Komatsu PC160LC-8 Handbuch

PC160LC-8

PC190LC-

PC190NLC-8

SERIALNUMBER

PC160LC-8-K50001andup

PC190LC-8-K50001andup

PC190NLC-8-K50001andup

HYDRAULIC EXCAVATOR

Unsafe use of this machine may cause serious injury or

death. Operators and maintenance personnel must read

this manual before operating or maintaining this

machine. This manual should be kept inside the cab for

reference and periodically reviewed by all personel who

will come into contact with the machine.

Operation &

Maintenance Manual

UENAM00773

WARNING

ORIGINAL INSTRUCTIONS

Find manuals at https://best-manuals.com

FOREWORD

Find manuals at https://best-manuals.com

FOREWORD FOREWORD

1-2

FOREWORD 1

This manual provides rules and guidelines which will help you use this machine safely and effectively. The pre-

cautions in this manual must be followed at all times when performing operation and maintenance. Most accidents

are caused by the failure to follow fundamental safety rules for the operation and maintenance of machines. Acci-

dents can be prevented by knowing beforehand conditions that may cause a hazard when performing operation

and maintenance.

WARNING

Before beginning operation or maintenance, operators and maintenance personnel must always observe

the following points.



Read this manual thoroughly and understand its contents fully.



Read the safety messages and safety labels given in this manual carefully so that they should be under-

stood fully.



Keep this manual at the storage location for the Operation and Maintenance Manual given below so that

all personnel involved in working on the machine can consult it periodically.



In case this manual should be lost or damaged, immediately contact Komatsu or your Komatsu distributor

to obtain a new copy.



When you sell the machine, make sure that this manual should be provided to the new owner together

with the machine.



In this manual, measurements are expressed in international standard units (SI). For the reference pur-

pose, weight units used in the past are also displayed in ( ).

Storage location for the Operation and Maintenance Manual:

magazine box on the left side of the operator's seat.

Find manuals at https://best-manuals.com

FOREWORD SAFETY INFORMATION

1-3

SAFETY INFORMATION 1

To enable you to use this machine safely, safety precautions and labels are given in this manual and affixed to the

machine to give explanations of situations involving potential hazards and of the methods of avoiding such situa-

tions.

Signal words

The following signal words are used to inform you that there is a potential hazardous situation that may lead to per-

sonal injury or damage.

In this manual and on machine labels, the following signal words are used to express the potential level of hazard.

Example of safety message using signal word

WARNING

When standing up from the operator's seat, always place the lock lever in the LOCK position.

If you accidentally touch the control levers when they are not locked, this may cause a serious injury or

death.

Other signal words

In addition to the above, the following signal words are used to indicate precautions that should be followed to pro-

tect the machine or to give information that is useful to know.

Indicates an imminently hazardous situation which, if not avoided, will result in death

or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death

or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury. This word is used also to alert against unsafe practices that may

cause property damage.

NOTICE This word is used for precautions that must be taken to avoid actions which could shorten

the life of the machine.

REMARKS This word is used for information that is useful to know.

DANGER

WARNING

CAUTION

Find manuals at https://best-manuals.com

SAFETY INFORMATION FOREWORD

1-4

qSafety labels

Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying

out operation or maintenance of the machine that may involve hazard.

This machine uses “Safety labels using pictograms“ to indicate safety procedures.

Safety labels using pictogram

Safety pictograms use a picture to express a level of hazard-

ous condition equivalent to the signal word. These safety picto-

grams use pictures in order to let the operator or maintenance

worker understand the level and type of hazardous condition at

all times. Safety pictograms show the type of hazardous condi-

tion at the top or left side, and the method of avoiding the haz-

ardous condition at the bottom or right side. In addition, the

type of hazardous condition is displayed inside a triangle and

the method of avoiding the hazardous condition is shown

inside a circle.

Komatsu cannot predict every circumstance that might involve a potential hazard in operation and maintenance.

Therefore, the safety messages in this manual and on the machine may not include all possible safety precau-

tions.

If any procedures or actions not specifically recommended or allowed in this manual are used, it is your responsi-

bility to take the necessary steps to ensure safety.

In no event should you engage in prohibited uses or actions described in this manual.

The explanations, values, and illustrations in this manual were prepared based on the latest information available

at that time. Continuing improvements in the design of this machine can lead to changes in detail which may not

be reflected in this manual. Consult Komatsu or your Komatsu distributor for the latest available information of

your machine or for questions regarding information in this manual.

The numbers in circles in the illustrations correspond to the numbers in ( ) in the text. (For example: -> (1))

Part No.

Find manuals at https://best-manuals.com

FOREWORD SAFETY INFORMATION

1-5

NOISE (PC160LC) 1

Two labels indicating the machine noise level are affixed on the machine.

qSound pressure level at the operator’s station, measured

according to ISO6396 (Dynamic test method, simulated

working cycle).

The maximum value of the standard deviation of the meas-

ured time-averaged A-weighted emission sound pressure

level at the operator's position is 2.5 dB, in accordance with

ISO 11201.

qSound power level emitted by the machine, measured

according to ISO 6395 (Dynamic test method, simulated

working cycle). This is the guaranteed value as specified in

European directive 2000/14/EC.

This value includes an uncertainty of 0.27 dB.

Find manuals at https://best-manuals.com

SAFETY INFORMATION FOREWORD

1-6

NOISE (PC190LC,190NLC) 1

Two labels indicating the machine noise level are affixed on the machine.

qSound pressure level at the operator’s station, measured

according to ISO6396 (Dynamic test method, simulated

working cycle).

The maximum value of the standard deviation of the meas-

ured time-averaged A-weighted emission sound pressure

level at the operator's position is 2.5 dB, in accordance with

ISO 11201.

qSound power level emitted by the machine, measured

according to ISO 6395 (Dynamic test method, simulated

working cycle). This is the guaranteed value as specified in

European directive 2000/14/EC

This value includes an uncertainty of 0.27 dB.

Vibration levels for PC160 and PC190-8 1

When used for its intended purpose, levels of vibration for the earth-moving machine transmitted from the opera-

tor’s seat are lower than or equal to the tested vibrations for the relative machinery class in compliance with ISO

7096.

The actual acceleration value for the hands and arms is less than or equal to 2.5 m/s², the uncertainty for this

value is 0.48 m/s² according to EN12096:1997.

The actual acceleration value for the body is less than or equal to 0.5 m/s², the uncertainty for this value is 0.23 m/

s² according to EN12096:1997.

These values were determined using a representative machine and measured during the typical operating condi-

tion indicated below according to the measurement procedures that are defined in the standards ISO 2631/1 and

ISO 5349.

Find manuals at https://best-manuals.com

FOREWORD SAFETY INFORMATION

1-7

Operating condition:

Excavating (Digging-loading-rotating-unloading-rotating)

Guide to Reduce Vibration Levels on Machine 1

The following guides can help an operator of this machine to reduce the whole body vibration levels:

1. Use the correct equipment and attachments.

2. Maintain the machine according to this manual

QTension of crawler (for crawler machines)

QBrake and steering systems

QControls, hydraulic system and linkages

3. Keep the terrain where the machine is working and travelling in good condition

QRemove any large rocks or obstacles

QFill any ditches and holes

QSite manager should provide machine operators with machine and schedule time to maintain terrain con-

ditions

4. Use a seat that meets ISO 7096 and keep the seat maintained and adjusted

QAdjust the seat and suspension for the weight and size of the operator

QWear seat belt

QInspect and maintain the seat suspension and adjustment mechanisms

5. Steer, brake, accelerate, and move the attachment levers and pedals slowly so that the machine moves

smoothly

6. Adjust the machine speed and travel path to minimize the vibration level

QWhen pushing with bucket or blade, avoid sudden loading; load gradually

QDrive around obstacles and rough terrain conditions

QSlow down when it is necessary to go over rough terrain

QMake the curve radius of travelling path as large as possible

QTravel at low speed when travelling around sharp curves

7. Minimize vibrations for long work cycle or long distance travelling

QReduce speed to prevent bounce

QTransport machines long distances between worksites

8. The following guidelines can be effective to minimize risks of low back pain

QOperate the machine only when you are in good health.

QProvide breaks to reduce long periods of sitting in the same posture

QDo not jump down from the cab or machine

QDo not repeatedly handle and lift loads

Find manuals at https://best-manuals.com

INTRODUCTION FOREWORD

1-8

INTRODUCTION 1

This Komatsu machine is designed to be used mainly for the following work:

qDigging work

qLevelling work

qDitching work

qLoading work

See the section RECOMMENDED APPLICATIONS (3-168) for further details.

DEMOLITION WORK 1

WARNING

qA demolition machine is a machine based on earth

moving machinery (see EN ISO 6165) and including

equipment and attachment (working tool - e.g. proces-

sor or breaker) specifically designed to demolish, cut,

loosen, separate, pick up, transport component parts

of buildings or civil engineering structures.

qThis machine is not prepared for use in demolition.

qUsing this machine in demolition work gives an

increased risk of serious injury or death.

qAll Komatsu machines that are specifically designed

and can be used for demolition work, will display the

Komatsu demolition decal.

qIf the machinery does not display this decal and it is

necessary to carry out demolition work, contact your

distributor for information on demolition machinery

compliant with the applicable standards.

Find manuals at https://best-manuals.com

Andere Handbücher für PC160LC-8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Komatsu Bagger Handbücher

Komatsu

Komatsu PC600LC-8 BACKHOE Bedienungsanleitung

Komatsu

Komatsu PC18MR-3 Installationsanleitung

Komatsu

Komatsu PC220-7 - Bedienungsanleitung

Komatsu

Komatsu PW98MR-10 Handbuch

Komatsu

Komatsu PC850-8 BACKHOE Bedienungsanleitung

Komatsu

Komatsu PC400LC-8 Handbuch

Komatsu

Komatsu Breathesafe WA900-3EO Installationsanleitung

Komatsu

Komatsu PC130-7 Installationsanleitung

Komatsu

Komatsu PC400-8 Bedienungsanleitung

Komatsu

Komatsu PC290LL-11 Installationsanleitung

Komatsu

Komatsu PC270LL-7L Handbuch

Komatsu

Komatsu PC210LC-10 DEMOLITION BASE SPEC. Handbuch

Komatsu

Komatsu PW160-7H Handbuch

Komatsu

Komatsu Galeo PC14R-2 Handbuch

Komatsu

Komatsu PC75R-2 Installationsanleitung

Komatsu

Komatsu PC200- 300001 Installationsanleitung

Komatsu

Komatsu Galeo PC400-8R Bedienungsanleitung

Komatsu

Komatsu PC45MR-5 Bedienungsanleitung

Komatsu

Komatsu HB215LC-2 Installationsanleitung

Komatsu

Komatsu ecot3 PC160LC-8 Installationsanleitung

Komatsu

Komatsu Galeo PC138US-8 Bedienungsanleitung

Komatsu

Komatsu PC160LC-8 Bedienungsanleitung

Komatsu

Komatsu PC09-1 Installationsanleitung

Komatsu

Komatsu PC300LC-8 Handbuch

Beliebte Bagger Handbücher anderer Marken

Hyundai

Hyundai Robex 210LC-9 Bedienungsanleitung

Hitachi

Hitachi Zaxis 110 Zaxis 125US Gebrauchsanweisung

sennebogen

sennebogen 830 E Bedienungsanleitung

Topcon

Topcon X-63 Gebrauchs- und Pflegehandbuch

Hitachi

Hitachi ZX27U-2 Bedienungsanleitung

jcb

jcb 15c-1 Bedienungsanleitung

Case

Case CX290B Bedienungsanleitung

SUNWARD

SUNWARD SWE155F Handbuch

CNH

CNH CX16B Bedienungsanleitung

Super Products

Super Products MUD DOG 700 Bedienungsanleitung

New Holland

New Holland E57C Bedienungsanleitung

Hyundai

Hyundai Robex 160LC-9 Bedienungsanleitung

Doosan

Doosan DX180LC Installationsanleitung

Hyundai

Hyundai HW65AH Bedienungsanleitung

mecalac

mecalac 14 MBX Bedienungsanleitung

CASE CONSTRUCTION

CASE CONSTRUCTION CX350C Bedienungsanleitung

Hyundai

Hyundai Robex 140LC-9 Bedienungsanleitung

Case

Case CX50B Bedienungsanleitung