Kohler K-1106 Bedienungsanleitung

Installation Guide

Flanged 120 V Bath Whirlpool

K-1106, K-1112, K-1114,

K-1126, K-1131, K-1139,

K-1144, K-1154, K-1157,

K-1160, K-1192, K-1194,

K-1196, K-1198, K-1209,

K-1224, K-1239, K-1244,

K-1257, K-1266, K-1458,

K-1630, K-1635

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(e.j. K-12345M)

Français, page “Français-1”

Español, pagina “Español-1”

1011092-2-E

Important Information

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

Building materials and wiring should be routed away from the pump body and other heat-producing

components of the unit.

Install to permit access for servicing.

Grounding is required. The unit should be installed by a qualiﬁed service representative, and grounded.

WARNING: Risk of electric shock. A licensed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following requirements.

NOTICE: Follow all local plumbing and electrical codes.

Product Information

Electrical Requirements

The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device

(RCD). The GFCI or RCD protects against line-to-ground shock hazard. Use a 120 V, 15 A, 60 Hz dedicated

service for the whirlpool.

″H″models require a separate 120 V, 15 A, 60 Hz dedicated service for the heater.

NOTE: If the pump supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualiﬁed persons in order to avoid a hazard. The heater supply cord cannot be replaced. If the

cord is damaged the heater should be scrapped.

Product Notices

WARNING: Unauthorized modiﬁcation may cause unsafe operation and poor performance of the

whirlpool. Do not relocate the whirlpool pump, or make other modiﬁcations to the whirlpool

system, as this could adversely affect the performance and safe operation of the whirlpool. Kohler

Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any

such unauthorized modiﬁcation.

WARNING: Risk of electrical shock. Disconnect power before servicing.

WARNING: Risk of electrical shock. A licensed electrician should make all electrical connections.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation.

NOTICE: Follow all local plumbing and electrical codes.

Factory-Assembled Features

Factory installed components include pump with power supply cord and air switch transmitter. No

installation is needed.

″H″models are also supplied with a factory assembled heater.

An optional timer kit is available for certain models.

The whirlpool pump and piping are factory-assembled.

1011092-2-E 2 Kohler Co.

Important Information (cont.)

Connections and Service Access

Before installation, ensure proper access to the ﬁnal connections.

NOTICE: Provide unrestricted service access to the pump. You must provide access for servicing the

pump and controls. The access must be located immediately next to the pump. Study the roughing-in

information packed with the whirlpool.

Table of Contents

Important Information .............................................................. 2

Thank You For Choosing Kohler Company .............................................. 4

Tools and Materials ............................................................... 4

Before You Begin ................................................................. 5

Prepare the Site ................................................................. 6

Prepare the Whirlpool ............................................................. 7

Secure the Whirlpool — Models With Support Blocks ...................................... 8

Secure the Whirlpool — Models With Whirlpool Base ...................................... 9

Secure the Whirlpool to the Stud Framing .............................................. 10

Cut the Pump Banding Straps ...................................................... 10

Install the Plumbing .............................................................. 10

Make Electrical Connections ........................................................ 11

Test Run the Whirlpool ............................................................ 12

Complete the Finished Wall ........................................................ 13

Removing the Apron .............................................................. 13

Clean-Up After Installation ......................................................... 13

Conﬁrm Proper Operation .......................................................... 14

Troubleshooting Procedure ......................................................... 15

Kohler Co. 3 1011092-2-E

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Company. Your Kohler Company product reﬂects the true passion for design,

craftsmanship, artistry, and innovation Kohler Company stands for. We are conﬁdent its dependability and

beauty will surpass your highest expectations, satisfying you for years to come.

All the information in this guide is based upon the latest product information available at the time of

publication. At Kohler Company, we strive to fulﬁll our mission of improving the level of gracious living for

each person who is touched by our products and services. We reserve the right to make changes in product

characteristics, packaging, or availability at any time without notice.

Please take a few minutes to review this guide. If you encounter any installation or performance problems,

please call 1-800-4KOHLER (1-800-456-4537) from within the USA and Canada, or 001-877-680-1310 from

within Mexico.

Tools and Materials

Silicone Sealant Pencil

Level

Safety Glasses

Tape Measure

Pipe Wrench

Plus:

• Conventional woodworking tools

and materials

• Drop Cloth

• Construction adhesive (optional)

• Cement or mortar (optional)

• 2x4s or 2x6s

• Screws or Lag Bolts

1011092-2-E 4 Kohler Co.

Before You Begin

NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural

support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool.

NOTICE: Do not support the load weight of the whirlpool by the perimeter of the rim. The rim perimeter

must be adequately supported, but must not support the load weight of the whirlpool.

For whirlpools without an apron, a drop-in installation is necessary. For whirlpools with integral or

optional apron, an alcove or corner installation is recommended, depending upon the model chosen.

Inspect the whirlpool for damage before you begin installation.

You must install this whirlpool to an adequately supported, level subﬂoor.

Conﬁrm adequate mounting and connection space for the faucet speciﬁed for your installation.

For corner units with integral apron: Have a qualiﬁed electrician install the outlets for the pump

and heater (if used) at the speciﬁed location on the whirlpool. Refer to the above illustration.

Kohler Co. reserves the right to make revisions in the design of products without notice, as speciﬁed

in the Price Book.

Install the outlets for

the pump and heater

(if used) to the

mounting plate.

Outlet

Kohler Co. 5 1011092-2-E

1. Prepare the Site

NOTICE: Refer to the Roughing-in Guide packed with your bath whirlpool for the required minimum

lb/square foot (kg/square meter) ﬂoor support.

NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural

support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool.

NOTICE: Do not support the load weight of the whirlpool by the perimeter of the rim. The rim perimeter

must be adequately supported, but must not support the load weight of the whirlpool.

Make sure the ﬂooring offers adequate support for your whirlpool, and verify that the subﬂoor is

ﬂat and level.

For Whirlpools without Apron:

NOTICE: The whirlpool should be installed in a drop-in installation.

Construct 2x4 or 2x6 stud framing for your installation.

NOTICE: When planning the construction of the site, take into consideration that the whirlpool must be

supported by its feet or base to avoid product damage. Do not support the load weight of the whirlpool

by the perimeter of the rim. The rim perimeter must be adequately supported, but must not support the

load weight of the whirlpool. This includes whirlpools placed in alcove installations.

For a raised installation: Frame the ﬂoor or construct a frame in accordance with the roughing-in

information packed with the whirlpool.

Carefully lay out and cut the rough deck material. Use the cut-out template if one is provided, or

refer to the roughing-in cut-out information.

For Whirlpools with Integral or Optional Apron:

The whirlpool should be installed in an alcove or corner installation, depending upon the model

chosen. Construct 2x4 or 2x6 stud framing designed for your particular installation. Construct a

frame in accordance with the roughing-in information packed with the whirlpool.

For All Installations:

Position the plumbing according to the roughing-in information packed. Cap the supplies, and

check for leaks.

Frame the floor

according to the

roughing-in information.

Position the rough

plumbing.

Construct 2x4 or 2x6

tud framing according

to the roughing-in

information. Verify that the subfloor

offers adequate support,

and is flat and level.

Construct 2x4 or

2x6 stud framing

according to the

roughing-in

information.

Position the

rough plumbing.

Verify that the subfloor

offers adequate support,

and is flat and level.

1011092-2-E 6 Kohler Co.

2. Prepare the Whirlpool

Install the drain to the whirlpool according to the drain manufacturer’s instructions. Do not connect

the trap at this time.

Position a clean drop cloth or similar material in the bottom of the whirlpool. Be careful not to

scratch the surface of the whirlpool.

Kohler Co. 7 1011092-2-E

3. Secure the Whirlpool — Models With Support Blocks

NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural

support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool.

NOTICE: Do not support the load weight of the whirlpool by the perimeter of the rim. The rim perimeter

must be adequately supported, but must not support the load weight of the whirlpool.

If the subﬂoor is not level, shim the whirlpool support blocks as necessary.

Choose the installation option that best applies to your particular installation. Follow the appropriate

instructions.

Option Using a Cement or Mortar Bed

NOTE: Do not use gypsum cement or drywall compound for this application, as they will not provide an

acceptable, durable bond.

NOTE: The pump support bracket (when the pump banding straps are cut) and support blocks must

rest directly on the subﬂoor.

Spread a 2″(5.1 cm) thick layer of cement or mortar on the subﬂoor where the whirlpool will be set.

This will help secure, level, and support the unit. Clear all the material away from the pump

support bracket and support block locations.

Position a piece of plastic drop cloth material on top of the cement or mortar bed. With help,

carefully lift the whirlpool into place, and make sure the pump support bracket and support blocks

do not rest in the bed material.

Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting on all support

blocks.

Option Using Construction Adhesive

Apply a generous amount of high-quality construction adhesive to the bottom of the support blocks.

With help, carefully lift the whirlpool into position.

Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting on all support

blocks.

Clear space for pump.

Spread a 2" (5.1 cm) layer of

cement or mortar bed material.

Clear spaces for

support blocks.

Apply construction adhesive

to the support blocks.

1011092-2-E 8 Kohler Co.

4. Secure the Whirlpool — Models With Whirlpool Base

NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural

support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool.

NOTICE: Do not support the load weight of the whirlpool by the perimeter of the rim. The rim perimeter

must be adequately supported, but must not support the load weight of the whirlpool.

Choose the installation option that best applies to your particular installation. Follow the appropriate

instructions.

If the subﬂoor is not level, shim the whirlpool base as necessary.

Option Using a Cement or Mortar Bed

NOTE: Do not use gypsum cement or drywall compound for this application, as they will not provide an

acceptable, durable bond.

Spread a 2″(5.1 cm) thick layer of cement or mortar on the subﬂoor where the whirlpool will be set.

This will help secure, level, and support the unit.

Position a piece of plastic drop cloth material on top of the cement or mortar bed. With help,

carefully lift the whirlpool into place.

Insert the drain tailpiece into the trap. Make sure the whirlpool is level. Use screws or lag bolts (not

provided) to secure the whirlpool base to the ﬂoor. Drill small pilot holes through the whirlpool

base as needed.

Option Using Construction Adhesive

Apply a generous amount of high-quality construction adhesive to the bottom of the whirlpool base.

With help, carefully lift the whirlpool into position.

Insert the drain tailpiece into the trap. Make sure the whirlpool is level. Use screws or lag bolts (not

provided) to secure the whirlpool base to the ﬂoor. Drill small pilot holes through the whirlpool

base as needed.

Spread a 2" (5.1 cm) layer of

cement or mortar bed material.

Apply construction adhesive

to the whirlpool base.

Kohler Co. 9 1011092-2-E

5. Secure the Whirlpool to the Stud Framing

Drill a small pilot hole through the nailing-in ﬂange at each stud. Add shims between the nailing-in

ﬂange and the studs as needed to eliminate gaps.

Nail 1/4″(6 mm) thick furring strips to the studs to shim out to the edge of the nailing-in ﬂange.

Use #6 large-head galvanized nails to secure the nailing-in ﬂange to the studs.

6. Cut the Pump Banding Straps

IMPORTANT! This step is necessary to make your Kohler whirlpool operate more quietly.

NOTE: Do not raise the pump higher than it was before you cut the pump banding straps. If the pump is

raised too high, it will not prime properly.

Use tin snips to cut the two pump banding straps. When the banding straps are cut, the pump

support bracket and pump will drop about 1/2″(1.3 cm) until they rest on the subﬂoor. If the pump

drops more than 1/2″(1.3 cm), shim under the pump support bracket so there is a 1/2″(1.3 cm)

gap between the pump and bracket to allow for proper drainage.

To minimize whirlpool noise and vibration, be sure the pump is not in direct contact with the

shipping bracket after the pump banding straps are cut.

Secure the pump support bracket to the subﬂoor with screws or lag bolts (not provided).

7. Install the Plumbing

CAUTION: Risk of property damage. A watertight seal must exist on the whirlpool drain. The

watertight seal will prevent property damage.

Connect the drain to the trap according to the drain manufacturer’s instructions.

Install the faucet valving according to the faucet manufacturer’s instructions. Do not install the

faucet trim until instructed. Open the hot and cold water supplies, and check the supply

connections for leakage.

Run water into the whirlpool, and check the drain connections for leakage.

Stud

Nail 1/4" (6 mm)

thick furring strips

to the studs.

Drill a small hole

through the nailing-in

flange at each stud.

Use #6 large-head

galvanized nails to secure

the nailing-in flange to the

studs.

Drainage Suction Line

Pump

Cut the pump

banding straps.

NOTE:

Pump model illustrated may differ from your

actual product.

1011092-2-E 10 Kohler Co.

Andere Handbücher für K-1106

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Badewanne Handbücher

Kohler

Kohler Memoirs K-723 Kurzanleitung

Kohler

Kohler Eternity K-1522-ET Bedienungsanleitung

Kohler

Kohler Sterling Unwind 96129-0 Bedienungsanleitung

Kohler

Kohler K-1315 Bedienungsanleitung

Kohler

Kohler Archer K-1125-LA Kurzanleitung

Kohler

Kohler K-1822 Montageanleitung

Kohler

Kohler K-713 Kurzanleitung

Kohler

Kohler K-855 Kurzanleitung

Kohler

Kohler K-14037 Montageanleitung

Kohler

Kohler Freewill K-12105-H Bedienungsanleitung

Kohler

Kohler Underscore K-1822-GVB Bedienungsanleitung

Kohler

Kohler Birthday Bath K-100 Montageanleitung

Kohler

Kohler Archer K-1122-GLAW Bedienungsanleitung

Kohler

Kohler K-1226-CD Kurzanleitung

Kohler

Kohler K-1124 Bedienungsanleitung

Kohler

Kohler K-1394-H2 Montageanleitung

Kohler

Kohler K-99023T Bedienungsanleitung

Kohler

Kohler K-1166-C1 Montageanleitung

Kohler

Kohler K-11343 Kurzanleitung

Kohler

Kohler K-1114 Kurzanleitung

Kohler

Kohler K-1109-LA Kurzanleitung

Kohler

Kohler Archer K-1949-GHRAW Bedienungsanleitung

Kohler

Kohler K-1146-H Kurzanleitung

Kohler

Kohler K-1162-H Kurzanleitung

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard Colony 5-1/2' x 32" Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kallista

Kallista P50045-G5 Montageanleitung

Ariel

Ariel AM Series Bedienungsanleitung

Agua

Agua BAHLI-60 Bedienungsanleitung

DURAVIT

DURAVIT XViu 700443 Bedienungsanleitung

American Standard

American Standard Colony 2740 Series Bedienungsanleitung

Rapsel

Rapsel OFURO Handbuch