Kohler K-5250 Bedienungsanleitung

Installation Guide

Drinking Fountains

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-5250 K-5264

101024-2-AC

Tools and Materials

Before You Begin

CAUTION: Risk of personal injury. Handle with care.

Vitreous china can break or chip if the product is handled

carelessly.

Observe all local plumbing and building codes.

Plumbers

Putty Sealant

Tape Tube Cutter

Plus:

3/32" Hex

Wrench

• Various

Carpentry Tools

101024-2-AC 2 Kohler Co.

Roughing-In for K-5250

•The distance between the rim and the ﬂoor (dimension H) is 30″

(762 mm) for grade schools and 36″(914 mm) to 44″(1118 mm)

for other buildings.

19-1/2" (495 mm)

2-5/8"

(67 mm)

Floor

1/2" (13 mm) x

1" (25 mm)

Anchor Slot

8-1/2" (216 mm)

5" (127 mm) 3-1/2"

(89 mm)

7-1/4"

(184 mm)

1-5/8"

(41 mm)

3/8" NPT

Supply

2-1/4"

(57 mm)

3" (76 mm)

2-1/8"

(54 mm)

1-1/4" NPT Tap

4-5/8"

(117 mm) 12-3/8"

(314 mm)

15-3/8" (391 mm)

5-3/8"

(137 mm)

Kohler Co. 3 101024-2-AC

Roughing-In for K-5264

•The distance between the rim and the ﬂoor (dimension H) is 30″

(762 mm) for grade schools and 36″(914 mm) to 44″(1118 mm)

for other buildings.

1. Prepare the Site

NOTE: Be sure to install sufficient backing to support the wall

hangers and anchor bolt.

Rough-in the supply and drain piping according to the

roughing-in.

Temporarily install a capped length of 1-1/4″and 3/8″pipe to

the drain and supply to extend a minimum of 2″(51 mm) beyond

the ﬁnished wall.

Floor

3-1/4"

(83 mm)

(76 mm)

3-3/8" (86 mm)

Ø 7/16" (11 mm)

Anchor Screw Hole in Back

4" (102 mm)

7/8"

(22 mm)

3/8" NPT

Supply

9-1/4"

(235 mm)

(152 mm)

3-1/4"

(83 mm)

2-1/2" (64 mm)

13" (330 mm)

13"

(330 mm)

1-1/4" NPT Tap

(127 mm)

14" (356 mm)

4-5/8"

(117 mm)

101024-2-AC 4 Kohler Co.

2. Install the Drain

Remove the temporary 3/8″pipe previously installed into the

supply ﬁtting.

Remove the 1-1/4″pipe installed to the drain ﬁtting.

Install a 3/8″nipple for the supply to extend approximately

7/16″(11 mm) from the ﬁnished wall.

NOTE: If the tubing is used for supply, a male threaded adapter

must extend approximately 7/16″(11 mm) from the ﬁnished wall.

Assemble the water stop onto the nipple.

Ensure that the screwdriver slot on the water stop is angled at

45°, and that it is facing toward the bottom access.

Ensure that the water stop inlet and outlet are parallel to the

ﬂoor.

3. Install the Drinking Fountain

Measure the distance between the ﬁnished wall and the center of

the drinking fountain outlet.

Remove the temporary capped nipple.

Replace the temporary nipple with a nipple that will position the

trap inlet directly under the drinking fountain outlet.

Install the two provided wall hangers to the wall, as shown in the

roughing-in diagram. Secure the hangers by the center hole only.

Hanger

Ferrule

Nut

1-1/4" Drain

3/8" Supply

Stop Assembly

(Turn to 45˚ angle for access.)

Supply Tube

Control Valve

Kohler Co. 5 101024-2-AC

Install the Drinking Fountain (cont.)

Install the trap to the nipple. Position and level the fountain onto

the hangers.

NOTE: The hangers may have to be repositioned. Due to

dimensional variations with vitreous china products, the hangers

may have to be raised or lowered slightly so that there is 3/16″(5

mm) from the bottom of the drinking fountain outlet to the face of

the trap inlet.

Using screws, secure the two hangers to the backing through the

remaining two holes in the hanger.

Through the side access, mark the center of the 1/2″(13 mm) x 1″

(25 mm) anchoring slot located on the right-hand back wall of the

fountain.

Remove the fountain from the hangers and install the anchoring

stud.

NOTE: The machine threaded portion of the anchoring stud should

extend approximately 5/8″(16 mm) from the ﬁnished wall. The stud

must be centered in the slot.

4. Install the Strainer

Apply a bead of plumbers putty or other sealant around the

underside of the strainer body ﬂange according to the

manufacturer’s instructions.

Insert the strainer body into the fountain drain hole.

From the underside of the drinking fountain, slide the tapered

gasket onto the strainer body, making sure that the tapered side is

facing up.

Position the fountain onto the hangers so that the anchoring stud

and the opening of the slot line up.

Line up the strainer body with the trap, and thread the strainer

body securely onto the trap.

NOTE: The fountain must be supported by the hangers only. Do

not position the drain after it has been tightened into the trap, or the

seal may be broken.

101024-2-AC 6 Kohler Co.

5. Secure the Fixture

CAUTION: Risk of personal injury. Overtightening can cause

vitreous china to break or chip.

Place the washer and cap nut over the anchoring stud, and

carefully tighten to secure the drinking fountain.

From the bottom of the access, install the copper supply tube

with the compression ﬁtting between the stop and control valve.

Connect the straight end of the tube to the stop, then connect the

angled end of the supply tube to the control valve until both are

hand-tight.

Secure both nuts with a wrench.

NOTE: The copper supply connection may be bent slightly to ﬁt.

Snap the strainer plate into the strainer body. If necessary, adjust

the drinking fountain head so that the arc of the water is parallel

to the wall.

6. Install the Cover Plates

Check for leaks.

Install the cover plates to the bottom access openings.

Kohler Co. 7 101024-2-AC

7. Complete the Installation

When this drinking fountain is installed with a water cooler, jam

the knurled locknut against the bonnet assembly to prevent

continuous ﬂow.

The lever handle has been adjusted at the factory so that the

blade is parallel to the ﬂoor. If additional adjustment is required,

remove the setscrew with a 3/32″hex wrench.

Pull the handle straight off. Do not twist the handle.

Reverse this procedure to reinstall the handle.

Bonnet

Assembly

Knurled

Locknut

Setscrew

101024-2-AC 8 Kohler Co.

Guide d’installation

Fontaines à eau potable

Outils et matériaux

Avant de commencer

ATTENTION: Risque de blessures. Manipuler avec

précaution. La porcelaine vitriﬁée peut se briser ou se fendre

si le produit est manipulé avec négligence.

Respecter tous les codes de plomberie et de bâtiment locaux.

Ruban

d'étanchéité Coupe-tubes

Plus:

Clé hexagonale

de 3/32"

• Outils Variés de

charpenterie

Mastic de

plombier

Kohler Co. Français-1 101024-2-AC

Raccordement pour K-5250

•La distance entre le rebord et le sol (dimension H) est de 30″(762

mm) pour les écoles primaires et est comprise entre 36″(914 mm)

et 44″(1118 mm) pour les autres bâtiments.

Filetage 1/-1/4" NPT

Sol

Alimentation

3/8" NPT

2-5/8"

(67 mm)

8-1/2" (216 mm)

5" (127 mm) 3-1/2"

(89 mm)

7-1/4"

(184 mm)

1-5/8"

(41 mm)

2-1/4"

(57 mm)

3" (76 mm)

2-1/8"

(54 mm)

4-5/8"

(117 mm)

15-3/8" (391 mm)

5-3/8"

(137 mm)

19-1/2" (495 mm)

12-3/8"

(314 mm)

Rainure d'ancrage

de 1/2" (13 mm) x

1" (25 mm)

101024-2-AC Français-2 Kohler Co.

Andere Handbücher für K-5250

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler ENGLEFIELD K-78221X Montageanleitung

Kohler

Kohler K-45427 Montageanleitung

Kohler

Kohler K-792 Kurzanleitung

Kohler

Kohler STRAYT 37337M Bedienungsanleitung

Kohler

Kohler K-8052 Montageanleitung

Kohler

Kohler K-T10340 Montageanleitung

Kohler

Kohler Iron Works K-7103 Montageanleitung

Kohler

Kohler K-2075 Montageanleitung

Kohler

Kohler K-3387 Bedienungsanleitung

Kohler

Kohler K-11370 Montageanleitung

Kohler

Kohler K-1234 Bedienungsanleitung

Kohler

Kohler SKYLINE K-705880T-FM-SHP Bedienungsanleitung

Kohler

Kohler K-15815 Bedienungsanleitung

Kohler

Kohler Stillness K-960-4 Montageanleitung

Kohler

Kohler K-99257X-4CD Montageanleitung

Kohler

Kohler riverbath K-1397 Montageanleitung

Kohler

Kohler K-16280 Montageanleitung

Kohler

Kohler Tresham K-2992-8 Bedienungsanleitung

Kohler

Kohler STATEMENT K-26291T-CP Bedienungsanleitung

Kohler

Kohler HARKEN K-78197T Bedienungsanleitung

Kohler

Kohler NEW PURIST K-701574T Bedienungsanleitung

Kohler

Kohler K-T8224 Bedienungsanleitung

Kohler

Kohler K-2210 Montageanleitung

Kohler

Kohler K-T944-4 Montageanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung