Konica Minolta Bizhub C754e Bedienungsanleitung

E-1

INSTALLATION MANUAL

A2X0-9971-00

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Note:

• For the detailed installation procedures for each

option, follow the instructions given in the corre-

sponding installation manual and perform the

procedures correctly.

• Once the Power Switch is turned ON, do not

turn OFF it until the installation work has been

completed.

• When transporting the machine, assign an ade-

quate number of persons to the job and follow

the specified correct procedures.

(mass: approx. 221 kg (487-3/16 lb))

UK-204*1

Machine

Electronic system options

SP-501

EK-604*1 EK-605*1

SC-508*1

VI-506*1

IC-414*1

FK-511

MK-735

LU-204

LU-301

MK-715

OT-503

HT-508*2

KH-102

✱Electronic system options

WT-506

WT-509

AU-201

AU-102

ZU-606

PI-505

JS-602

FS-535

PK-521

SD-512

FS-534

PK-520SD-511

FS-534SD

*1: No particular order in installation procedures

*2: Varies depending on the applicable marketing area

FK-508*2 MK-728*2

KP-101

A2X0IXC001DA

Applied Machines: /

E-2

II. Installation space (unit: mm (inch))

bizhub C754e + ZU-606 + FS-535 + LU-204

III. Pre-installation check items

1. Select a level and stable place for installing the

machine.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Notes on using touch panel

Be sure to instruct users on the following points.

• This machine uses a capacitive touch panel.

When you touch the touch panel, use your fin-

ger or the stylus pen supplied with the machine.

If you touch the panel using your nail or a pen

tip instead of using your finger or the stylus pen,

the touch panel does not respond normally.

• Pressing the touch panel hard may cause dam-

age.

• Do not strongly press the panel or press it using

the sharp tip of mechanical pencils.

• The key is a finger tapping (quick light touch

using a finger) operation.

A2X0IXC002DA

498

(19-5/8)

1027

(40-7/16)

1155

(45-1/2)

495

(19-1/2)

1252

(49-5/16)

1575 (62-1/16)

1650 (64-15/16)

238

(9-3/8)

(2)

1066

(41-15/16)

2556 (100-5/8)

E-3

V. Accessory parts

* Varies depending on the applicable marketing

area

Note:

The parts shown below are used when installing

options. Keep them safe.

• Tray label/paper size label: Large capacity unit

(LU-301)

• Label (Super G3 label): Fax kit

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

VI. Unpacking the machine

Whether the slope is supplied with this machine or

not depends on your marketing areas. Follow the

notes below.

Note:

• When the slope is supplied with the machine,

follow the procedure, <A. When using the sup-

plied slope>.

• When the slope is not supplied with the

machine, follow the procedure, <B. When using

the jig slope>.

<A. When using the supplied slope>

1. Open the shipping box and remove the packag-

ing materials.

Note:

• Keep the supplied slope and cushion A that are

removed in this step for later use.

• The cushion B contains accessory parts.

Depending on the applicable marketing area,

the cushion B may also contain the power cord.

2. Remove the fixing materials (upper).

No. Name Q’ty

1. User’s guide holder 1

2. Quick start guide 1

3. Installation manual 1 set

4. User’s guide CD 1

5. CD-ROM 1 set

6. Tray label/Paper size label 1 set

7. Label (Legal restrictions on copying) * 1

8. Label (Super G3 label) 1

9. Panel sheet 1

10. Chart 1

11. Cap A (black) 2

12. Cap B (white) 2

13. Power cord * 1

14. Connector cover 1

15. Scanner cover 1

16. Mounting screw 1

17. Spacer 1

18. Power cord instruction * 1

19. Stylus pen 1

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

A2X0IXE053DA

Supplied slope

Cushion B

Cushion A

A2X0IXC004DA

E-4

3. Hold onto the handle of the machine and tilt the

machine to the right and left. Under this condition,

remove the fixing materials (lower).

4. Separate the cushion into two and install them to

the pallet (at two places).

5. Take out the slope and protective tape and

remove nails from the plastic bag.

6. Position the slope as illustrated and drive nails in

to fix the slope in position.

Caution:

Insert the nails in the outer holes.

7. Holding onto the front cover and the back panel

of the machine, slide the machine down along the

slope.

Caution:

Machine mass: 221 kg (487-3/16 lb)

• Perform this step on a level, stable site and

assign an adequate number of persons.

• When sliding the machine down, do not hold

onto the scanner portion.

• Do not insert your leg under the slope.

A2X0IXC005DB

A2X0IXE069DA

A2X0IXE054DA

A0P0IXC067DA

A2X0IXE055DA

Nail

A2X0IXE056DA

E-5

<B. When using the jig slope>

1. Open the shipping box and remove the packag-

ing materials.

Note:

• Do not use the corrugated cardboard as slope.

• The nails removed in this step are used in step

4 to hold the slope in place.

• The cushion shown in the illustration contains

the power cord and accessory parts.

2. Remove the fixing materials (upper).

3. Hold onto the handle of the machine and tilt the

machine to the right and left. Under this condition,

remove the fixing materials (lower).

4. Place the jig slope as shown and insert the nails

into the holes to fix the slope in position.

Caution:

• As the slope is not supplied with the machine,

prepare a jig slope.

• Make sure that the nails are inserted com-

pletely into the holes and the slope is held in

place.

A2X0IXC003DA

Nail

Cushion

Corrugated

cardboard

A2X0IXC004DA

A2X0IXC005DB

A2X0IXC051DB

A2X0IXC006DA

Nail

E-6

5. Holding onto the front cover and the back panel

of the machine, slide the machine down along the

slope.

Caution:

Machine mass: 221 kg (487-3/16 lb)

• Perform this step on a level, stable site and

assign an adequate number of persons.

• When sliding the machine down, do not hold

onto the scanner portion.

• Do not insert your leg under the slope.

VII. Removing protective tape, packing

and other shipping materials

1. Remove the protective tape and protective mate-

rials.

Note:

After removing protective tape B, be sure to lock

the lever.

A2X0IXC007DA

A2X0IXC008DB

A2X0IXC009DB

A2X0IXC011DB

A2X0IXC010DB

E-7

2. Open the right door and remove the protective

tape and the protective material.

3. Close the right door.

4. Remove the reinforcement plate. (Four screws)

5. Remove the locking screws.

6. Remove the protective sheet from the control

panel.

7. Pull the tray 1 out and remove the protective tape

from the tray.

8. Pull the tray 2 out and remove the protective tape

from the tray.

9. Pull trays 3 and 4 out and remove the desiccants.

A2X0IXC074DA

Protective tape/

Protective material

A2X0IXC012DB

A2X0IXC013DA

A2X0IXC014DA

A2X0IXC015DC

A2X0IXC016DC

A2X0IXC058DB

E-8

10. Remove the protective tape from trays 3 and 4.

11. Open the lower front door and remove the waste

toner box.

12. Remove the packing bracket. (One screw)

13. Install the waste toner box and close the lower

front door.

14. Open the upper front door and remove the pro-

tective tape.

VIII. Installing the toner cartridges

Note:

Since no toner cartridges are supplied with the

machine, purchase a toner cartridge (of different

colors) separately.

1. Shake the toner cartridge up and down five to ten

times.

Note:

Shake the cartridge adequately. Otherwise, it may

cause trouble.

2. Remove protective tape of the toner cartridge.

A2X0IXC076DA

A2X0IXC017DA

A2X0IXC018DB

A2X0IXC075DA

Protective tape

A00JIXC018DA

A00JIXC224DA

E-9

3. Insert the toner cartridge into the machine.

Note:

Make sure that the color is same between insert-

ing port and the toner cartridge.

4. Push the toner cartridge all the way in.

Note:

Make sure that the toner cartridge is pushed all the

way in.

5. Using the same procedure, install the toner car-

tridges for other colors of toner.

6. Close the upper front door.

IX. Mounting the accessory parts

1. Attach the supplied caps A and B.

2. Install the supplied scanner cover. (One supplied

mounting screw)

3. Attach the supplied connector cover.

A2X0IXC060DA

A2X0IXC061DA

A2X0IXC019DA

A2X0IXC020DA

A2X0IXC021DA

E-10

4. Remove the protective cover from the supplied

stylus pen.

Note:

Discard the removed protective cover.

5. Set the stylus pen in the place shown in the illus-

tration.

X. Connecting the power cord

1. Connect the power cord.

Note:

This step may not be performed depending on the

applicable marketing area.

2. Plug the power cord into the power outlet.

3. To remove moisture from the paper in the tray,

turn ON the switch shown in the illustration.

Note:

This step may not be performed depending on the

applicable marketing area.

XI. Toner supply

Turn ON the Main Power Switch.

Note:

• Toner is automatically supplied in parallel with

warm-up.

• If any one of the toner cartridges is not set,

toner supply does not start.

A2X0IXC068DA

A2X0IXC023DA

A0P0IXE075DA

C4004U139CA

A0P0IXE076DA

Switch

Andere Handbücher für bizhub C754e

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta bizhub C200 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 500 Bedienungsanleitung

Konica Minolta

Konica Minolta Bizhub C3350 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 42 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 163 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 363 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C360 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 601 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4690MF Bedienungsanleitung

Konica Minolta

Konica Minolta FK-502 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 223 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 36 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 361 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C754 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C450 Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1390 MF Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB C300 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub PRO C6501/C6501P Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 223 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C203 Series Beilage

Konica Minolta

Konica Minolta magicolor 2300 Series Bedienungsanleitung

Konica Minolta

Konica Minolta Bizhub 362 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 223 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 215 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta bizhub C754e Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken