115703-2-AB

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Pipe

Wrench Adjustable

Wrench Hacksaw or

Tube Cutter Plumbers

Putty

Thread

Sealant Channel Lock

Pliers

Pipe Sealant

115703-2-AB 2 Kohler Co.

1. Spout Installation

Apply a bead of plumbers putty or other sealant to the underside

of the spout or putty ring (if supplied) according to the putty

manufacturer’s instructions.

Locate the center hole and insert the spout.

Slide the metal washer and nut onto the spout shank.

Securely tighten the nut with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Nut

Washer

Dished

Washer

Apply

Plumbers

Putty

Kohler Co. 3 115703-2-AB

2. Handle Valve Installation

NOTE: The valve body marked ″Cold″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Insert the valve bodies into the proper mounting holes.

Apply a bead of plumbers putty or other sealant to the underside

of the escutcheons according to the putty manufacturer’s

instructions.

Install a washer and a nut onto the underside of each valve body.

Align the end bodies so the supply tubes ﬁt evenly into the valve

body outlets.

Rotate each valve body until the copper tubing faces towards the

outside of the lavatory.

While holding the valve bodies in place, securely tighten the

locknuts with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Gasket

Nut

Washer

Valve Body

115703-2-AB 4 Kohler Co.

3. Flexible Hose Installation

Thread a ﬂexible hose onto each handle valve outlet.

Securely tighten the hose with a wrench. Do not overtighten.

Connect the ﬂexible hoses to the supply tee. Do not use thread

sealant. To avoid kinking the hoses, loop them as shown. Securely

tighten the hose with a wrench. Do not overtighten.

Hose

O-Ring

End Body Outlet

End Body

Supply

Tee

Flexible

Hose

Kohler Co. 5 115703-2-AB

4. Drain Style

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

115703-2-AB 6 Kohler Co.

5. Drain Installation-Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply Plumbers

Putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

Kohler Co. 7 115703-2-AB

6. Complete Drain Installation-Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Faucet

Rod

Clip

Thumb

Screw

Link

115703-2-AB 8 Kohler Co.

7. Drain Installation-Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply Plumbers

Putty.

Flange

Gasket

Washer

Nut

Drain Body

Fixture

Kohler Co. 9 115703-2-AB

8. Complete Drain Installation-Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Hand

tighten the body nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, and thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Rod

Clip

Stopper

Nut

Flange

Seal

Nut

Tailpiece

Apply

Thread

Sealant.

Thumb

Screw

Stopper Rod

Link

115703-2-AB 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler BEITOU 72830T-L Bedienungsanleitung

Kohler

Kohler K-300 Montageanleitung

Kohler

Kohler K-7331 Montageanleitung

Kohler

Kohler K-16231 Montageanleitung

Kohler

Kohler K-1234 Bedienungsanleitung

Kohler

Kohler MAXISPACE 2.0 Bedienungsanleitung

Kohler

Kohler K-45765 Series Montageanleitung

Kohler

Kohler 12966T-C Bedienungsanleitung

Kohler

Kohler C3-050 Bedienungsanleitung

Kohler

Kohler K-895 Montageanleitung

Kohler

Kohler K-1118-LA Kurzanleitung

Kohler

Kohler K-842-H2 Montageanleitung

Kohler

Kohler K-14027 Bedienungsanleitung

Kohler

Kohler K-809 Kurzanleitung

Kohler

Kohler MATTIA K-36974T Bedienungsanleitung

Kohler

Kohler K-610 Montageanleitung

Kohler

Kohler K-T944-4 Montageanleitung

Kohler

Kohler ACCLIV 33088T-4-CP Bedienungsanleitung

Kohler

Kohler Mira Showers Elevate 2.1814.107 Bedienungsanleitung

Kohler

Kohler Underscore Cube Bedienungsanleitung

Kohler

Kohler K-4615 Bedienungsanleitung

Kohler

Kohler K-1224-HB Kurzanleitung

Kohler

Kohler 2273W Bedienungsanleitung

Kohler

Kohler K-2746T-1/8 Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung