Konica Minolta Bizhub C654e Bedienungsanleitung

E-1

PK-520 Punch Kit

INSTALLATION MANUAL

A3ET-9550-01

Applied Machines: C754e/C654e/C754/C654/C554e/C454e/C364e/C284e/C224e/C554/C454/C364/C284/C224/

C368/C308/754e/654e/754/654/554e/454e/364e/284e/224e/367/287/227

COLOR MFP: 75 ppm/65 ppm/55 ppm/45 ppm/36 ppm/30 ppm/28 ppm/22 ppm

MFP: 75 ppm/65 ppm/55 ppm/45 ppm/36 ppm/28 ppm/22 ppm

Product Code: A2X0/A2X1/A5AY/A5C0/A5C1/A5C2/A5C4/A2XK/A4FJ/A161/A4FK/A4FM/A7PU/A7PY/A55V/

A5YN/A61D/A61E/A61F/A61G/A61H/A789/A7AH/A7AK

1. Accessory parts Note:

• This manual provides the illustrations of the

accessory parts and machine that may be

slightly different in shape from yours. In that

case, instead of the illustrations, use the

appearance of your machine to follow the

installation procedure. This does not cause any

significant change or problem with the proce-

dure.

• If none of the later steps instruct you to use the

parts including screw and cover that you

removed following the instructions described in

this manual, discard them.

2. Installation procedures

Note:

When mounting the punch kit, mount it before

mounting the finisher to the machine.

(1) Turn OFF the power switch and unplug the

power cord from the power outlet.

(2) Remove the protective tape.

No. Name Shape Q’ty

1. Punch unit

2. Punch box

3. Label

4. Installation

manual

set

Keep this bag away from babies and

children. Do not use in cribs, beds,

carriages, or playpens.

The thin film may cling to nose and

mouth and prevent breathing. This bag is

not a toy.

E-2

(3) If the Finisher FS-534SD or FS-534 is mounted

on the machine, remove the Finisher.

Note:

<C754e/C654e/C754/C654/C554e/C454e/C364e/

C284e/C224e/C554/C454/C364/C284/C224/C368/

C308/754e/654e/754/654/554e/454e/364e/284e/

224e>

See the installation manual for the Relay unit/Fin-

isher RU-513/FS-534SD or RU-513/FS-534 for

removal instructions.

<367/287/227>

See the installation manual for the Relay Unit/Fin-

isher RU-514/FS-534SD or RU-514/FS-534 for

removal instructions.

(4) Remove the rear cover from the finisher.

(Eight screws)

(5) Remove the screw and remove the guide plate.

(6) Insert the punch unit into the Finisher in the

place from which the guide plate was removed,

and secure the punch unit with the screw

removed in step (5).

(7) Connect the connector of the punch unit to the

board in the finisher.

(8) Route the harness of the punch unit through the

harness guides of the finisher.

Connector

Harness guide

E-3

(9) Install the supplied punch box.

(10) Affix the supplied label to the front door of the

finisher as shown in the illustration.

(11) Reattach the rear cover from the finisher

removed in step (4). (Eight screws)

(12) Install the finisher to the machine.

Note:

<C754e/C654e/C754/C654/C554e/C454e/C364e/

C284e/C224e/C554/C454/C364/C284/C224/C368/

C308/754e/654e/754/654/554e/454e/364e/284e/

224e>

See the installation manual for the Relay unit/Fin-

isher RU-513/FS-534SD or RU-513/FS-534 for

installation instructions.

<367/287/227>

See the installation manual for the Relay Unit/Fin-

isher RU-514/FS-534SD or RU-514/FS-534 for

installation instructions.

3. Configuration procedures

(1) Plug the power cord into the power outlet and

turn ON the power switch.

(2) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(3) Touch “Finisher.”

(4) Touch “Punch option setting.”

(5) Touch “PK-520” and select a desired number of

holes.

(6) Touch “decision.”

(7) Touch “END.”

(8) Touch “Exit” on the Service Mode screen.

(9) Turn OFF and ON the power switch.

4. Adjustment procedures

(1) Make a copy in the punch mode.

(Refer to the User’s Guide CD)

(2) Fold the copy into halves and check for possible

deviation in the punch hole positions.

Specifications: 0 ± 2.0 mm

Note:

If the positional deviation of the punch holes is not

within the accepted range, take the following

steps.

(3) Open the upper cover of the finisher.

E-4

(4) Loosen the two screws that hold the punch unit

in place.

(5) Using the triangle marks on the plate as a guide,

move the punch unit back and forth to adjust its

position.

(6) After the adjustment, tighten the two screws

loosened in step (4).

(7) Close the upper cover of the finisher.

(8) Make a copy and check the punch hole positions

again.

Note:

Perform this adjustment if necessary.

(1) Make a copy in the punch mode.

(Refer to the User’s Guide CD)

(2) Measure width A on the copy and check to see if

the measured dimension falls within the speci-

fied range.

Specifications: 9.5 ± 1.0 mm

<Europe: 4 holes>

Specifications: 11 ± 1.0 mm

<Sweden: 4 holes>

Specifications: 10.5 ± 1.0 mm

Note:

If the measured width A outside the specified

range, perform the following procedure to punch

hole position adjustment.

(3) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(4) Touch “Finisher.”

(5) Touch “FS-FN adjustment.”

(6) Touch “Punch Edge Adj.”

(7) Set the correction value using the /

keys.

• To make width A wider, enter a positive value.

• To make width A narrower, enter a negative

value.

<North America:

2 holes>

<North America:

3 holes>

<Europe: 4 holes> <Sweden: 4 holes>

E-5

(8) If the “Test Copy” button is displayed on the

adjustment screen, check the adjustment result

according to the following procedure.

a) Touch “Test Copy.”

b) Select the tray loading paper for the test copy.

c) Touch “3.”

d) Select the number of punch hole in the “Punch”

list, and then press the start key.

e) Check the punch hole positions.

f) Touch “END” to return to the adjustment

screen.

(9) Touch “END.”

(10) Touch “OK.”

(11) Touch “Exit” on the Service Mode screen.

(12) If you did not check the adjustment result in the

step (8), make a copy and check the punch

hole positions again.

Note:

Perform this adjustment if necessary.

(1) Make a copy in the punch mode.

(Refer to the User’s Guide CD)

(2) Check the tilt of the output paper.

Note:

If it tilts, follow the procedures below for punch

loop adjustment.

(3) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(4) Touch “Finisher.”

(5) Touch “FS-FN adjustment.”

(6) Touch “Punch Regist Loop Size.”

(7) Set the correction value using the /

keys.

• To make loop length larger, enter a positive

value.

• To make loop length smaller, enter a negative

value.

(8) Touch “END.”

(9) Touch “OK.”

(10) Touch “Exit” on the Service Mode screen.

(11) Make a copy again and check the deviance of

punch hole position.

Andere Handbücher für bizhub C654e

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta BIZHUB C250 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C280 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 361 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C300 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 181 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C300 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C650 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 751 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB PRO C6500 Leitfaden

Konica Minolta

Konica Minolta bizhub C452 Series Gebrauchsanweisung

Konica Minolta

Konica Minolta bizhub 751 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5450 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C368 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C25 Bedienungsanleitung

Konica Minolta

Konica Minolta PAGEPRO 1480MF Montageanleitung

Konica Minolta

Konica Minolta DF-606 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 500 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 750 Bedienungsanleitung

Konica Minolta

Konica Minolta Bizhub C3850 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C351 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C203 Series Beilage

Konica Minolta

Konica Minolta bizhub PRO 958 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 36 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4695MF Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta bizhub C654e Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken