Kohler K-7437 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucets

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-7437 K-7443

1006847-2-C

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Plumbers

Putty Thread

Sealant

Pipe

Sealant

1006847-2-C 2 Kohler Co.

1. Spout Installation

NOTE: For installation of a non-swiveling spout to a thin-walled

lavatory such as stainless steel, remove the nut from the top of the

spout shank.

Locate the center hole and insert the spout.

Slide the metal washer and nut onto the spout shank.

Position the metal washer so the second hole lines up with the

drain lift rod hole on the back of the spout.

Securely tighten the nut with a wrench. Do not overtighten.

Washer

Nut

Spout Shank

Kohler Co. 3 1006847-2-C

2. Handle Valve Installation

NOTE: The valve body marked ″Cold″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Insert the valve bodies into the proper mounting holes.

Rotate each valve body until the copper tubing faces toward the

outside of the lavatory.

Install a washer and a nut onto the underside of each valve body.

While holding the valve bodies in place, securely tighten the nuts

with a wrench. Do not overtighten.

Nut

Washer

Valve Body

1006847-2-C 4 Kohler Co.

3. Supply Tee and Hose Installation

Insert the plastic gasket and the rubber washer into the supply

tee.

Thread the supply tee onto the spout shank until hand-tight.

Ensure that the arms of the supply tee are aligned to face the left

and right sides of the lavatory.

Thread a ﬂexible hose onto each handle valve outlet. Securely

tighten the hose with a wrench. Do not overtighten.

Connect the ﬂexible hoses to the supply tee. Do not use thread

sealant. To avoid kinking the hoses, loop them.

Securely tighten the hose with a wrench. Do not overtighten.

Hose

O-Ring

End Body Outlet

End Body

Supply Tee

Flexible Hose

Gasket

Rubber Washer

Kohler Co. 5 1006847-2-C

4. Drain Style

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

1006847-2-C 6 Kohler Co.

5. Drain Installation - Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply plumbers

putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

Kohler Co. 7 1006847-2-C

6. Complete Drain Installation - Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Body Nut

Stopper

Body

Tailpiece

Seal

Seal Hole

Rod

Apply 3 layers of

sealant tape and a

small bead of pipe

sealant to threads.

Stopper

Nut

Faucet

Rod

Clip

Thumb

Screw

Link

1006847-2-C 8 Kohler Co.

7. Drain Installation - Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Flat Washer

Nut

Drain Body

Fixture

Kohler Co. 9 1006847-2-C

8. Complete Drain Installation - Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, then thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Clip

Stopper

Stopper Nut

Flange

Seal

Rod Nut

Tailpiece

Apply

thread

sealant.

Thumb

Screw

Stopper

Rod

Link

Rod

Lift

Rod

1006847-2-C 10 Kohler Co.

Andere Handbücher für K-7437

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Candide 7688K-4E3 Bedienungsanleitung

Kohler

Kohler Triton K-T7019 Bedienungsanleitung

Kohler

Kohler AMARETTO K-4864T-1/4 Bedienungsanleitung

Kohler

Kohler K-146 Montageanleitung

Kohler

Kohler ODEON 98963M-4 Bedienungsanleitung

Kohler

Kohler K-R399 Montageanleitung

Kohler

Kohler Mira Atom ERD Bedienungsanleitung

Kohler

Kohler ALTERNA Bedienungsanleitung

Kohler

Kohler Cantata K-2199 Bedienungsanleitung

Kohler

Kohler K-3820 Montageanleitung

Kohler

Kohler Archer K-2359X Montageanleitung

Kohler

Kohler K-7213 Montageanleitung

Kohler

Kohler K-2209 Bedienungsanleitung

Kohler

Kohler 9132-2BZ Montageanleitung

Kohler

Kohler Levity K-706013-L Bedienungsanleitung

Kohler

Kohler 13900T-4 Bedienungsanleitung

Kohler

Kohler K-45764X Montageanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-169 Bedienungsanleitung

Kohler

Kohler C3-455 Quiet-Close K-8298-CR Bedienungsanleitung

Kohler

Kohler Stargaze BubbleMassage K-1959-GHW Bedienungsanleitung

Kohler

Kohler ENGLEFIED K-11702X Montageanleitung

Kohler

Kohler K-7853 Bedienungsanleitung

Kohler

Kohler K-19321T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung