Komatsu PC600-6 Bedienungsanleitung

1 - 1

FOREWORD

This manual provides rules and guidelines which will help you use this machine safely and effectively. The

precautions in this manual must be followed at all times when performing operation and maintenance. Most

accidents are caused by the failure to follow fundamental safety rules for the operation and maintenance of

machines. Accidents can be prevented by knowing beforehand conditions that may cause a hazard when

performing operation and maintenance.

WARNING

Operators and maintenance personnel must always do as follows before beginning operation or maintenance.

Always be sure to read and understand this manual thoroughly before performing operation and maintenance.

Read the safety messages given in this manual and the safety labels affixed to the machine thoroughly and be sure that you

understand them fully.

Keep this manual at the storage location for the Operation and Maintenance Manual given below, and have all personnel read it

periodically.

If this manual has been lost or has become dirty and cannot be read, request a replacement manual immediately from Komatsu

or your Komatsu distributor.

If you sell the machine, be sure to give this manual to the new owners together with the machine.

Komatsu delivers machines that comply with all applicable regulations and standards of the country to which it has been shipped.

If this machine has been purchased in another country or purchased from someone in another country, it may lack certain safety

devices and specifications that are necessary for use in your country. If there is any question about whether your product

complies with the applicable standards and regulations of your country, consult Komatsu or your Komatsu distributor before

operating the machine.

Storage location for the Operation and Maintenance Manual:

Manual luggage box behind operator's seat

1 - 2

FOREWORD FOREWORD

1-3

FOREWORD FOREWORD

1-4

FOREWORD SAFETY INFORMATION

SAFETY INFORMATION

To enable you to use this machine safely, safety precautions and labels are given in this manual and affixed to the

machine to give explanations of situations involving potential hazards and of the methods of avoiding such

situations.

Signal words

The following signal words are used to inform you that there is a potential hazardous situation that may lead to

personal injury or damage.

In this manual and on machine labels, the following signal words are used to express the potential level of hazard.

Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury. This word is used also to alert against unsafe practices that may cause

property damage.

Example of safety message using signal word

WARNING

When standing up from the operator's seat, always place the safety lock

lever in the LOCK position.

If you accidentally touch the control levers when they are not locked, this

may cause a serious injury or death.

Other signal words

In addition to the above, the following signal words are used to indicate precautions that should be followed to

protect the machine or to give information that is useful to know.

This word is used for precautions that must be taken to avoid actions which could shorten

the life of the machine.

This word is used for information that is useful to know.

1 - 5

FOREWORD

SAFETY INFORMATION

Safety labels

Safety labels are affixed to the machine to inform the operator or maintenance worker on the spot when carrying out

operation or maintenance of the machine that may involve hazard.

This machine uses "Safety labels using words" and "Safety labels using pictograms" to indicate safety procedures.

Example of safety label using words

Safety labels using pictogram

Safety pictograms use a picture to express a level of hazardous

condition equivalent to the signal word. These safety pictograms

use pictures in order to let the operator or maintenance worker

understand the level and type of hazardous condition at all times.

Safety pictograms show the type of hazardous condition at the top

or left side, and the method of avoiding the hazardous condition at

the bottom or right side. In addition, the type of hazardous condition

is displayed inside a triangle and the method of avoiding the

hazardous condition is shown inside a circle.

Komatsu cannot predict every circumstance that might involve a potential hazard in operation and maintenance.

Therefore, the safety messages in this manual and on the machine may not include all possible safety precautions.

If any procedures or actions not specifically recommended or allowed in this manual are used, it is your responsibility

to take the necessary steps to ensure safety.

In no event should you engage in prohibited uses or actions described in this manual.

The explanations, values, and illustrations in this manual were prepared based on the latest information available

at that time. Continuing improvements in the design of this machine can lead to changes in detail which may not

be reflected in this manual. Consult Komatsu or your Komatsu distributor for the latest available information of your

machine or for questions regarding information in this manual.

The numbers in circles in the illustrations correspond to the numbers in ( ) in the text. (For example: 1-> (1))

1 - 6

FOREWORD INTRODUCTION

INTRODUCTION

This Komatsu machine is designed to be used mainly for the following work:

Digging work

Leveling work

Ditching work

Loading work

Demolition work

See the section "RECOMMENDED APPLICATIONS (PAGE 3-93)" for further details.

DIRECTIONS OF MACHINE

In this manual, the terms front, rear, left, and right refer to the travel direction as seen from the operator's seat when

the operator's seat is facing the front and the sprocket is at the rear of the machine.

BREAKING-IN THE NEW MACHINE

NOTICE

Your Komatsu machine has been thoroughly adjusted and tested before shipment from the factory. However, operating the

machine under full load before breaking the machine in can adversely affect the performance and shorten the machine life.

Be sure to break in the machine for the initial 100 hours (as indicated on the service meter).

Make sure that you fully understand the content of this manual, and pay careful attention to the following points when

breaking in the machine.

Run the engine at idling for 15 seconds after starting it. During this time, do not operate the control levers or fuel

control dial.

Idle the engine for 5 minutes after starting it up.

Avoid operation with heavy loads or at high speeds.

Immediately after starting the engine, avoid sudden starts, sudden acceleration, unnecessary sudden stops, and

sudden changes in direction.

1 - 7

FOREWORD

PRODUCT INFORMATION

When requesting service or ordering replacement parts, please inform your Komatsu distributor of the following

items.

MACHINE SERIAL NUMBER PLATE AND ITS LOCATION

On the front bottom right of the operator's cab (side of upper frame)

ENGINE SERIAL NUMBER PLATE AND ITS LOCATION

On the right side of the engine cylinder block has seen from the fan.

(The EPA auxiliary nameplate is on the top of the No. 5 cylinder head cover.)

EPA: Environmental Protection Agency, U.S.A.

1 - 8

FOREWORD PRODUCT INFORMATION

SERVICE METER LOCATION

On top of the machine monitor

YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR

Machine serial No.

Engine serial No.

Distributor name

Address

Service Personnel

Phone/Fax

1 - 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Komatsu Bagger Handbücher

Komatsu

Komatsu D51EXi -24 Installationsanleitung

Komatsu

Komatsu PC160LC-7KA Handbuch

Komatsu

Komatsu PC1250-8R - Bedienungsanleitung

Komatsu

Komatsu A12001 Installationsanleitung

Komatsu

Komatsu PC270LL-7L Handbuch

Komatsu

Komatsu Galeo PC400-7 Bedienungsanleitung

Komatsu

Komatsu PC210-8 Handbuch

Komatsu

Komatsu PC45MR-5 Bedienungsanleitung

Komatsu

Komatsu PC27R-8 DELUXE Installationsanleitung

Komatsu

Komatsu PC220-7 - Bedienungsanleitung

Komatsu

Komatsu PC600LC-8R BACKHOE Bedienungsanleitung

Komatsu

Komatsu GALEO PC1250-8 Handbuch

Komatsu

Komatsu Galeo PC138US-8 Installationsanleitung

Komatsu

Komatsu PW160-7K Series Bedienungsanleitung

Komatsu

Komatsu PC220-8 Bedienungsanleitung

Komatsu

Komatsu PC20R-8 Installationsanleitung

Komatsu

Komatsu PC450LC-8 Handbuch

Komatsu

Komatsu GD610 Series Installationsanleitung

Komatsu

Komatsu GALEO PC200 Bedienungsanleitung

Komatsu

Komatsu PC290LC-11 Handbuch

Komatsu

Komatsu WA270-3H Handbuch

Komatsu

Komatsu PC1250 - Bedienungsanleitung

Komatsu

Komatsu PC2000-8 BACKHOE Handbuch

Komatsu

Komatsu PC490LC-10 Handbuch

Beliebte Bagger Handbücher anderer Marken

Hyundai

Hyundai Robex 210LC-9 Bedienungsanleitung

Hitachi

Hitachi Zaxis 110 Zaxis 125US Gebrauchsanweisung

sennebogen

sennebogen 830 E Bedienungsanleitung

Topcon

Topcon X-63 Gebrauchs- und Pflegehandbuch

Hitachi

Hitachi ZX27U-2 Bedienungsanleitung

jcb

jcb 15c-1 Bedienungsanleitung

Case

Case CX290B Bedienungsanleitung

SUNWARD

SUNWARD SWE155F Handbuch

CNH

CNH CX16B Bedienungsanleitung

Super Products

Super Products MUD DOG 700 Bedienungsanleitung

New Holland

New Holland E57C Bedienungsanleitung

Hyundai

Hyundai Robex 160LC-9 Bedienungsanleitung

Doosan

Doosan DX180LC Installationsanleitung

Hyundai

Hyundai HW65AH Bedienungsanleitung

mecalac

mecalac 14 MBX Bedienungsanleitung

CASE CONSTRUCTION

CASE CONSTRUCTION CX350C Bedienungsanleitung

Hyundai

Hyundai Robex 140LC-9 Bedienungsanleitung

Case

Case CX50B Bedienungsanleitung