Kohler K-16232 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-16232

1054191-2-A

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Plumbers

Putty Sealant

Tape Pipe

Sealant

1054191-2-A 2 Kohler Co.

1. Install the Spout

Apply a bead of plumbers putty or other sealant to the underside

of the spout base according to the putty manufacturer’s

instructions.

Locate the center hole and insert the spout.

Install the metal washer and nut.

Securely tighten the nut with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Remove and retain the guide tube nut and O-ring from the

supply tee.

Insert the washer and rubber gasket into the supply tee.

Thread the supply tee onto the spout until hand-tight.

Hold the spout in place and tighten the supply tee with a wrench

until it is aligned side to side. Do not overtighten.

Slip the O-ring over the lift rod and thread the guide tube nut

onto the supply tee.

Tighten the guide tube nut on the supply tee with a wrench. Do

not overtighten.

Nut

Washer

O-Ring

Apply

plumbers

putty.

Metal

Washer

Supply

Tee

Guide

Tube Nut

Spout

Lift Rod

Rubber

Gasket

Kohler Co. 3 1054191-2-A

2. Install the Valve Bodies

NOTE: The valve body marked ″COLD″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Apply a bead of plumbers putty or other sealant to the underside

of the base of the handle body according to the manufacturer’s

instructions.

From the top of the lavatory, insert the cold and hot valve bodies

into the mounting holes. Make sure that the body marked

″COLD″is installed in the right-hand hole as viewed from the

front of the lavatory.

Install a washer and a nut onto the underside of each valve body.

Rotate each valve body until the copper tubing faces toward the

outside of the lavatory.

While holding the valve bodies in place, securely tighten the nuts

with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Install the O-ring on the hose and thread each hose into the

handle body outlet.

Tighten the hose connections on the handle body with a wrench.

Do not overtighten.

Loop the hoses as shown and connect them to the supply tee

inlets. Do not use thread sealant. Do not overtighten.

Copper

Tube

Nut

Flexible

Hose

Washer

O-Ring

Handle

Body

Outlet

Supply

Tee

Flexible

Hose

Supply

Tee

Flexible

Hose

Supply

Tee

Flexible

Hose

Supply

Tee

Flexible

Hose

Supply

Tee

Flexible

Hose

1054191-2-A 4 Kohler Co.

3. Install the Drain

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Flat Washer

Nut

Drain Body

Fixture

Kohler Co. 5 1054191-2-A

4. Complete the Drain Installation

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, then thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Clip

Stopper

Stopper Nut

Flange

Seal

Rod Nut

Tailpiece

Apply

thread

sealant.

Thumb

Screw

Stopper

Rod

Link

Rod

Lift

Rod

1054191-2-A 6 Kohler Co.

5. Connect the Supplies

Install the lavatory using the lavatory manufacturer’s instructions.

Connect the supply tubes to the handle valve inlets, and to the

supply stops. Left is hot and right is cold.

Tighten all connections.

Supply

Tube

Valve

Inlet

Shut-off

Valve

Kohler Co. 7 1054191-2-A

6. Installation Checkout

Connect the tailpiece and P-trap (as needed).

Ensure that all connections are tight.

Remove the aerator by turning it counterclockwise.

Open the drain.

Turn on the main water supply and check for leaks. Adjust as

needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks. Turn the

faucet off.

Remove any debris from the aerator and reinstall.

Aerator

Spout

1054191-2-A 8 Kohler Co.

Guide d’installation

Robinet de lavabo à large entraxe

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Replacer les tubes d’alimentation ou d’évacuation si nécessaire.

Pour les nouvelles installations, installer le robinet avant

d’installer le lavabo.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Clé à molette Mastic de

plomberie Ruban

d'étanchéité Joint

d'étanchéité

Kohler Co. Français-1 1054191-2-A

1. Installer le bec

Appliquer un cordon de mastic d’étanchéité ou un produit

semblable sur le dessous de la base du bec verseur selon les

instructions du fabricant du mastic.

Localiser l’oriﬁce central et insérer le bec.

Installer la rondelle métallique et l’écrou.

Bien serrer l’écrou avec une clé. Ne pas trop serrer.

Retirer tout excédent de mastic de plombier ou de joint

d’étanchéité.

Retirer et conserver l’écrou du tube-guide et le joint torique du

manchon de T d’alimentation.

Insérer la rondelle et le joint d’étanchéité dans le T

d’alimentation.

Visser à la main le T d’alimentation sur la tige du bec jusqu’au

serrage à main.

Maintenir le bec en place et serrer le T d’alimentation avec une

clé jusqu’à ce qu’il soit aligné de côté à côté. Ne pas trop serrer.

Glisser un joint torique sur la tige de levage et visser l’écrou du

tube-guide sur le T d’alimentation.

Serrer l’écrou du tube-guide sur le T d’alimentation avec une clé.

Ne pas trop serrer.

Écrou

Rondelle

Joint torique

Appliquer du

mastic de

plomberie.

Rondelle

métallique

Écrou du

tube-guide

Bec

T d'alimentation Joint en

caoutchouc

Tige de

levage

1054191-2-A Français-2 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler Sonata K-1641 Bedienungsanleitung

Kohler

Kohler K-11050 Montageanleitung

Kohler

Kohler FAMILY CARE K-23205T Bedienungsanleitung

Kohler

Kohler K-895 Montageanleitung

Kohler

Kohler K-R99254X-4CD Montageanleitung

Kohler

Kohler K-28238-GKE Bedienungsanleitung

Kohler

Kohler K-792-H2 Montageanleitung

Kohler

Kohler QUICK-RELEASE QUIET-CLOSE K-17608T Bedienungsanleitung

Kohler

Kohler K-4637 Bedienungsanleitung

Kohler

Kohler K-7500 Bedienungsanleitung

Kohler

Kohler URBANITY 25717T-9 Bedienungsanleitung

Kohler

Kohler K-8502 Bedienungsanleitung

Kohler

Kohler ELEVATION 72679T-C7 Bedienungsanleitung

Kohler

Kohler ACCLIV 33088T-4-CP Bedienungsanleitung

Kohler

Kohler K-817 Bedienungsanleitung

Kohler

Kohler K-15996 Montageanleitung

Kohler

Kohler K-7223 Bedienungsanleitung

Kohler

Kohler K-671 Montageanleitung

Kohler

Kohler K-22261T Bedienungsanleitung

Kohler

Kohler ODEON 98963T-4 Bedienungsanleitung

Kohler

Kohler Mira Store Bedienungsanleitung

Kohler

Kohler K-701803T-FMSW Bedienungsanleitung

Kohler

Kohler TEND K-20713T-ER Bedienungsanleitung

Kohler

Kohler 10257T Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung