Konica Minolta Bizhub C364 Bedienungsanleitung

E-1

INSTALLATION MANUAL

A161-9601-01

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Caution:

• For the detailed installation procedures for each

option, follow the instructions given in the corre-

sponding installation manual and perform the

procedures correctly. (Optional devices must be

installed after completing the main unit installa-

tion.)

• When placing the machine on the floor, make

sure to use the paper feed cabinet or the desk

to secure the performance and the quality of

the product.

• To use this machine, install the dual scan docu-

ment feeder, the reverse automatic document

feeder, or the original cover.

Even if you do not install the original cover, be

sure to install the hinge covers supplied with

the original cover.

• Once the Power Switch is turned ON, do not

turn OFF it until the installation work has been

completed.

• Lifting the machine in an awkward position or

transporting it in a poorly balanced position

could result in personal injury. When transport-

ing the machine, assign an adequate number of

persons to the job and ensure that each person

can take a good position of not being exces-

sively loaded.

(mass: approx. 85 kg (187-3/8 lb))

*1: When installing the AU-201

with MK-735

*2: When installing the AU-201

without MK-735

*3: No particular order in installa-

tion procedures.

*4: Unable to be installed in

C224.

UK-204*3

PC-110 PC-210 DK-705

JS-506

Machine

PC-410

SP-501 OC-511DF-701

PK-520

SD-511

MK-730

AU-102

FS-534

Electronic system options

FS-533

PK-519

MK-735

EK-606*3 EK-607*3

SC-508*3

FK-511*3

VI-506*4

IC-414*4

DK-510

MK-734

HT-509

WT-506

AU-201*2

DF-624

AU-201*1

KH-102

✱Electronic system options

A161IXC001DA

Applied Machines: / /

E-2

II. Installation space (unit: mm (inch))

bizhub C364 + DF-701 + PC-210 + FS-534

+ MK-730

III. Pre-installation check items

1. Select a level and stable place for installing the

machine.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Notes on using touch panel

Be sure to instruct users on the following points.

• This machine uses a capacitive touch panel.

When you touch the touch panel, use your fin-

ger or the stylus pen supplied with the machine.

If you touch the panel using your nail or a pen

tip instead of using your finger or the stylus pen,

the touch panel does not respond normally.

• Pressing the touch panel hard may cause dam-

age.

• Do not strongly press the panel or press it using

the sharp tip of mechanical pencils.

• The key is a finger tapping (quick light touch

using a finger) operation.

A161IXC002DA

937

(36-7/8)

225

(8-7/8)

1822

(71-3/4)

660

(26)

1246

(49-1/16)

428

(16-7/8)

818

(32-3/16)

1553

(61-1/8)

386

(15-3/16)

921

(36-1/4)

246

(9-11/16)

E-3

V. Accessory parts

* Varies depending on the applicable marketing

area.

Note:

Keep the label (Super G3 label) at hand. It is nec-

essary for mounting the FAX Kit.

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

VI. Removing the machine

1. Unpack and remove the machine package.

2. Remove the machine, holding it by the locations

on the left side and the handles on the right side

as shown in the illustration and keeping it level.

Caution:

Machine mass: approx. 85 kg/187-3/8 lb

• Make available collective manpower of an

appropriate size for transporting the machine.

• When attaching the machine, as the reference

fit the machine with the corner A and B of the

paper feed cabinet.

No. Name Q’ty

1. User’s guide holder 1

2. Quick start guide 1

3. Quick assist guide 1

4. Installation manual 1 set

5. User’s guide CD 1

6. CD-ROM 1 set

7. Paper size label 1

8. Label (Legal restrictions on copying) * 1

9. Label (Super G3 label) 1

10. Panel sheet 1

11. Cap A (Black) 2

12. Cap B (White) 2

13. Power cord * 1

14. Power cord instruction * 1

15. Cord clamp * 2

16. Screw A * 1

17. Screw B *

18. Spacer 1

19. Stylus pen 1

20. Waste toner box 1

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

9738

A161IXC061DA

When holding the transportation handles,

be careful not to catch your fingers in the

machine.

A2XMIXC007DA

BA2XMIXC058DA

E-4

VII. Removing protective tape, packing

and other shipping materials

1. Remove the protective tape and the protective

materials.

2. Open the right door and remove the packaging

materials.

Note:

After removing the packaging materials, make

sure that the transfer roller assy is secured in

place. In the case of <NG>, press the transfer

roller assy into place so that it is secured as shown

in <OK>.

3. Remove the locking screws.

4. Remove the protective sheets.

A161IXC003DA

A161IXC004DA

A161IXC045DA

A161IXC048DA

A161IXC005DA

< OK > < NG >

A161IXC006DA

A161IXC007DA

E-5

5. Slide out the tray 1 and remove the protective

tape from the inside of the tray.

6. Slide out the tray 2 and remove the tray locking

materials.

7. Remove the protective tapes from the inside of

the tray 2 and remove accessory parts.

8. Open the front door.

9. Remove the protective tape and protective mate-

rial.

10. Remove the protective tape from the drum units

and developing units.

Note:

Do not remove the tape A in this procedure.

11. Remove the protective materials from the four

places.

Note:

Keep the protective materials. It is necessary for

transporting the machine.

A161IXC008DA

A161IXC009DA

A161IXC036DA

A161IXC015DB

A161IXC010DC

Protective tape

Protective material

A161IXC059DA

A161IXC011DB

E-6

12. Release the lever of the drum unit (K).

13. Slightly slide the drum unit (K) out and remove

the protective tape.

14. Slide the drum unit (K) into the machine.

15. Lock the drum unit (K) with the lever.

16. Install the supplied waste toner box.

Note:

Push the areas indicated by the “ ” marks to set

the waste toner box to the machine.

VIII. Installing the toner cartridge

Note:

Since cartridge is not supplied with the machine,

purchase toner cartridge (of different colors) sepa-

rately.

1. Shake the toner cartridge up and down and left to

right 5 to 10 times respectively.

Note:

Shake the cartridge adequately. Otherwise, it may

cause trouble.

2. Insert the toner cartridge into the machine.

Note:

• Make sure that the color is same between

inserting port and the toner cartridge.

• Make sure that the blue label position of the

toner cartridge is matched with the one of the

machine side.

A161IXC012DB

A161IXC013DB

A161IXC014DB

A0EDIXC020DA

A161IXC055DA

E-7

3. Push the toner cartridge all the way in and rotate

it clockwise to lock it.

Note:

Make sure that the toner cartridge is pushed all the

way in.

4. Using the same procedure, install the toner car-

tridges for other colors of toner.

5. Close the front door.

IX. Mounting the accessory parts

1. Attach the supplied caps A and B.

2. Remove the protective cover from the supplied

stylus pen.

Note:

Discard the removed protective cover.

3. Set the stylus pen in the place shown in the illus-

tration.

4. Attach the supplied cord clamp to the scanner

rear cover of the machine. (One supplied screw

Note:

This may not be performed depending on the

applicable marketing area.

X. Connecting the power cord

Note:

Steps 1 and 2 may be unnecessary depending on

the applicable marketing area.

1. Connect the power cord.

A0EDIXC022DA

A161IXC016DA

A2X0IXC068DA

A161IXC017DB

A161IXE047DA

A161IXE042DA

E-8

2. Fit the supplied cord clamp over the power cord.

(One supplied screw B)

3. Plug the power cord into the power outlet.

XI. Toner supply

Turn ON the Main Power Switch.

Note:

• Toner is automatically supplied in parallel with

warm-up.

• If any one of the toner cartridges is not set,

toner supply does not start.

XII. Adjusting touch panel

1. Press the Menu key.

2. Touch “Accessibility.”

3. Touch “Touch Panel Adjustment.”

4. Using the stylus pen, lightly touch the center of

the + markers at four places on the touch panel.

(Any specific marker can be the first one.)

Note:

Pressing the touch panel hard may cause dam-

age.

* When all the markers at four places have been

touched, the start key turns blue and lights up

steadily blue.

5. Press the start key.

6. Touch “Close.”

XIII.Date/Time setting (Administrator set-

tings)

1. Select the Date/Time Setting function as follows:

Menu →Utility →Administrator Settings →Enter

the Administrator Password (Default setting:

1234567812345678) →System Settings →Date/

Time Settings.

2. Select the item you want to set and press the

clear key.

3. Enter the data for the year, month, day, and time-

of-day from the 10-key pad.

4. Touch “OK.”

5. Touch “Close” three times.

XIV. Setting gradation adjustment

Note:

Before starting the gradation adjustment, install

the optional dual scan document feeder, reverse

automatic document feeder, or original cover.

1. Set that A3 or Ledger paper is loaded in

the tray.

Note:

If the A3 or Ledger paper is not readily

available, use A4 or Letter paper.

2. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

3. Touch “Imaging Process Adjustment.”

4. Touch “Gradation Adjust.”

5. Check that “Stabilizer” is selected and press the

start key.

* When the start key lights up blue, go to step 6.

Note:

When a maintenance call occurs, see the service

manual.

A161IXE043DB

C4004U139CA

E-9

6. Touch “Print”, select “A3 /11×17 ”, and

press the start key.

A test pattern will then be produced on the A3

or Ledger paper.

7. Place the test pattern face down on the original

glass.

8. Place about ten sheets of A3 or Ledger

paper on the test pattern placed on the original

glass.

Lower the cover.

9. Press the start key.

The machine will start reading the test pattern.

10. When the machine completes reading the test

pattern, the “Gradation Adjust” screen will reap-

pear.

11. Repeat steps from 6 through 9 to let the

machine read the test pattern two times.

Note:

Steps 6 to 9 must be performed three times in total

including two repetitions.

12. Touch “Copy”, select “A3 /11×17 ”, and

press the start key.

A test pattern will then be produced on the

A3 or Ledger paper.

13. Place the test pattern face down on the original

glass.

14. Place about ten sheets of A3 or Ledger

paper on the test pattern placed on the original

glass.

Lower the cover.

15. Press the start key.

The machine will start reading the test pattern.

16. When the machine completes reading the test

pattern, the “Gradation Adjust” screen will reap-

pear.

17. Repeat steps from 12 through 15 to let the

machine read the test pattern two times.

Note:

Steps 12 to 15 must be performed three times in

total including two repetitions.

18. Touch “END.”

A161IXC021DA

Magenta

A161IXC022DA

A161IXC023DA

Cyan

A161IXC022DA

E-10

6. Touch “Print”, select “A4 /8½×11 ”, and

press the start key.

A test pattern will then be produced on the two

A4 or Letter papers.

7. Place the test pattern face down on the original

glass.

8. Place about ten sheets of A3 or Ledger

paper on the test pattern placed on the original

glass.

Lower the cover.

9. Press the start key.

The machine will start reading the test pattern.

10. When the machine completes reading the test

pattern, the “Gradation Adjust” screen will reap-

pear.

11. Repeat steps from 6 through 9 to let the

machine read the test pattern two times.

Note:

Steps 6 to 9 must be performed three times in total

including two repetitions.

12. Touch “Copy”, select “A4 /8½×11 ”, and

press the start key.

A test pattern will then be produced on the two

A4 or Letter papers.

13. Place the test pattern face down on the original

glass.

14. Place about ten sheets of A3 or Ledger

paper on the test pattern placed on the original

glass.

Lower the cover.

15. Press the start key.

The machine will start reading the test pattern.

16. When the machine completes reading the test

pattern, the “Gradation Adjust” screen will reap-

pear.

17. Repeat steps from 12 through 15 to let the

machine read the test pattern two times.

Note:

Steps 12 to 15 must be performed three times in

total including two repetitions.

18. Touch “END.”

A161IXC024DA

Magenta

A161IXC022DA

A161IXC025DA

Cyan

A161IXC022DA

Andere Handbücher für bizhub C364

Dieses Handbuch passt für folgende Modelle

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta 7115 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C451 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C360 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C350 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 162 Bedienungsanleitung

Konica Minolta

Konica Minolta Bizhub 4020 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C550 Series Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5450 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 215 Bedienungsanleitung

Konica Minolta

Konica Minolta IC-206 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C300 Montage- und Wartungsanleitung

Konica Minolta

Konica Minolta BIZHUB 162 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4690MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C20/C20X Originalbetriebsanleitung

Konica Minolta

Konica Minolta bizhub C35P Bedienungsanleitung

Konica Minolta

Konica Minolta 7013 Bedienungsanleitung

Konica Minolta

Konica Minolta DI2510 Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1390 MF Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1380 MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C754 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C360 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 20 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C452 Series Gebrauchsanweisung

Konica Minolta

Konica Minolta 7165 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta bizhub C364 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken