Kohler K-407 Bedienungsanleitung

Installation Guide

Wall Mount Transfer Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-407

088037-2-B

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

Do not remove the plaster guard from the transfer valve until

instructed to do so.

For proper trim ﬁt, the ﬁnished wall must align within the 11/16″

(1.7 cm) front-to-back depth of the installed plaster guard.

The roughing-in depth minimum = 3″(7.6 cm); maximum =

3-7/8″(9.8 cm).

A mixed water supply is required for this transfer valve.

Do not plug any outlets on this transfer valve. The transfer valve

is not intended to be used as a shut-off valve.

If less than three accessories will be installed, connect the unused

transfer valve port to one of the accessories. All outlet ports must

be connected to an accessory, even if one accessory is connected

to two transfer valve outlet ports.

If you install this transfer valve to the shower port of your

mixing valve, the performance of the valve will be reduced.

Do not use plastic pipe for transfer valve connections.

Adjustable

Wrench Pencil

Tape

Measure Phillips

Screwdriver

088037-2-B 2 Kohler Co.

Before You Begin (cont.)

Carefully plan the installation before beginning. Carefully read

the entire instructions. Component location, spacing, and

situational requirements can vary.

Shut off the main water supply.

Inspect the waste and supply tubing; replace if necessary.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Kohler Co. 3 088037-2-B

1. Prepare the Valve

Thin Wall Installation

NOTE: The plaster guard may be installed behind the wall to add

stability, but front servicing of the transfer valve will no longer be

possible. You will need to provide rear access to the valve.

Provide a 3″(7.6 cm) diameter hole in the wall material.

Thick Wall Installation

Provide a 3-3/4″(9.5 cm) to 3-7/8″(9.8 cm) diameter hole in the

wall material.

For All Installations

Attach the plaster guard to the cartridge sleeve and stem

assembly using the two escutcheon screws in the holes labeled for

your application.

Thick Wall

Thin Wall

(7.6 cm)

3-3/4" (9.5 cm) to

3-7/8" (9.8 cm)

Thick

Wall

Holes

Plaster

Guard

Thin

Wall

Holes

088037-2-B 4 Kohler Co.

2. Install the Valve

CAUTION: Risk of product damage. Do not apply direct heat to

the transfer valve body. Excessive heat will damage the plastic

valve components and the plaster guard.

Install 1/2″copper hot and cold water supplies and connect them

to your mixing valve according to the manufacturer’s instructions.

NOTE: Do not install the transfer valve upside down.

Route the 1/2″mixed water supply line to the transfer valve inlet

port location.

Solder the mixed water supply line to the transfer valve inlet

port.

Plaster

Guard

1/2" Mixed

Supply Inlet

Finished

Wall

Kohler Co. 5 088037-2-B

3. Install the Piping

For Three Way Applications:

Install 1/2″copper tubing or 1/2″piping for all accessories.

Securely fasten the piping and outlet ells to the framing.

Install temporary 1/2″nipples in the outlet ells so they extend a

minimum of 2″(5.1 cm) beyond the planned ﬁnished wall.

Turn on the water supply to the transfer valve and check the

transfer valve for proper operation and leakage. Once everything

is veriﬁed, turn off the water.

For Two Way Applications:

IMPORTANT! Do not plug any outlets on this transfer valve. The

transfer valve is not intended to be used as a shut-off valve. If less

than three accessories will be installed, connect the unused transfer

valve port to one of the accessories. All outlet ports must be

connected to an accessory, even if one accessory is connected to two

transfer valve outlet ports.

Install 1/2″copper tubing or 1/2″piping for both accessories.

Use a tee to connect two of the outlet ports. Securely fasten the

piping and outlet ells to the framing.

Install temporary 1/2″nipples in the outlet ells so they extend a

minimum of 2″(5.1 cm) beyond the planned ﬁnished wall.

Accessory “A”

Water Line

Accessory “B”

Water Line

Mixed Water Supply

1/2" Copper Tubing

or Piping Mixed Water Supply 1/2"

Copper Tubing or Piping

Accessory Water

Lines 1/2" Copper

Tubing or Piping

088037-2-B 6 Kohler Co.

Install the Piping (cont.)

Turn on the water supply to the transfer valve and check the

transfer valve for proper operation and leakage. Once everything

is veriﬁed, turn off the water.

Kohler Co. 7 088037-2-B

4. Complete the Valve Installation

For All Applications:

Install caps on the temporary bath and shower nipples. Turn on

the water and check for leaks. Once no leakage is veriﬁed, turn

off the water.

Complete the ﬁnished wall.

Remove and discard the plaster guard.

Apply high-quality caulk or sealant around the transfer valve

openings.

Install the transfer valve trim according to the instructions packed

with the trim.

Transfer Valve

Plaster Guard

Apply sealant.

Finished Wall

088037-2-B 8 Kohler Co.

Guide d’installation

Valve transfert à montage mural

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Ne pas retirer les renforts de plâtre de la valve transfert avant

l’instruction de le faire.

Pour un bon ajustement de la garniture, le mur ﬁni doit être

aligné dans une profondeur de [11/16″(1,7 cm)] d’avant en

arrière par rapport au renfort de plâtre installé.

Profondeur de raccordement minimale = [3″(7,6 cm)]; maximale

= [3-7/8″(9,8 cm)].

Une alimentation mélangée d’eau est nécessaire pour ce robinet

coupleur.

Clé à

molette Crayon à papier

Mètre

ruban Tournevis

cruciforme

Kohler Co. Français-1 088037-2-B

Avant de commencer (cont.)

Ne raccorder aucune sortie sur cette valve transfert. La valve

transfert n’est pas conçue pour être utilisé en tant que valve

d’arrêt.

Si moins de trois accessoires seront installés, raccorder le port non

utilisé de la valve transfert à l’un des accessoires. Tous les ports

de sortie doivent être connectés à un accessoire, même si un

accessoire est raccordé à deux ports de sortie de la valve transfert.

Si cette valve transfert est installée au port de la douche du

mitigeur, sa performance en sera réduite.

Ne pas utiliser un tuyau en plastique pour des connexions de

valve transfert.

Planiﬁer soigneusement l’installation avant de commencer.

Veuillez lire avec attention les instructions dans leur intégralité.

L’emplacement des composants, l’espacement et les exigences

relatives à la localisation peuvent varier.

Couper l’alimentation d’eau principale.

Inspecter l’état des tubes d’évacuation et d’alimentation et

remplacer si nécessaire.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations sur

le design des produits et ceci sans préavis, tel que spéciﬁé dans le

catalogue des prix.

088037-2-B Français-2 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Steuereinheit Handbücher

Kohler

Kohler TAUT 73193T-4CD Bedienungsanleitung

Kohler

Kohler 28138T Bedienungsanleitung

Kohler

Kohler K-10675 Betriebsanleitung

Kohler

Kohler TOUCHLESS K-13686 Bedienungsanleitung

Kohler

Kohler K-10959 Bedienungsanleitung

Kohler

Kohler K-10949 Bedienungsanleitung

Kohler

Kohler K-13516X Montageanleitung

Kohler

Kohler K-10675 Bedienungsanleitung

Kohler

Kohler K-2975 Bedienungsanleitung

Kohler

Kohler 5-10EKD Bedienungsanleitung

Kohler

Kohler K-682 Bedienungsanleitung

Kohler

Kohler K-76746GL-NA Bedienungsanleitung

Kohler

Kohler K-402 Montageanleitung

Kohler

Kohler K-528-K1 Montageanleitung

Kohler

Kohler 1216612 Bedienungsanleitung

Kohler

Kohler DTV+ Konnect K-97999-NA Bedienungsanleitung

Kohler

Kohler K301 Bedienungsanleitung

Kohler

Kohler K-400 Bedienungsanleitung

Kohler

Kohler 28139T-DR Bedienungsanleitung

Kohler

Kohler K-8548 Bedienungsanleitung

Kohler

Kohler K-2977 Montageanleitung

Kohler

Kohler K-682 Bedienungsanleitung

Kohler

Kohler Mira Select B14C Bedienungsanleitung

Kohler

Kohler K-305 Montageanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung