Konica Minolta KIP 700m Bedienungsanleitung

MULTI-FUNCTION PRINTER

KIP 700m

Hardware Operation Guide

Version A.3 September 6, 2010

Carefully read this manual before use.

Keep this manual for future reference.

(1)

Thank you for purchasing the Multi-Function Printer KIP 700m.

This Hardware Operation Guide contains functional and operational explanations for the KIP 700m.

Please read this Hardware Operation Guide carefully before using the printer.

Please keep this Hardware Operation Guide for future reference.

1. When this product is installed in North America.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

2. When this product is installed in Europe

This equipment complies with the requirements in Pub.22 of CISPR Rules for a Class B

computing device.

Operation of this equipment in a residential area may cause unacceptable interference to radio

and TV reception requiring the operator to take whatever steps are necessary to correct the

interference.

Do not install Machine around other electronic equipment or other precision instruments.

Other devices may be effected by electrical noise during operation.

If the Machine is installed near other electronic equipment, such as a TV or a radio,

interference to said equipment, such as noise or flickering, may occur.

Use a separate power line and install the PRINTER as far as possible from said equipment.

The International ENERGY STAR ® Office Equipment Program is an international program that

promotes energy saving through the penetration of energy efficient computers and other office

equipment. The program backs the development and dissemination of products with functions that

effectively reduce energy consumption. It is an open system in which business proprietors can

participate voluntarily. The targeted products are office equipment such as computers, monitors,

printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are

uniform among participating nations.

The symbol shown indicates that this product conforms to Directive

2002/96/EC of the European Parliament and the council of 27 January

2003 on waste electrical and electronic equipment (WEEE) and does not

apply to countries outside of EU.

KIP 700m is an ENERGY STAR qualified multifunction device.

The symbol shown indicates that this product conforms to

SJ/T11364-2006 of People’s Republic of China Electronic

Industry Standard and does not apply to countries outside of

People’s Republic of China.

The symbol shown indicates that this product conforms to GB

18455-2001 11364-2006 of National Standard of the People’s

Republic of China and does not apply to countries outside of

People’s Republic of China.

Chapter 1 Before Use1-2

1. 1 Installation Requirements

The following conditions are required for installation of the equipment.

1. POWER SOURCE should be rated as follows.

In U.S.A. : 120V plus/minus 10%, 50/60Hz, 15A or higher

In Europe : 220-240V plus 6% or minus10%, 50/60Hz, 10A or higher

2. The equipment must be on an exclusive circuit.

3. The outlet must be near the equipment and easily accessible.

I Norge: Kan kobles til IT strøm distribusjonssystemer.

1. Make sure to connect this equipment to a grounded outlet.

2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near

the equipment and shall be easily accessible.

The site temperature range = 10 to 32 degrees Centigrade, with the humidity between

15% to 85% RH. (NON CONDENSING)

Keep the printer away from water sources, boilers, humidifiers or refrigerators.

1. The installation site must not have open flames, dust or ammonia gases.

2. The equipment must not be exposed to the air vents from air conditioners.

It may affect the image quality.

3. The equipment should not be exposed to the direct sunlight.

Please draw curtains to block any sunlight.

When you open the Movable Unit, do not expose the Photoconductive Drum

to strong (intense) light as this will damage the Drum.

Ozone will be generated while this equipment is use, although the quantity generated

is within safe levels. (see certifications)

Ventilate the room, if required.

Keep ample room around the equipment to ensure comfortable operation.

(Refer to the following figure.)

The equipment must be leveled and the floor strength must be ample to sustain the

weight of the equipment.

KIP 700m

10cm/4” or larger

(Front)

(Rear)

20cm/8” or larger with no option

10cm/4” or larger

20cm/8” or larger

Chapter 1 Before Use1-5

1. 4 Specifications

1. 4. 1 General

Subject Specification

Model KIP 700m

Configuration Console

Power consumption

(Maximum)

1500w (US model)

1600w (Europe/Asia model)

(Including Scanner & Controller Unit)

Power consumption

(Low power mode)

13w or less (US model)

13.5w or less (Europe/Asia model)

Acoustic noise Idling Max. 51db

Printing Max. 60db

(impulse sound excluded) EN ISO 7779

Ozone Max. 0.05ppm (Measurement method under UL Standard)

Dimensions 1245mm (Width) x 833mm (Depth) x 1174mm (Height)

(including Stand)

Weight About 144kg / 318lbs (Stand excluded)

Environmental condition

for usage

Temperature: 10 to 32 degrees Centigrade / 50 to 89.6 F

Humidity: 15 to 85% RH

Interface Network Interface (10 BASE-T / 100 BASE-TX / 1000 BASE-T)

Rating input power In the US : 120V plus/minus 10%, 50/60Hz, 12A

In Europe : 220-240V plus 6% or minus 10%, 50/60Hz, 6.5A

NOTE

The above specifications are subject to change without notice.

Chapter 1 Before Use1-6

1. 4. 2 Printer part

Subject Specification

Printing method LED Array Electro photography

Photoreceptor Organic Photoconductive Drum

Print speed 40mm per second

(Inch) 1.7ppm/E 2.9ppm/D Landscape

(Metric) 1.6ppm/A0 2.8ppm/A1 Landscape

Print head LED Array

Resolution of print head 600dpi x 600dpi

Print width Maximum 914mm / 36”

Minimum 297mm / 11” for roll media

210mm / 8.5” for cut sheet

Print length Maximum

(Standard) 2,400mm for A0 / 36” wide (plain paper / bond)

or “2 x Standard length” (plain paper / bond)

“1 x Standard length” (plain paper / bond, 2” core roll)

“1 x Standard length” (vellum / tracing paper, film)

(Option) 3,600mm

Minimum 297mm / 11”

Print size

(from Paper Tray, option)

ISO (mm)

Width

Length

ANSI (inch)

Width

Length

Warm up time Shorter than 2 minutes 30 seconds

At 23oC, 60%RH, the rated voltage, plain paper

First print time 42 seconds (D Landscape), 41 seconds (A1 Landscape)

At 23oC, 60%RH, the rated voltage, plain paper

(after submission of the concerning plot data)

Fusing method Heat and Pressure Rollers

Development method Dry type non-magnetic mono-component toner

NOTE

The above specifications are subject to change without notice.

NOTE

If the print is longer than 2,400mm, its image quality or the

reliability of paper feeding is not guaranteed.

420 297 210

594 X

420 X

297 X X

18 17 12 11 9 8.5

24 X

22 X

18 X

17 X

12 X X

11 X X

Chapter 1 Before Use1-7

Subject Specification

Media source 1 Roll Deck (3” / 2” core roll)

Manual Feeder (single cut sheet)

Paper Tray (multiple cut sheet, option)

Media (Recommended Roll Media)

- US model:

Bond : 64g/m2to 80g/m2, US Bond (20# Bond)

Vellum : US Vellum (20# Vellum)

Film : 4MIL (4Mil-2 Xero Film)

- Europe/Asia model:

Plain Paper : 64g/m2to 80g/m2,

Oce Red Label Paper(75g/m2)

Tracing Paper : Oce Transparent Paper (80g/m2)

Film : Oce Polyester Film

- 2” roll core : HP Universal Bond Paper

(Cut sheet)

Plain Paper / Bond

Storage of consumables (Toner cartridge)

Store the cartridge within the temperature range from 0 to

40 degrees Centigrade and within the humidity range from 10

to 85% RH.

NOTE

The above specifications are subject to change without notice.

Chapter 1 Before Use1-8

1. 4. 3 Scanner part

Subject Specification

Scanning method Contact Image Sensor (CIS)

(5 pieces of A4 sized CIS)

Light source LED (R/G/B)

Setting of original Face up

Starting point of scan Center

Scan width Max: 914.4mm / 36”

Min : 279.4mm

Scan length Max: 6,000mm / 19.7ft (Including the margin area)

Min : 210mm / 8.5” (Including the margin area)

Margin area 3mm from leading, trailing and both side edges

Optical resolution 600dpi

Digital resolution 200 / 300 / 400 / 600 dpi

Original transportation Sheet through type

Transportable original

thickness

Max: 1.60mm

Min : 0.05mm

Scanning speed 60mm per second (mono 600dpi max)

NOTE

The above specifications are subject to change without notice.

NOTE

If the original is thicker than 0.65mm, its image quality is not

guaranteed.

Chapter 2 Basic Operation2-2

2. 1 Turning on KIP 700m

1. Ensure that the KIP 700m is plugged into a dedicated wall outlet.

2. Press “ | ” side the Power Switch on the right side of the printer to turn on the KIP 700m.

PowerSwitch Press“|“side.

WARNING

(1) Do not handle the Power Plug with wet hands, or you may receive an electrical shock.

(2) Make sure to earth the machine for safety.

(3) Do not plug the printer into a multi-wiring connector in which other devices are plugged.

It may overheat the outlet and may result in a fire.

(4) The OUTLET must satisfy the following conditions.

In the U.S.A. : 120V plus/minus 10%, 50/60Hz and 15A

In Europe : 220-240V plus 6% or minus 10%, 50/60Hz and 10A

Chapter 2 Basic Operation2-3

3. The User Interface (UI) starts operating, and displays the following Copy Mode Screen in one

minute.

The Ready Indicator on Copy Mode Screen will flash during warming up.

The UI screen may vary depending on your system configuration.

(Shown with available options)

4. When Ready Indicator stops flashing, the KIP 700m is ready for operation.

NOTE

It is impossible to make any prints while Ready Indicator is

flashing in orange. Please wait until it turns in green.

Ready Indicator

Chapter 2 Basic Operation2-4

2. 2 Turning off KIP 700m

1. There is a Power Switch on the right side of KIP 700m.

Press its “ ” side to turn off the KIP 700m.

Power Switch Press “ ” side.

CAUTION

The KIP 700m print engine and UI appear to be shut down when you turn off KIP 700m.

However, the controller PC embedded inside the KIP 700m is still operating and will

shutdown in approximately two minutes after Power Switch operation.

Do not unplug the KIP 700m before the controller PC completes its shutdown. Doing so

may damage data or the device.

Inhaltsverzeichnis

Andere Konica Minolta Multifunktionsdrucker Handbücher

Konica Minolta

Konica Minolta BIZHUB C300 Bedienungsanleitung

Konica Minolta

Konica Minolta 7033 Bedienungsanleitung

Konica Minolta

Konica Minolta 7255 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 4750 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 4650EN Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 501 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 160 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 4690MF Originalbetriebsanleitung

Konica Minolta

Konica Minolta Magicolor 2490 MF Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C3100P Bedienungsanleitung

Konica Minolta

Konica Minolta 7020 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub c3110 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 600 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C450 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C353 Series Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C452 Series Service-Handbuch

Konica Minolta

Konica Minolta bizhub C650 Series Bedienungsanleitung

Konica Minolta

Konica Minolta Drypro 832 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 754e Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C450 Bedienungsanleitung

Konica Minolta

Konica Minolta A0HF012 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C452 Series Leitfaden

Konica Minolta

Konica Minolta bizhub 223 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 1690MF Montageanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung