Kollmorgen SL3000 Bedienungsanleitung

SL3000 QUICK START GUIDE

This guide is for operators who would like to get up and running quickly with a minimal amount of research

through the manual. Section 2 and sections 3.1 through 3.8 of the SL3000 instruction manual must be read.

1. Follow all safety and installation instructions as specified in Section 2, Installation Instructions.

BEFORE APPLYING POWER, VERIFY THAT THE PROPER VOLTAGE IS AVAILABLE

FOR THE INVERTER. FAILURE TO DO THIS CAN RESULT IN EQUIPMENT

DAMAGE AND PERSONAL INJURY.

2. Check all terminal connections for loose connections. Re-verify the proper motor wiring for the

voltage being applied.

3. The only connections needed on the terminal strip for keypad control are TB1-11 (Logic Common)

connected to TB1-12 (External Trip) and TB1-21 (Logic Common) connected to TB1-22 (Stop). TB1-11

and TB1-21 are both common and reference the same point.

4. Apply AC power to the input terminal (L1, L2, L3). The following will appear on the display if there

are no faults. The factory settings are for keypad operation in the forward direction.

SP0: 0 RPM

stopped

5. To change any parameters use the following procedure

a. Press the PROG key.

b. Use the MENU key to reach the desired menu.

c. Use the UP or DOWN arrow keys to get to the parameter to be changed.

d. Press the EDIT key.

e. Press the UP or DOWN arrow keys to change the parameter to a new value.

f. Press EDIT to store the new value.

g. Press the MENU key to get to a new menu.

h. Press the PROG key to exit the programming mode.

6. The standard default parameter settings should be sufficient for most applications. The parameters that

are most often changed are in the first parameter menu, MAIN MENU ( Menu 0 ) and parameter

Pr300, full load motor nameplate current. The drive performance parameters are Pr311, Slip Factor

and Pr312, Boost Factor.

7. Use the RUN FWD key to start the motor and increase the setpoint with the UP arrow keys. When

the motor starts to rotate, note the direction of rotation. If the motor is turning in the wrong direction,

STOP THE DRIVE, REMOVE AC POWER AND WAIT FOR THE BUS CHARGE

INDICATOR TO GO OUT. After the Charge indicator is extinguished, wait two minutes and

reverse any two of the motor leads (T1, T2, T3).

8. Reapply AC input power and confirm motor rotation. Use the UP and DOWN arrow keys to set speed.

9. The inverter is preset to run a “typical” NEMA B induction motor to a maximum speed of 1800 RPM

with both acceleration and deceleration times set to 3.0 seconds

10. Press the STATUS key to view the motor amps, motor frequency, buss voltage, etc..

LIM 55438 REV 0 3/95

Inhaltsverzeichnis

Andere Kollmorgen Servoantrieb Handbücher

Kollmorgen

Kollmorgen AKD PDMM Stücklistenhandbuch

Kollmorgen

Kollmorgen C04 Bedienungsanleitung

Kollmorgen

Kollmorgen AKD Bedienungsanleitung

Kollmorgen

Kollmorgen AKM11B Stücklistenhandbuch

Kollmorgen

Kollmorgen SERVOSTAR 400 Bedienungsanleitung

Kollmorgen

Kollmorgen EB-10X Series Handbuch

Kollmorgen

Kollmorgen P70530 Bedienungsanleitung

Kollmorgen

Kollmorgen AKD PROFINET RT Communication Bedienungsanleitung

Kollmorgen

Kollmorgen AKD Bedienungsanleitung

Kollmorgen

Kollmorgen AKD PDMM series Bedienungsanleitung

Kollmorgen

Kollmorgen AKD series Bedienungsanleitung

Kollmorgen

Kollmorgen AKD-N series Bedienungsanleitung

Kollmorgen

Kollmorgen PC830 Kurzanleitung

Kollmorgen

Kollmorgen SERVOSTAR 300 Bedienungsanleitung

Kollmorgen

Kollmorgen AKD PDMM Bedienungsanleitung

Kollmorgen

Kollmorgen AKD-CC Bedienungsanleitung

Kollmorgen

Kollmorgen S700 Series Installations- und Betriebsanleitung

Kollmorgen

Kollmorgen AKD2G-S Series Bedienungsanleitung

Kollmorgen

Kollmorgen AKD-N00607 Bedienungsanleitung

Kollmorgen

Kollmorgen S70101 Bedienungsanleitung

Kollmorgen

Kollmorgen S20260 Bedienungsanleitung

Kollmorgen

Kollmorgen AKD2G-S Series Bedienungsanleitung

Kollmorgen

Kollmorgen EB-9207 Beilage

Kollmorgen

Kollmorgen AKD EtherCAT Bedienungsanleitung

Beliebte Servoantrieb Handbücher anderer Marken

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Bedienungsanleitung

Robotis

Robotis XH430-W350-T Bedienungsanleitung

NTI AG

NTI AG LinMot C1250 Series Bedienungsanleitung

Welcon

Welcon WE2A D048 Series Bedienungsanleitung

Parallax

Parallax 900-00005 Bedienungsanleitung

Festo

Festo TP 1410 Bedienungsanleitung

Axor

Axor MAGNUM 400 Bedienungsanleitung

Siemens

Siemens SINAMICS S120 Bedienungsanleitung

Danfoss

Danfoss 176F6494 Bedienungsanleitung

THORLABS

THORLABS TDC001 Bedienungsanleitung

TECO

TECO JSDAP Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Bedienungsanleitung

GSK

GSK DA98D Bedienungsanleitung

Lenze

Lenze m850 Leitfaden

Baumuller

Baumuller b maXX 3000 Handbuch

Baumuller

Baumuller b maXX 5000 Handbuch

Baumuller

Baumuller b maXX 5500 Handbuch

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung