Kohler K-3434-X Bedienungsanleitung

Installation Guide

One-Piece Toilet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-3434-X K-3435-X

1023905-2-A

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of personal injury or product damage. Handle

with care. Vitreous china can break or chip if the product is

handled carelessly.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for damage.

If the existing toilet does not have a supply shut-off valve below

the tank, install one before installing the new toilet.

10" Adjustable

Wrench Supply

Shut-Off

Valve

Tape

Measure

Tubing Cutter Safety

Glasses

Plus:

5/16" T-Bolts w/ Nuts and Washers

Putty Knife

Screwdriver

Electrical Tools and Supplies

Metal File

Level

Sponge

Hacksaw

D-Size Batteries

Wax Seal

1023905-2-A 2 Kohler Co.

1. Remove the Existing Toilet

Turn off the water supply.

Flush the toilet, then sponge out all remaining water from the

tank.

Disconnect the supply shut-off valve (if present), and remove the

old tank and bowl.

Remove the old wax seal from the ﬂoor with a putty knife.

Replace the old T-bolts with the new 5/16″diameter T-bolts.

CAUTION: Risk of hazardous gases. If the new toilet is not

installed immediately, temporarily stuff a rag in the closet ﬂange.

T-Bolt

Scrape off the old

wax seal

Closet

Flange

Kohler Co. 3 1023905-2-A

2. Install the New Toilet

Install or relocate the supply and outlet as necessary to conform

to the roughing-in dimensions.

Install a supply shut-off valve.

Record the model number in the Homeowners Guide.

Lay the toilet down onto a padded surface.

From the bottom of the toilet, ﬁrmly press a new wax seal around

the toilet outlet.

Remove the temporary rag (if used) from the toilet ﬂange hole.

Align and lower the toilet over the ﬂange and T-bolts.

CAUTION: Risk of external leakage. Do not lift or rock the

bowl after placement. If you break the watertight seal, you must

install a new wax seal.

Apply your full body weight around the toilet to set the seal.

Place the plastic bolt cap bases over the T-bolts in the ″up″

position as marked.

Place the metal washers and nuts on the plastic bolt cap bases

and T-bolts.

CAUTION: Risk of product damage. Overtightening may cause

breakage or chipping of vitreous china.

Bottom of Bowl

Wax Seal Bolt Cap

Nut

Washer

Bolt Cap Base

T-Bolt

T-Bolt Closet Flange

1023905-2-A 4 Kohler Co.

Install the New Toilet (cont.)

Carefully tighten the nuts.

NOTE: To achieve optimum performance, be sure the bowl is level.

CAUTION: Risk of product damage. Protect the vitreous china

from exposure to the saw blade when cutting off excess T-bolt

length.

If the T-bolts extend more than 1/4″(6mm) over the top of the

nuts, cut off the excess.

Attach the bolt caps.

Kohler Co. 5 1023905-2-A

3. Activation Sensor and Chain Assembly

NOTE: The activation sensor must be installed exactly as shown.

Position the activation sensor.

Cut and remove the wire tie.

Position the sensor wire on the center of the toilet tank front rim.

Place the end of the activation sensor 1-5/16” (3.3cm) to the right

of the toilet centerline.

NOTE: It is not necessary to rotate the activation sensor while it is

cradled in the wire basket.

NOTE: The sensor activates the toilet ﬂushing mechanism when the

magnet in the seat is brought within 3” (7.6cm) of the sensor for at

least 20 seconds.

Route the sensor wire to the left, near the ﬂoat valve, as shown.

This ensures that polarity exists between the sensor and the

magnet in the seat.

NOTE: Make sure the sensor wire does not interfere with the

operation of the ﬂoat valve.

Place the mounting bracket for the housing assembly on the back

of the toilet tank in an area extending 3-1/8″(7.9cm) to the right

of the toilet centerline.

Latch Hinges

Housing

Assembly

3-1/8"

(7.9cm)

1-5/16"

(3.3cm)

Mounting

Bracket

Activation

Sensor

Centerline

of Toilet Toilet Housing

Assembly

Chain

Assembly

S-Hook

Flapper

Cam

Flush

Valve

Assembly

1023905-2-A 6 Kohler Co.

Activation Sensor and Chain Assembly (cont.)

Install or Replace the Batteries

Insert a screwdriver blade into the seam on top of the housing

assembly.

Carefully pry open the battery compartment latch and disengage

the other side of the latch from the hinges.

Install two D-size batteries into the compartment.

Snap the latch back into place.

Adjust the Chain Assembly

Move the S-hook up or down on the chain link as needed to

achieve the desired chain slack. For a proper ﬂush, ensure that

enough chain slack remains for the cam to rotate and open the

ﬂapper completely.

Make additional adjustments by loosening the screws on the back

of the mounting bracket. Raise or lower the mounting bracket to

adjust the chain slack.

If you adjust the mounting bracket, make sure adequate clearance

exists between the housing assembly, ﬂush valve, tank walls, and

tank cover.

Kohler Co. 7 1023905-2-A

4. Complete the Installation

Connect the supply shut-off valve to the toilet supply shank.

Open the supply shut-off valve slowly to check for leaks. If the

connections have been properly assembled, a slight tightening of

the nuts should stop any leakage.

NOTE: Do not substitute another seat. The seat included contains

elements of the Peacekeeper ﬂush system.

Install the toilet seat according to the packed instructions.

Carefully set the cover onto the tank.

Flush the toilet several times and check all connections for leaks.

Periodically check for leaks for several days following the

installation.

Tubing

Ferrule

Supply Shank

Seal Washer Comp. Washer

Tubing

Ferrule

Fill Valve Nut

Supply Shut-Off Valve Connection

Coupling

Nut

Comp. Nut

Supply Shut-Off

Valve

Comp. Nut

Coupling

Nut

1023905-2-A 8 Kohler Co.

Guide d’Installation

Mono W.C.

Outils et Matériaux

Merci d’avoir choisi un produit KOHLER

Nous apprécions votre engagement envers la qualité KOHLER. S’il

vous plait, prenez quelques minutes et lisez attentivement ce guide

avant de commencer votre installation. N’hésitez pas à nous contacter

en cas de problème d’installation ou de fonctionnement. Nos numéros

de téléphone et notre adresse du site Internet sont au verso. Merci

encore d’avoir choisi un produit KOHLER.

Avant De Commencer

ATTENTION : Risque de blessures ou d’endommagement du

produit. Manipulez avec précaution. La Porcelaine de Chine peut

se casser ou se fendre si le produit est manipulé avec négligence.

Respectez tous les codes locaux de plomberie et de bâtiment.

Examinez soigneusement le nouveau W.C. pour déceler tout

dommage.

Si le W.C. existant ne comporte pas de robinet d’arrêt sur l’arrivée

d’eau située sous le réservoir, installez en un avant d’installer le

nouveau W.C.

Kohler Co. Français-1 1023905-2-A

1. Retirez le W.C.

Fermez l’arrivée d’eau.

Activez la chasse d’eau du W.C. et épongez le restant d’eau du

réservoir.

Débranchez le robinet d’arrêt (le cas échéant) et retirez le

réservoir et la cuvette.

Délogez du sol l’anneau en cire existant avec un couteau à mastic.

Remplacez le vielle écrou en T avec un neuf de Ø 5/16″.

ATTENTION : Risque de fuites de gaz nocives. Si l’installation

du nouveau W.C. doit être retardée, recouvrir temporairement la

bride du sol avec un chiffon.

1023905-2-A Français-2 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler SAN RAPHAEL GRANDE K-8688T-HC Bedienungsanleitung

Kohler

Kohler K-5401 Bedienungsanleitung

Kohler

Kohler Reve Comfort Height K-3797-0 Montageanleitung

Kohler

Kohler Revival K-14224-TL Montageanleitung

Kohler

Kohler K-6299 Benutzerhandbuch

Kohler

Kohler WELLWORTH K-3432 Bedienungsanleitung

Kohler

Kohler 1278653-2-C Bedienungsanleitung

Kohler

Kohler VIA K-20629T-BW Bedienungsanleitung

Kohler

Kohler EIR Montageanleitung

Kohler

Kohler PATIO URINAL Bedienungsanleitung

Kohler

Kohler K-3723 Montageanleitung

Kohler

Kohler K-5889X Montageanleitung

Kohler

Kohler K-3615 Montageanleitung

Kohler

Kohler K-8688X Montageanleitung

Kohler

Kohler WELLWORTH LITE K-4229 Bedienungsanleitung

Kohler

Kohler K-30311X Montageanleitung

Kohler

Kohler K4915 Bedienungsanleitung

Kohler

Kohler VEIL K-5402A-0 Bedienungsanleitung

Kohler

Kohler K-22106T-2 Bedienungsanleitung

Kohler

Kohler C3-230 Montageanleitung

Kohler

Kohler K-19796 Bedienungsanleitung

Kohler

Kohler ESCALE K-32771T-NS Bedienungsanleitung

Kohler

Kohler K-5401TW-2-0 Montageanleitung

Kohler

Kohler ESCALE K-24837T-S Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung