Kohler 7000 Series Referenzhandbuch

Service

Manager

Initial Here

Sales

Manager Parts

Manager Chief

Mechanic Mechanic

No. 1 Mechanic

No. 2

Mechanic

No. 3 Mechanic

No. 4

Return

This To

Routing

6/16

348

5/16

DATE REVISEDDATE ISSUED

MODEL

NO.

Service

Bulletin KT715-KT745

Engine Stall

The potential exists for these engines to stall for no apparent reason. This issue is limited to KOHLER®

7000 Series engines within the serial number range of 45327xxxxx through 4613302464. Not all engines in

this serial range will exhibit the condition.

If a customer experiences a stall condition, check the standard items such as proper fuel level, inspect for

fuel cap vent operation, as well as proper fuel ow to the carburetor. If all of these items are found to be

correct and the stall condition still occurs, it is recommended to perform the following x that involves

cuing the existing evap line as shown in Figure 1, inserting a new T-Fiing (25 155 56-S) and a new line

(25 326 28-S 14" cut to an 8" length) that will connect to ing on air cleaner base.

Figure 2. New T-Fitting and New Line Assembly.

4. New T-Fiing and line assembly is shown

installed on the engine in Figure 3.

Cut Existing Evap Line in Half

Figure 1. Cut Existing Evap Line in Half.

3. Install the new T-Fiing at the location of the

cut line. Take the new 25 326 28-S 14" long line

and cut it to an 8" length. Install and route the

new 8" long line as shown in Figure 2.

NOTE: Refer to the appropriate service manual

disassembly and reassembly procedures as

needed.

1. To access the evap line, remove the air cleaner

cover, air cleaner element, and air cleaner

base.

2. Locate the existing evap line (as shown in

Figure 1), remove it from the purge port

nipple on the carburetor, and cut it in half.

Figure 3. New T-Fitting/Line Assembly Installed.

New 8" Long

Line Connects

to Evaporative

Nipple on Air

Cleaner Base

New T-Fitting

Connects to

Purge Port

Nipple on

Carburetor

Connects to OEM Evap/Tank

5. Route the new 8" long evap line from the

T-Fiing to the plugged port on the air

cleaner base. Remove and discard the plastic

cap at that location. See Figure 4.

Figure 4. Connect New 8" Long Evap Line to

Air Cleaner Base.

6. Reassemble the engine following service

manual reassembly procedures as

needed. Run the engine to conrm engine

performance.

Normal warranty terms apply. Submit warranty

claim using 25 326 71-S as the Defective Part

Number and ZZ (Other) as the Failure Code.

Labor Time of up to 0.5 hour using Labor Code

9999 for Misc Labor.

Remove Plastic Cap

and Connect New 8"

Long Evap Line

Breather Hose

Location

Andere Handbücher für 7000 Series

Inhaltsverzeichnis

Andere Kohler Motor Handbücher

Kohler

Kohler Command PRO EFI PCV850 Bedienungsanleitung

Kohler

Kohler Courage XT6.5 Bedienungsanleitung

Kohler

Kohler LOMBARDINI MARINE LMG 4000 Bedienungsanleitung

Kohler

Kohler LOMBARDINI MARINE KDI 1903M-MP Bedienungsanleitung

Kohler

Kohler Command PRO EFI ECV940 Bedienungsanleitung

Kohler

Kohler Courage XT-6 Bedienungsanleitung

Kohler

Kohler K482 Bedienungsanleitung

Kohler

Kohler Lombardini 6 LD 260 Stücklistenhandbuch

Kohler

Kohler KDI 3404TCR-SCR Bedienungsanleitung

Kohler

Kohler CS10 Bedienungsanleitung

Kohler

Kohler Lombardini LGW 523 MPI Benutzerhandbuch

Kohler

Kohler Command PRO CH18 Bedienungsanleitung

Kohler

Kohler M18 Bedienungsanleitung

Kohler

Kohler K91T Bedienungsanleitung

Kohler

Kohler Command PRO CH940 Bedienungsanleitung

Kohler

Kohler KS530 Bedienungsanleitung

Kohler

Kohler KD225 Bedienungsanleitung

Kohler

Kohler Command 6 HP Bedienungsanleitung

Kohler

Kohler K91 Bedienungsanleitung

Kohler

Kohler KDI 3404 TCR Kurzanleitung zur Einrichtung

Kohler

Kohler Courage XT-6 Bedienungsanleitung

Kohler

Kohler KD15 500 Benutzerhandbuch

Kohler

Kohler Courage XT-6 Bedienungsanleitung

Kohler

Kohler LH630-775 Bedienungsanleitung

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung

Bosch

Bosch Rexroth 70 Series Bedienungsanleitung

Wacker Neuson

Wacker Neuson WM 130 Betriebsanleitung