Kohzu Precision KOSMOS series Bedienungsanleitung
User's Manual
Read this manual before using this product.
Keep in a convenient place for future reference.
Multi-Axis Controller
KOSMOS series
Model: ARIES/LYNX
operation
manual
Rev1.42
Kohzu Precision Co., Ltd.
1
Symbols Identifications
In this document, noted items that should be followed to prevent danger to people
and damage to the device are divided as shown next.
Prohibited
This symbol indicates prohibited items. Do not conduct actions specified under
this symbol.
Warning（Caution）
This symbol indicates items that require warning (caution). If operation is
conducted ignoring noted contents, it may cause injury or physical damage.
Note/Remarks
This symbol indicates items to provide further understanding or useful
information.
！
In this document, information and operation method for the multi-axis controller
"ARIES" and "LYNX" are explained.
Please read and understand this document thoroughly to utilize the functions of
"ARIES" and "LYNX" in the best condition.
In addition, keep this document in a convenience place for future reference.
Introduction
2
Safety Precautions
Do not apply severe shock to the product and
avoid using in a place with vibration.
Liquid or chemical splashes on this device
are dangerous and cause failures.
Never use this device in the place above
phenomena may occur.
Use 90-240V AC (50/60Hz) as a power supply.
*Confirm ratings of the power cable.
*Always ground FG (frame ground).
This product is precision electronic
equipment. Because malfunction may occur
near large motors, high voltage electric
devices or device that generates strong
magnetism, do not use this product under
these environment.
Do not disassemble or modify the product.
Pay close attention when connecting the
motor driven stage or a motor other than
those specified by our company.
When the controller's power supply is turned
ON, do not pull out or insert cables.
KOSM OS
KOSMOS
×
×
KOSMOS
KOSM O S
AC90V～AC240V
×
KOSM O S
KOSMOS
？
KOSMO S
×
KOSMOS
×
S
N
！
！
！
3
Table of Contents
Introduction ................................................... 1
Symbols Identifications ................................. 1
Safety Precautions ....................................... 2
Table of Contents ......................................... 3
1. Product Summary .................................. 5
1-1. About this Product .............................. 5
1-1-1. Features of this Product ................. 5
1-1-2. Product Configuration Example ...... 6
1-2. List of Functions ................................. 7
1-3. Attachments and Options .................. 8
1-3-1. Attachments ................................... 8
1-3-2. Optional Products (required) .......... 9
1-3-3. Optional products
(convenient tools) ...........................10
2. Installation and Preparation ................ 11
2-1. Proceeding with Installation and
Preparation ....................................... 11
2-2-1. Part Names ................................... 12
2-2-1. Part Names of ARIES ................... 12
2-2-2. Part Names of LYNX .................... 13
2-3. Connection method .......................... 14
2-4. Rotary Switch for Communication
Setting ............................................... 15
2-5. Device No. Setting Switch ................ 16
3. Functions ............................................... 17
3-1. Speed Setting ................................... 17
3-1-1. Speed Table ................................. 17
3-1-2. Speed Change in Remote Control...
17
3-1-3. Speed Setting Regulations ........... 18
3-2. Acceleration Pattern ........................ 19
3-3. Backlash Correction ........................ 20
3-3-1. Setting Steps ................................ 20
3-3-2. Details of Correction Method ........ 21
3-4. Trigger Specification ........................ 22
3-4-1. Trigger Signal Output Method ...... 22
3-4-2. Trigger Signal Setting Procedures ...
22
3-4-3. Explanation of Trigger Function .... 23
3-5. Emergency Stop Function ............... 26
3-6. Stepping Motor Excitation and Servo
ON/OFF Specification ...................... 27
3-7. Soft Limit Setting .............................. 27
3-8. Encoder Correction .......................... 28
3-8-1. Encoder Correction ....................... 28
3-8-2. Encoder Feedback Setting ........... 29
3-9. Origin Return Method ...................... 30
3-10. ARIES Touch Panel "PYXIS" ........ 40
3-10-1. Connection and Operation ......... 40
3-10-2. "Main" Screen Details ................ 41
3-10-3. "ABS" Screen Details ................. 42
3-10-4. "REL" Screen Details ................. 42
3-10-5. "SYS" Screen Details ................. 43
3-10-6. "PYXIS" Display Error List .......... 45
3-11. General I/O .................................... 46
4
4. Remote Control .................................... 47
4-1. Proceeding with Installation and
Preparation ....................................... 47
4-1-1. Transmitting/Receiving ................. 47
4-1-2. Remote Control Procedures ......... 48
4-1-3. Command Format ........................ 48
4-1-4. Response ..................................... 49
4-1-5. Characters to Use ........................ 50
4-2. Ethernet (TCP/IP) Communication ... 51
4-2-1. Flow from Ethernet (TCP/IP) Related
Parameter Setting to Connection ... 52
4-2-2. Cautions when Multiple Clients are
Connected ..................................... 55
4-2-3. Other Cautions ............................. 55
4-3. Command List ................................. 56
4-4. Command Details ............................ 58
4-5. Error Code ...................................... 110
4-5-1. Error Code and Warning
Code List ...................................... 111
4-6. System Settings ............................. 113
4-6-1. System Setting List ..................... 113
4-6-2. System Setting Details ................ 115
5. Specification ........................................ 122
5-1. Specification ................................... 122
5-2. Connector ....................................... 123
5-2-1. Motor Connecting Connector ...... 123
5-2-2. Encoder Connector ..................... 124
5-2-3. I/O Connector .............................. 125
5-2-4. Emergency Stop Signal Input
Connector ..................................... 126
5-2-5. Trigger Signal Output Connector .
... 126
5-2-6. RS-232C Connector .................... 127
5-3. Input/Output Signal Circuit
Diagram .......................................... 128
5-4. Appearance Dimensions ................ 129
6. Maintenance and Service ................... 132
6-1. Troubleshooting .............................. 132
6-2. Maintenance ................................... 134
6-3. Warranty and Service ..................... 134
6-4. Contact ............................................134
Ex Revision History ................................... 135
5
1. Product Summary
Thank you for purchasing our multi-axis controller "ARIES" and "LYNX".
Adopting Motionnet®, "ARIES" and "LYNX" are controllers that enable comprehensive
system configuration through unified management of multi-axis control.
By installing more LYNX (slave controller) for ARIES (master controller), 32 axes can be
controlled at maximum.
While keeping the functions of SC series as feedback control and trigger function, new
functions as servo control, general I/O and soft limit are added.
1-1-1. Features of this Product
1-1. About this Product
●Completely supports our company's motor drive precision stage <MontBlanc
Series>.
●In addition to 5-phase micro step motor drive, a connection is possible for 2-phase
motor driver of pulse train control or servo driver connection.
●Supports rectangular drive, trapezoid drive, S shape drive, asymmetric trapezoid
drive and asymmetric S shape drive.
●Origin return method can be selected from 15 kinds (+ORG OFFSET).
●Remote control by Ethernet(TCP/IP) communication is possible.
●Remote control by RS-232C communication is possible.
●Control is possible with "PYXIS" (option), a touch panel for "ARIES".
●Control is possible through application for stage drive, "Chamonix" that comes with
this product.
Please download from our company's HP.
http://www.kohzu.co.jp/
6
1-1-2. Product Configuration Example
■Outside of product range
This product does not offer the following functions.
・Automatic operation is not possible with only ARIES and LYNX.
*For automatic operation, connect a computer with ARIES and conduct with remote control.
*It is possible to operate with Touch Panel PYXIS (sold separately). (Excluding some functions).
・Not compatible with some remote controls (sequencer connection, etc.) besides RS-232C and
Ethernet (TCP/IP) communication.
ARIES/LYNX System Configuration Example
Control application Chamonix
(WINDOWS application)
*Note
・Motionnet cable (1m) is an accessory of
LYNX.
・A control cable and motor cable must be
purchased separately.
Motionnet
cable
ARIES
Cable for
touch panel
Optional touch panel,
PYXIS
Communication
cable RS-232C Installable up to 15 LYNX
Motionnet
cable
Motionnet
cable
Able to control 32 axes at maximum
Stage (1 axis)
Motor
cable
Control
cable
LYNXLYNX
Control
cable
Control
cable
Control
cable
Control
cable
Control
cable
Motor
cable
Motor
cable
Motor
cable
Motor
cable
Motor
cable
Stage (1 axis)
Stage (2 axes) Stage (2 axes)
2 axes driver BOX
5-phase stepping motor driver
2 axes driver BOX
2-phase stepping motor driver
2 axes driver BOX
Servo motor driver
7
1-2. List of Functions
Relative Position
Movement
(4 axes simultaneous
start is possible)
Moves toward the designated direction from the present position by a set
value.
Absolute Position
Drive
(4 axes simultaneous
start is possible)
Moves to the designated target position.
Origin Return
Movement
Performs origin return with the specified origin return method.
2000 1000 0
(Now Position)
First movement
amount
Second movement
amount
CW CCW
Example：
Move to CW angle(1000
pulse)at two times.
Target Position
Start Position①
CW CCW Example：
Start position① or
start position② move
to target position.
Start Position②
Origin
Start Position①
CW CCW Example：
Start position① or ②
move return Origin
position.
Start Position②
8
1-3. Attachments and Options
* The standard Motionnet®cable is a LAN
cable with CAT5e or more shield (straight).
If a longer cable is required than the
attached cable, please purchase separately.
* The maximum length of Motionnet®cable
shall be the Motionnet®cable length with
connected ARIES/LYNX < 100m.
1-3-1. Attachments
The following items come as accessories for the products.
Make sure to check that all items are included.
Immediately contact your retainer or our sales department if there are missing or damaged
parts.
①Power cable (3P)
A power cable (3P) for AC100V comes as standard.
In addition, a 3P->2P conversion plug comes as an option.
*A power cable for AC200V must be prepared by customer or contact our sales department.
②Motionnet®connector/cable
A connector/cable to connect between ARIES-LYNX.
A terminal plug for ARIES and 0.5m Motionnet®cable for LYNX come as accessories.
③Emergency stop short plug
A short plug to connect when not using the
emergency stop signal comes as an
accessory.
9
1-3-2. Optional products (required)
A driver BOX necessary to drive the <MontBlanc series>, a motor cable for KOSMOS series, an
encoder cable, and a RS-232C (cross) communication cable used to control from a computer or a
LAN cable do not come with the product.
Please purchase a driver BOX, a motor cable and an encoder cable separately.
Also, purchase a communication cable or LAN cable (recommended CAT5e or more) available on
the market.
Motor cable list for KOSMOS series
Driver connection cable list for KOSMOS series
*The encoder cable is an ordered product.
Other types of cable (for 10-lead and square connector) can also be manufactured.
For details, please contact our sales department.
Driver BOX list for KOSMOS series
Type Driver BOX type
AC driver BOX for 2 axes TITAN-AⅡ
DC driver BOX for 2 axes TITAN-DⅡF
Length Cable type
0.5m CPS005
1m CPS010
Stage side
Connector shape Fixed cable Moving cable
3m CB1503 RCB1503
5m CB1505 RCB1505
10m CB1510 RCB1510
Length
Round type
connector
Cable type
Andere Handbücher für KOSMOS series
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Kohzu Precision Controller Handbücher
