Kohler K-200 Montageanleitung

Installation and Care Guide

Water Filtration System

K-200, K-201, K-202

Français, page “Français-1”

Español, página “Español-1”

1270310-2-A

Important Safety Instructions

READ AND FOLLOW ALL

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: Risk of personal injury or property damage.

Please read all instructions thoroughly before beginning

installation, including the following requirements.

WARNING: Risk of personal injury. To reduce the risk of

choking, do not allow children to access small parts during

the installation.

WARNING: Risk of personal injury. To reduce the risk of

ingesting contaminants, do not use with water that is

microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system. Systems

certiﬁed for cyst reduction may be used on disinfected water

that may contain ﬁlterable cysts. EPA Establishment No.

10350-MN-007.

CAUTION: Risk of personal injury. Kohler K-200/K-201 is

intended for use in ﬁltering potable water and has not been

evaluated for other uses. The product is installed at the point

of use and must be installed as speciﬁed in the installation

instruction by a qualiﬁed professional.

CAUTION: Risk of property damage. To protect from

freezing, remove the ﬁlter cartridge when temperatures may

drop below 33°F (4.4°C).

CAUTION: Risk of property damage. The maximum water

temperature of this ﬁlter system is 100°F (37.8°C). Do not

install on hot water supply lines or in an area where the

ambient temperature may exceed 110°F (43.3°C).

CAUTION: Risk of personal injury or property damage.

Use caution when installing near water pipes or electrical

lines.

1270310-2-A 2 Kohler Co.

Important Safety Instructions (cont.)

Do not install this system if your water pressure exceeds 125 psi

(862 kPa). For water pressure between 80 psi (552 kPa) and 125

psi (862 kPa), you must install a pressure reducing valve to

regulate the pressure to <80 psi (552 kPa).

The ﬁlter cartridge must be replaced every 6 months or sooner.

Failure to replace the cartridge at the recommended intervals may

lead to reduced ﬁlter performance and failure of the ﬁlter.

If a booster pump is installed on your water system, you must

install an appropriate pressure relief valve. Inspect and maintain

the booster pump and attached pressure switch, and the pressure

relief valve, every 6 months or according to the manufacturer’s

instructions.

If you are uncertain how to install and maintain any required

components for this system, contact a plumbing professional.

Tools and Materials

Before You Begin

CAUTION: Risk of personal injury. Kohler K-200/K-201 is

intended for use in ﬁltering potable water and has not been

evaluated for other uses. The product is installed at the point

of use and must be installed as speciﬁed in the installation

instruction by a qualiﬁed professional.

Observe all local plumbing and building codes.

Inspect the plumbing and supplies for damage. Replace or repair

as needed.

Plus:

• Adapter

• Thread Sealant Tape

Adjustable

Wrench

Phillips

Screwdriver

Kohler Co. 3 1270310-2-A

Before You Begin (cont.)

Install the water ﬁltration system to a cold water supply only. Do

not install the system to a hot water supply.

Do not install where water hammer conditions may occur. If

water hammer conditions exist you must install a water hammer

arrester.

Where a backﬂow prevention device is installed on a water

system, a device for controlling pressure due to thermal

expansion must be installed.

If needed, clean the exterior of the unit with mild soap and water.

Do not use chemical cleaners.

The water ﬁltration system must be mounted vertically.

If a faucet other than a KOHLER beverage faucet will be installed

with the water ﬁltration system, you will need to purchase an

adapter to connect the outlet of the ﬁlter to the faucet inlet.

Do not use this water ﬁlter system with a standard faucet that

uses hot and cold inlets. A single inlet faucet, such as a KOHLER

beverage faucet, must be used.

The water ﬁltration system is designed to be installed under a

sink. Make sure that the bottom of the ﬁlter cartridge is at least 2″

(51 mm) from the ﬂoor of the cabinet.

Do not connect the water ﬁltration system to a dishwasher.

Filter cartridges should be replaced when the capacity has been

exceeded, or when a noticeable decrease in ﬂow is observed.

To ensure that this equipment is functioning properly and

effectively, replace the ﬁltration system after 10 years.

Replacement date:___________

Keep this installation guide for future use.

1270310-2-A 4 Kohler Co.

Cartridge Replacement Information

The K-200 water ﬁltration system comes complete with the K-201 Hi

Flow ﬁlter cartridge. Optional K-202 replacement cartridges are

available separately.

Service parts and replacement cartridges are available from your

local distributor or directly from Kohler Co.:

Kohler Co., 444 Highland Drive, Kohler, Wisconsin, 53044

Application Guideline/Water Supply Parameters

Capacity: 1,500 gal (5,678 L)

Water Pressure: 30 (206 kPa) - 125 psi (862 kPa)

Water Temperature: 40°F (4.4°C) - 100°F (38°C)

Flow Rate (K-200/K-201): 1.5 gal/min (5.68 l/min)

Flow Rate (K-202): 0.6 gal/min (2.27 l/min)

Replacement

Element

Tested and Certified by NSF International against

NSF/ANSI Standard 42 for the reduction of the

Nominal Particulate (Class I), Chlorine Taste and

Odor, and against NSF/ANSI Standard 53 for the

reduction of Cysts and Turbidity in Model

K-200/K-201, K-6665-F/K-201 and K-6666-F/K-201.

Tested and Certified by NSF International against

NSF/ANSI Standard 42 for the reduction of

Nominal Particulate (Class I), Chlorine Taste and

Odor and against NSF/ANSI Standard 53 for the

reduction of Cysts and Lead in Model

K-200/K-202, K-6665-F/K-202 and K-6666-F/K-202.

K-202 Premium Filter Cartridge

K-201 Hi Flow Filter Cartridge

Replacement

Element

Kohler Co. 5 1270310-2-A

1. Assemble the Filtration System

Write the system replacement date on the ﬁlter head label. This is

the installation date plus 10 years.

Place the mounting bracket over the port marked ″OUTLET″on

the ﬁlter head.

Attach the mounting bracket to the ﬁlter head using the screws

provided. Do not overtighten.

Apply four layers (four turns) of thread sealant tape to the

threads of each nipple.

Thread each nipple into the inlet and outlet port of the ﬁlter head

until ﬁnger tight plus one turn maximum. Do not overtighten the

nipple hex. The nipple hex should not make contact with the

ﬁlter head.

Inlet

Outlet

Mounting

Bracket

Nipples

Hex

Apply thread

sealant tape.

Label

1270310-2-A 6 Kohler Co.

2. Mount the Filtration System

CAUTION: Risk of property damage. Do not install the unit

where the temperature may drop below freezing, may be

exposed to direct sunlight, or may be exposed to heat.

CAUTION: Risk of personal injury or property damage.

Use caution when installing near water pipes or electrical

lines.

IMPORTANT! The unit must be mounted vertically.

IMPORTANT! The mounting location of the water ﬁltration system

is critical. Verify the following before mounting: the bottom of the

ﬁlter cartridge will be at least 2″(51 mm) from the ﬂoor of the

cabinet, the system will not interfere with other items under the

counter, and the hoses will not be under tension when installed to

the ports on the ﬁlter head.

Align the mounting holes of the mounting bracket at the

determined location.

Mark the mounting hole locations with a pencil. Set the unit

aside.

Pre-drill the holes, if necessary.

Partially thread the screws into the cabinet wall and slide the

mounting bracket over the screws.

Secure the screws into the cabinet wall.

Screws

(Not Supplied)

Mounting

Bracket

Kohler Co. 7 1270310-2-A

3. Install or Replace the Cartridge

Write the installation date on the new ﬁlter cartridge label.

Remove and discard the cap from the cartridge.

Inspect the cartridge for damage.

Verify both O-rings are present and positioned correctly in the

grooves.

Moisten the O-rings with water. Do not use petroleum products

to lubricate the O-rings.

Align the groove in the top of the cartridge with the word ″OFF″

on the ﬁlter head.

Insert the top of the cartridge into the ﬁlter head and turn the

cartridge counterclockwise 90° until handtightened.

For cartridge replacement:

Run the faucet for at least 2 minutes to remove any air in the

system. Any air left in the system may temporarily cause the

water to be cloudy.

Check all connections for leaks.

Groove

Cartridge

Filter Head

Write the date

on the label.

O-Rings

Cap

1270310-2-A 8 Kohler Co.

4. Connect the Supply

NOTE: The hoses must be connected as directed. Do not reverse the

connections.

NOTE: Do not use this water ﬁltration system with a standard

faucet that uses hot and cold inlets. A single inlet faucet must be

used.

NOTE: The provided hoses will connect directly to a 3/8″male

compression ﬁtting.

NOTE: If you are installing a KOHLER beverage faucet, use the

adapter provided with the water ﬁltration system. If you are

installing this system to any other single inlet faucet, you will need

to purchase an adapter to ﬁt the faucet inlet.

Connect the outlet hose from the outlet port on the ﬁlter head to

the adapter on the faucet inlet.

Connect the inlet hose from the inlet port on the ﬁlter head to the

cold water supply.

Outlet Hose

Faucet Inlet

Cold Water

Supply

Inlet Hose

Adapter

Kohler Co. 9 1270310-2-A

5. Complete the Installation

Turn on the water supply and check all connections for leaks.

Repair as needed.

Run water through the faucet for at least 2 minutes to remove

any air in the system. Any air left in the system may temporarily

cause the water to be cloudy.

Warranty

KOHLER

Water Filter Systems

FIVE-YEAR LIMITED WARRANTY

KOHLER K-200 water ﬁlter systems (excluding the K-201, K-202, and

K-203 disposable replacement cartridges) used in the United States and

Canada are warranted to be free of defects in material and

workmanship for ﬁve (5) years from the date of purchase in normal

residential use. (The service life of any disposable replacement

cartridge varies with local water conditions and water consumption

and thus is not warranted other than to be free of defects in material

and workmanship at the time of purchase.)

All products must be installed and operated in accordance with the

manufacturer’s recommended procedures and guidelines. Improper use

or installation could void this warranty.

If a defect is found in normal residential usage in the United States or

Canada, Kohler Co. will, at its election, repair or replace the unit, or

make appropriate adjustment. Damage caused by accident, misuse, or

abuse is not covered by this warranty. Kohler Co. is not responsible for

1270310-2-A 10 Kohler Co.

Andere Handbücher für K-200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Wasserfiltersystem Handbücher

Kohler

Kohler K-77686-NA Montageanleitung

Kohler

Kohler K-78433T-KH200-AF Bedienungsanleitung

Kohler

Kohler Aquifer K-22155-NA Bedienungsanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-80021T-KPC40-01R Bedienungsanleitung

Kohler

Kohler Toobi K-96024T-PF100-Q73 Bedienungsanleitung

Kohler

Kohler K-80021T-KP060-01R Bedienungsanleitung

Kohler

Kohler TOOBI 5020 Bedienungsanleitung

Kohler

Kohler Aquifer Refine K-21371 Montageanleitung

Kohler

Kohler K-24210T-KT300-01R Bedienungsanleitung

Kohler

Kohler K-5339T-KT100 Bedienungsanleitung

Kohler

Kohler KT001-MF Bedienungsanleitung

Kohler

Kohler Carafe Series Bedienungsanleitung

Kohler

Kohler CLARITY Bedienungsanleitung

Kohler

Kohler LISON 21729T-PP020-01R Bedienungsanleitung

Kohler

Kohler K-200 Bedienungsanleitung

Kohler

Kohler Bevel Series Bedienungsanleitung

Kohler

Kohler K-8802 Bedienungsanleitung

Kohler

Kohler K-6665 Bedienungsanleitung

Kohler

Kohler CLARITY Bedienungsanleitung

Kohler

Kohler K-32435T-KP040-01R Bedienungsanleitung

Kohler

Kohler REVE Series Bedienungsanleitung

Kohler

Kohler Aquifer 22156-NA Bedienungsanleitung

Kohler

Kohler 21372-NA Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung