Komatsu PC130-7 Handbuch

PC130-7

SERIALNUMBER

PC130-7-72642andup

HYDRAULIC EXCAVATOR

Unsafe use of this machine may cause serious injury or

death. Operators and maintenance personnel must read

this manual before operating or maintaining this

machine. This manual should be kept inside the cab for

reference and periodically reviewed by all personel who

will come into contact with the machine.

Operation &

Maintenance Manual

UEAM003604

WARNING

FOREWORD

FOREWORD FOREWORD

1-2

FOREWORD 1

This manual provides rules and guidelines which will help you use this machine safely and effectively. The pre-

cautions in this manual must be followed at all times when performing operation and maintenance. Most accidents

are caused by the failure to follow fundamental safety rules for the operation and maintenance of machines. Acci-

dents can be prevented by knowing beforehand conditions that may cause a hazard when performing operation

and maintenance.

WARNING

Operators and maintenance personnel must always do as follows before beginning operation or mainte-

nance.

Always be sure to read and understand this manual thoroughly before performing operation and mainte-

nance.

Read the safety messages given in this manual and the safety labels affixed to the machine thoroughly

and be sure that you understand them fully.

Keep this manual at the storage location for the Operation and Maintenance Manual given below, and have

all personnel read it periodically.

If this manual has been lost or has become dirty and cannot be read, request a replacement manual imme-

diately from Komatsu or your Komatsu distributor.

If you sell the machine, be sure to give this manual to the new owners together with the machine.

Komatsu delivers machines that comply with all applicable regulations and standards of the country to

which it has been shipped. If this machine has been purchased in another country or purchased from

someone in another country, it may lack certain safety devices and specifications that are necessary for

use in your country. If there is any question about whether your product complies with the applicable

standards and regulations of your country, consult Komatsu or your Komatsu distributor before operating

the machine.

Storage location for the Operation and Maintenance

Manual:

magazine box on the left side of the operator's seat.

FOREWORD SAFETY INFORMATION

1-3

SAFETY INFORMATION 1

To enable you to use this machine safely, safety precautions and labels are given in this manual and affixed to the

machine to give explanations of situations involving potential hazards and of the methods of avoiding such situa-

tions.

Signal words

The following signal words are used to inform you that there is a potential hazardous situation that may lead to per-

sonal injury or damage.

In this manual and on machine labels, the following signal words are used to express the potential level of hazard.

Example of safety message using signal word

WARNING

When standing up from the operator's seat, always place

the safety lock lever in the LOCK position.

If you accidentally touch the control levers when they are

not locked, this may cause a serious injury or death.

Other signal words

In addition to the above, the following signal words are used to indicate precautions that should be followed to pro-

tect the machine or to give information that is useful to know.

Indicates an imminently hazardous situation which, if not avoided, will result in death

or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death

or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury. This word is used also to alert against unsafe practices that may

cause property damage.

DANGER

WARNING

CAUTION

NOTICE This word is used for precautions that must be taken to avoid actions which could shorten

the life of the machine.

REMARKS This word is used for information that is useful to know.

SAFETY INFORMATION FOREWORD

1-4

qSafety labels

Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying

out operation or maintenance of the machine that may involve hazard.

This machine uses “Safety labels using words“ and “Safety labels using pictograms“ to indicate safety procedures.

Example of safety label using words

Safety labels using pictogram

Safety pictograms use a picture to express a level of hazard-

ous condition equivalent to the signal word. These safety pic-

tograms use pictures in order to let the operator or

maintenance worker understand the level and type of hazard-

ous condition at all times.

Safety pictograms show the type of hazardous condition at the

top or left side, and the method of avoiding the hazardous con-

dition at the bottom or right side. In addition, the type of haz-

ardous condition is displayed inside a triangle and the method

of avoiding the hazardous condition is shown inside a circle.

Komatsu cannot predict every circumstance that might involve a potential hazard in operation and maintenance.

Therefore, the safety messages in this manual and on the machine may not include all possible safety precau-

tions.

If any procedures or actions not specifically recommended or allowed in this manual are used, it is your responsi-

bility to take the necessary steps to ensure safety.

In no event should you engage in prohibited uses or actions described in this manual.

The explanations, values, and illustrations in this manual were prepared based on the latest information available

at that time. Continuing improvements in the design of this machine can lead to changes in detail which may not

be reflected in this manual. Consult Komatsu or your Komatsu distributor for the latest available information of

your machine or for questions regarding information in this manual.

The numbers in circles in the illustrations correspond to the numbers in ( ) in the text. (For example: 1-> (1))

FOREWORD SAFETY INFORMATION

1-5

Noise emission levels 1

Two labels indicating the machine noise level are affixed on the

machine

qSound pressure level at the operator’s station, measured

according to ISO6396 (Dynamic test method, simulated

working cycle).

qSound power level emitted by the machine, measured

according to ISO 6395 (Dynamic test method, simulated

working cycle). This is the guaranteed value as specified

in European directive 2000/14/EC.

Vibration levels 1

When used for its intended purpose, levels of vibration for the earth-moving machine transmitted from the opera-

tor’s seat are lower than or equal to the tested vibrations for the relative machinery class in compliance with ISO

7096.

The actual acceleration value for the hands and arms is less than or equal to 2.5 m/s². The actual acceleration

value for the body is less than or equal to 0.5 m/s².

These values were determined using a representative machine and measured during the typical operating condi-

tion indicated below according to the measurement procedures that are defined in the standards ISO 2631/1 and

ISO 5349.

Operating condition: 1

(HYDRAULIC EXCAVATORS:) Excavating (Digging-loading-rotating-unloading-rotating)

SAFETY INFORMATION FOREWORD

1-6

Guide to Reduce Vibration Levels on Machine 1

The following guides can help an operator of this machine to reduce the whole body vibration levels:

1. Use the correct equipment and attachments.

2. Maintain the machine according to this manual

qTire pressures (for wheeled machines), tension of crawler (for crawler machines)

qBrake and steering systems

qControls, hydraulic system and linkages

3. Keep the terrain where the machine is working and traveling in good condition

qRemove any large rocks or obstacles

qFill any ditches and holes

qSite manager should provide machine operators with machine and schedule time to maintain terrain con-

ditions

4. Use a seat that meets ISO 7096 and keep the seat maintained and adjusted

qAdjust the seat and suspension for the weight and size of the operator

qWear seat belt

qInspect and maintain the seat suspension and adjustment mechanisms

5. Steer, brake, accelerate, shift gears (for wheeled machines), and move the attachment levers and pedals

slowly so that the machine moves smoothly

6. Adjust the machine speed and travel path to minimize the vibration level

qWhen pushing with bucket or blade, avoid sudden loading; load gradually

qDrive around obstacles and rough terrain conditions

qSlow down when it is necessary to go over rough terrain

qMake the curve radius of traveling path as large as possible

qTravel at low speed when traveling around sharp curves

7. Minimize vibrations for long work cycle or long distance traveling

qReduce speed to prevent bounce

qTransport machines long distances between worksites

8. The following guidelines can be effective to minimize risks of low back pain

qOperate the machine only when you are in good health.

qProvide breaks to reduce long periods of sitting in the same posture

qDo not jump down from the cab or machine

qDo not repeatedly handle and lift loads

FOREWORD INTRODUCTION

1-7

INTRODUCTION 1

This Komatsu machine is designed to be used mainly for the following work:

qDigging work

qLeveling work

qDitching work

qLoading work

qDemolition work

See the section “RECOMMENDED APPLICATIONS (3-100)“ for further details.

DIRECTIONS OF MACHINE 1

In this manual, the terms front, rear, left, and right refer to the travel direction as seen from the operator's seat

when the operator's seat is facing the front and the sprocket is at the rear of the machine.

BREAKING-IN THE NEW MACHINE

NOTICE

Your Komatsu machine has been thoroughly adjusted and tested before shipment from the factory. How-

ever, operating the machine under full load before breaking the machine in can adversely affect the perfor-

mance and shorten the machine life.

Be sure to break in the machine for the initial 100 hours (as indicated on the service meter).

Make sure that you fully understand the content of this manual, and pay careful attention to the following points

when breaking in the machine.

qRun the engine at idling for 15 seconds after starting it. During this time, do not operate the control levers or

fuel control dial.

qIdle the engine for 5 minutes after starting it up.

qAvoid operation with heavy loads or at high speeds.

qImmediately after starting the engine, avoid sudden starts, sudden acceleration, unnecessary sudden stops,

and sudden changes in direction.

Front

Right

Sprocket

Rear

Left

Operator’s seat

PRODUCT INFORMATION FOREWORD

1-8

PRODUCT INFORMATION 1

When requesting service or ordering replacement parts, please

inform your Komatsu distributor of the following items.

PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO. PLATE 1

On the bottom right of the operator's cab

The design of the nameplate differs according to the territory.

ENGINE SERIAL NUMBER PLATE AND ITS LOCATION 1

On the upper side of the engine cylinder head cover.

EPA: Environmental Protection Agency, U.S.A.

Andere Handbücher für PC130-7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Komatsu Bagger Handbücher

Komatsu

Komatsu PC138USLC-11 Installationsanleitung

Komatsu

Komatsu PC1250-11 Bedienungsanleitung

Komatsu

Komatsu ecot3 PC228US-8 Installationsanleitung

Komatsu

Komatsu PC200-8 Bedienungsanleitung

Komatsu

Komatsu GD555-3C Installationsanleitung

Komatsu

Komatsu PC18MR-3 Installationsanleitung

Komatsu

Komatsu PC350LC-8 Handbuch

Komatsu

Komatsu HB215LC-3 Handbuch

Komatsu

Komatsu PC12R-8 Handbuch

Komatsu

Komatsu PC600LC-7 Backhoe Bedienungsanleitung

Komatsu

Komatsu WA900-3E0 Installationsanleitung

Komatsu

Komatsu PC490LC-11 Handbuch

Komatsu

Komatsu PC27R-8 DELUXE Installationsanleitung

Komatsu

Komatsu PC78US-6 Handbuch

Komatsu

Komatsu PC600 - Bedienungsanleitung

Komatsu

Komatsu PC220-8 Bedienungsanleitung

Komatsu

Komatsu PC05-6 Installationsanleitung

Komatsu

Komatsu GD511A-1 Handbuch

Komatsu

Komatsu PC350LC-8 Installationsanleitung

Komatsu

Komatsu PC350LC-8 Handbuch

Komatsu

Komatsu PC160LC -7E0 Installationsanleitung

Komatsu

Komatsu PC200 -8 Installationsanleitung

Komatsu

Komatsu ecot3 PC300LC-8 Installationsanleitung

Komatsu

Komatsu PC128UU-2 Handbuch

Beliebte Bagger Handbücher anderer Marken

Hyundai

Hyundai Robex 210LC-9 Bedienungsanleitung

Hitachi

Hitachi Zaxis 110 Zaxis 125US Gebrauchsanweisung

sennebogen

sennebogen 830 E Bedienungsanleitung

Topcon

Topcon X-63 Gebrauchs- und Pflegehandbuch

Hitachi

Hitachi ZX27U-2 Bedienungsanleitung

jcb

jcb 15c-1 Bedienungsanleitung

Case

Case CX290B Bedienungsanleitung

SUNWARD

SUNWARD SWE155F Handbuch

CNH

CNH CX16B Bedienungsanleitung

Super Products

Super Products MUD DOG 700 Bedienungsanleitung

New Holland

New Holland E57C Bedienungsanleitung

Hyundai

Hyundai Robex 160LC-9 Bedienungsanleitung

Doosan

Doosan DX180LC Installationsanleitung

Hyundai

Hyundai HW65AH Bedienungsanleitung

mecalac

mecalac 14 MBX Bedienungsanleitung

CASE CONSTRUCTION

CASE CONSTRUCTION CX350C Bedienungsanleitung

Hyundai

Hyundai Robex 140LC-9 Bedienungsanleitung

Case

Case CX50B Bedienungsanleitung