Kohler Vanity K-2604 Montageanleitung

Installation and Care

Guide

Vanity

K-2604, K-5288, K-5289

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1267640-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length to clear

obstacles in the wall and 5/16″washers. Calculate proper lag

bolt length by adding the following: 1-1/2″(38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of product damage. Do not modify the vanity.

Doing so will compromise structural stability.

IMPORTANT! Risk of product damage. Use care when moving the

vanity to avoid impacting, sliding, or side-loading the legs.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the ﬁnish of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

Plus:

• Wood Screws

• 2x6s

• 5/16" Lag Bolts and Washers

[Min 250 lb (113.4 kg) Load Bearing]

• Socket Wrenches

• Siliconized Acrylic Caulk

1267640-2-A 2 Kohler Co.

1. Prepare the Site

NOTICE: If the K-2607 bridge cabinet will also be installed, extend

the backing material a minimum of 12″(305 mm) beyond the width

of the vanity on the side where the bridge will be installed.

NOTICE: To properly secure the vanity, the top of the required 2x6

backing material must be 32-1/2″(826 mm) from the ﬁnished ﬂoor.

Measure and mark 32-1/2″(826 mm) up from the ﬁnished ﬂoor.

This will be the height from the ﬁnished ﬂoor to the top of the

2x6 backing material.

Ensure there are no obstructions in the wall (such as wiring or

plumbing) from the marked height down to the ﬂoor. If there are

obstructions, select another area to install the vanity.

NOTICE: Extend the backing material beyond the width of the

vanity to the nearest stud to ensure proper support for the vanity.

Front-notch the studs 1-1/2″(38 mm) to ensure the 2x6 backing

material is ﬂush against the studs.

Secure the 2x6 backing material to the studs with framing nails.

Rough-in the water supply and drain lines into the rough-in

plumbing area of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

2x6

Backing

Material

32-1/2" (826 mm)

Kohler Co. 3 1267640-2-A

Prepare the Site (cont.)

Complete the ﬁnished wall. Make sure the ﬁnished wall is

straight and plumb, and the ﬂoor is ﬂat and perpendicular to the

ﬁnished wall.

1267640-2-A 4 Kohler Co.

2. Secure the Vanity

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length to clear

obstacles in the wall and 5/16″washers. Calculate proper lag

bolt length by adding the following: 1-1/2″(38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of product damage. Use care when moving the

vanity to avoid impacting, sliding, or side-loading the legs.

With assistance, lift and place the vanity in position against the

ﬁnished wall. Do not drag the vanity into position.

Verify the vanity is level and the back rail is plumb against the

wall. If necessary, turn the leveler(s) to adjust the unit.

Using a 1/4″drill bit, drill pilot holes through the back rail and

the ﬁnished wall. Verify the pilot holes are positioned to ensure

the lag bolts will engage the 2x6 backing material.

Secure the vanity to the wall with two 5/16″lag bolts and

washers (not provided).

Install the Bridge Cabinet (Optional)

Refer to the installation instructions packed with the K-2607

bridge cabinet.

Pilot

Hole

Finished

Wall

Washer

Lag Bolt

Back Rail

Leveler

Kohler Co. 5 1267640-2-A

3. Install the Bathroom Sink

CAUTION: Risk of personal injury. Vitreous china sinks are

very heavy. Get help lifting and aligning the sink.

Install the faucet (if applicable) and drain to the sink. Refer to the

faucet and drain manufacturer’s installation instructions.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the vanity ﬁnish.

Run a 1/4″(6 mm) continuous bead of siliconized acrylic caulk

around the top of the vanity, as illustrated.

NOTE: The sink is properly positioned when: (1) the back edge of

the sink is ﬂush against the ﬁnished wall and (2) the overhang on

the left, right, and front side of the sink is equal on each side of the

vanity.

With assistance, lift and properly position the sink on top of the

vanity.

Immediately wipe away any excess caulk that contacts the vanity.

Run a 1/8″(3 mm) bead of siliconized acrylic caulk along the top

edge of the sink where it contacts the ﬁnished wall.

Finished

Wall

1267640-2-A 6 Kohler Co.

4. Reverse Door Swing

(Optional - 24″only)

NOTE: To ease installation, get assistance supporting the door.

NOTE: The vanity comes with hinges installed on the inside left. To

reverse the door swing, use the included template (1181754-7) to

mount the brackets to the opposite side of the vanity.

Align the hinge hooks with the cup of the top bracket.

Slide the hinge onto the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Hook

Bracket

Cup

Kohler Co. 7 1267640-2-A

5. Adjust the Drawers

Remove

Slide the drawer out until fully extended.

From underneath, pull the release latches toward the center of the

drawer.

Lift the front of the drawer and pull toward you to disengage

from the rails.

Once removed, lay the drawer on a ﬂat, protective surface.

Reinstall

Fully extend the rails.

Align the holes in the back of the drawer with the rail hooks.

Rotate the drawer down onto the rails, engaging the front drawer

holes with the rail pins.

From underneath, push the release latches into the rails to secure

the drawer.

Latch

Rail

Hook

Holes

1267640-2-A 8 Kohler Co.

6. Recommended Hardware Placement

Measure and mark the dimensions for the hardware as shown

above.

Drill a 3/16″(21 mm) pilot hole at each marking.

Drill a ﬁnished hole to size.

Insert a screw through each hole. Thread the knob onto the screw.

24” Vanity Installation

From the back side of the door, insert the screw through the

predrilled hole.

Thread the knob onto the screw. Tighten securely.

Repeat for the drawer.

K-5288: 6-1/16" (154 mm)

K-5289: 4-9/16" (116 mm)

4-3/4"

(121 mm)

(25 mm)

Kohler Co. 9 1267640-2-A

Adjust the Door

Adjust

Refer to the illustration and note the screwdriver location for the

desired adjustment.

Remove

Apply a small amount of leverage to the door with one hand to

keep the door in the full open position.

With the other hand, press the clip to release the lower hinge

latch from the bracket.

Repeat for the upper hinge.

Move the door forward to slide the hinges off the brackets.

Reinstall

Apply a small amount of leverage to the door with one hand to

keep the door in the full open position.

With the other hand, align the top hinge with the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Open and close the door to ensure proper operation.

Care and Cleaning

Vitreous China and Fireclay

•Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

Adjustments

Side

Depth

Height

Bracket

Clip

1267640-2-A 10 Kohler Co.

Andere Handbücher für Vanity K-2604

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badezimmerarmatur Handbücher

Kohler

Kohler STRAYT 37337M Bedienungsanleitung

Kohler

Kohler K-24985K Montageanleitung

Kohler

Kohler STERLING Bedienungsanleitung

Kohler

Kohler K-3048 Bedienungsanleitung

Kohler

Kohler K-1805 Kurzanleitung

Kohler

Kohler ENGLEFIELD MILANO Bedienungsanleitung

Kohler

Kohler K-2392 Montageanleitung

Kohler

Kohler Stillness 954M-4 Bedienungsanleitung

Kohler

Kohler K-9033 Montageanleitung

Kohler

Kohler Converge K-R77634 Bedienungsanleitung

Kohler

Kohler Toobi K-T8975 Montageanleitung

Kohler

Kohler K-4643 Bedienungsanleitung

Kohler

Kohler K-31500X Montageanleitung

Kohler

Kohler K-223 Montageanleitung

Kohler

Kohler Englefield Valencia Elite Bedienungsanleitung

Kohler

Kohler K-8360-BN Montageanleitung

Kohler

Kohler MasterShower K-8520 Bedienungsanleitung

Kohler

Kohler K-15894 Bedienungsanleitung

Kohler

Kohler Mira Advance 8.7 Bedienungsanleitung

Kohler

Kohler K-4637 Bedienungsanleitung

Kohler

Kohler URBANITY 25717T-9 Bedienungsanleitung

Kohler

Kohler K-14418 Bedienungsanleitung

Kohler

Kohler K-6236 Montageanleitung

Kohler

Kohler K-108 Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

baliv

baliv DUK-80.30 T Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung

GRE

GRE DSALC32W Bedienungsanleitung