Konica Minolta Bizhub PRO 950 Series Bedienungsanleitung

E-1 A0Y5961111

INSTALLATION MANUAL

950

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

I. Installation space (Unit: mm)

Machine weight: Approx. 285 kg

II. Confirmation prior to installation

1. Select a flat and stable place that can sustain the

machine’s weight.

2. Confirm that the voltage and the frequency meet

the product specifications, and that the current

capacity of the outlet meets or exceeds the

capacity specified.

3. Connect the machine directly to a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with a wet

or dirty hand. (May cause an electrical shock.)

5. Do not install the machine in a place with high

temperatures or high humidity, or in direct sun-

light.

6. Do not install the machine in a dusty place, and/

or near volatile flammable substances.

7. Do not install the machine in a poorly ventilated

place.

III.

How to bring down the machine onto the floor

1. Using the spacers and the spanner, lower the

adjuster feet and remove the cushions.

2. Raise the adjust feet again, to let the machine

descend onto the pallet. In this case, be sure to

extremely raise the adjuster feet.

* Be sure to work on the above procedure in succession,

respectively for the right side and left side of the machine.

3. Fix the veneer with its beveled portion turned

upward, to the right end face of the pallet by two

nails as illustrated below.

4. Set the 2 cushions removed from the machine,

below the veneer as illustrated below.

980 295675

150 116

435

2066

1603

2366

1420

690

990

1203

183

150

410 840

A0Y5IXC038CA

1930

780

950 200

A0Y5IXC039CA

A0Y5IXC033CA

Spanner

Spacers

57AEIXE044SA

Corrugated fiberboard Nail: 2 pcs.

Veneer

57GEIXE043SA

Cushions

Corrugated fiberboard

Veneer

Cushions

Applied Machine:

950

E-2

5. Let two persons gently bring down the machine

onto the floor with the right side coming first.

* Do not hold the arm in the step 5.

Note 1: Precautions for moving the main body

Note 2:

IV. Accessory parts

Note:

For the usage of the following accesaries, refer to

the service manual.

V. Installation procedures

Note:

Do not plug in the power cord until you are instructed

to do so.

1. Remove the wrapping sheet from the ADF.

2. Inspect the outside of the Main body and confirm

that there is no damage.

3. Remove the locking tapes on the exterior panels.

Note:

Locking guide tapes indicate the portions to be

unlocked; those tapes should be removed after the

completion of each unlocking procedure.

Confirm that the Adjuster feet are fully wound up

before moving the machine.

The hard disk unit built into the Main body is vul-

nerable to vibration and impact, so always remove

it before moving the Main body.

No. Name Q’ty

1. Spacers 4

2. User’s guide holder 1

3. Ventilation duct 1

4. Developer 1

5. Cotton swabs 1

6. Installation manual 1

User’s guide (Except for Europe)

8. Nails 2

9. Veneer 1

10. Truss screw M4x6 (Black) 6

11. TP screw M4x6 4

12. CD-ROM 1 set

13. Sub power label 1

14. Power cord instruction

(for some areas only) 1

15. Operation panel 1

16. Sticker 1

17. Arm cover /4 1

18. Panel cover 1

19. Quick guide 1

No. Name Q’ty

20. Weight 4

21. TP screw M3x8 2

A0Y5IXC034CA

A0Y5IXC001CA

Front

door

Front left

door

Locking

guide tapes

Wrapping sheet

Protection

materials

Protection

material

E-3

4. Open the ADF, and remove the original glass pro-

tecting cushion and the original glass protecting

paper.

5. Remove the Red paper on the left side of the Main

body, and remove the Optics unit locking screw.

6. Remove the locking tapes within the Trays.

(1) Open the Front door and Front left door. Pull

out the Tray 1 while pressing the Lock lever

mounted on the left side of the tray.

(2) Remove the locking tapes first and then at the

end locking guide tape of the Tray 1.

(3) Repeat procedures (1) and (2) to remove the

locking tapes of the Tray 2 and the Tray 3.

7. Release the Duplex unit lock.

(1) Pull out the Tray 1.

(2) Remove the Duplex unit lock screws. (Arrow

)

(3) Slide the Duplex unit lock piece. (Arrow )

(4) Turn the Duplex unit lock piece to remove it.

(Arrow )

(5) Return the Tray 1 to its original position.

(6) Remove the 3 Duplex unit lock screws (right

side: 1 pc. left side: 2 pcs.), then remove the 2

Duplex unit lock pieces. (Arrows & )

A0Y5IXC002CA

Original glass protecting paper

Original glass protecting cushion

A0Y5IXC003CAA0Y5IXC003CA

Red paper

A0Y5IXC004CA

Lock lever

A0Y5IXC005CA

Locking guide tape

Locking tapes

A0Y5IXC006CA

Lock pieces

Screws

Screw

Protection paper

Locking guide tape

Protection

material

E-4

(7) Remove the Protection paper and the Protec-

tion material from the Toner supply unit.

Note:

Also make sure to remove the thick paper from the

movable part of Toner supply unit.

(8) Insert a finger under the Duplex unit, and while

pushing the Duplex unit lock to the left to

release it, turn the Duplex unit release lever to

the right. (Arrows & )

(9) Pull out the Duplex unit while holding the

Duplex unit cushion. (Arrows & )

Note:

When pulling out the Duplex unit, be sure that all

the trays of the Main body are returned in place.

(10) Peel off the locking tapes, then remove the

Duplex unit cushion.

(11) Turn the reverse unit and the jam recovery

lever to the left, and loosen the 2 screws on

the Fusing unit cover, remove the cover.

(12) Check the position of the end of the fusing roller

pressure spring. If it is not in the appropriate

position, turn the springs on both sides of the

fusing unit so that the ends of the springs are

2mm-4mm from the edge of the pressure plate.

Note:

If the springs are not in the appropriate position,

there may be insufficient fusing when thick paper

is used.

(13) Remove the locking guide tape on the Pressure

release shaft, and then insert a screwdriver into

the hole in the Pressure release shaft and turn it

counterclockwise until it hits the end.

(14) Secure the Fusing unit cover, and return the

Jam recovery lever and the Reverse unit to

their original positions.

(15) Reinstall the Duplex unit to the Main body, and

turn the Release lever to the locking position.

A0Y5IXC035CA

Cushion

Protection

paper

Protection

material

A0Y5IXC008CA

Reverse unit

Fusing unit cover

Jam recovery

lever

A0Y5IXC009CA

End of spring

Pressure plate

2mm-4mm

A0Y5IXC010CA

Pressure release

shaft

Locking guide tape

E-5

8. Install the Control panel.

(1) Install the operation panel as the following picture.

(TP screw M4x6: 4 pcs.)

(2) Insert the connectors. (2 connectors)

Note:

Arm length can be changed upon customer

request. The position of the Control panel can be

adjusted forward or backward.

Default setting at installation: Arm is positioned

forward.

If the change is not necessary, move to step (3) on

page E-6.

Procedures to change Control panel arm length

Step

1. Remove the adjusting knob. (Bind screw

M4x8: 2 pcs.)

A0Y5IXC011CA

TP screws M4x6

A0Y5IXC012CA

Connectors

A0Y5IXC013CA

Bind screws

M4x8

Adjusting knob

2. Remove the arm cover /1 and /2. (Truss screw

M4x6: 4 pcs.)

3. Remove the arm cover /3. (2 screws)

4. Shorten the Control panel arm and fix it.

(top surface: 4 pcs., bottom surface: 2 pcs.)

A0Y5IXC014CA

Arm cover /1 Arm cover /2

Truss screws M4x6 Truss screws M4x6

A0Y5IXC015CA

Arm cover /3

Arm fixing screws

E-6

(3) Install the panel cover. (Truss screw M4x6

(Black): 2 pcs.)

(4) Install the arm cover /4. (Truss screws M4x6

(Black): 2 pcs. )

(5) Place a sticker on the top of the arm cover /1 and /2.

9. Plug in the Power cord and turn the Main power

switch ON, and close the Front left door and

Front door.

10.Turn the Sub power switch ON, after the comple-

tion of the electrode cleaning process (this pro-

cess is executed automatically and takes about 1

minute), turn the Sub power switch OFF.

Note:

• The Cleaning blade is preset to the invalid posi-

tion at the factory. The ON/OFF operation of the

Sub power switch initializes that position and

places the Cleaning blade at the valid position.

• Do not omit this ON/OFF operation, as another

reason is that the automatic electrode cleaning

operation is executed simultaneously.

• The Photo conductor will start turning about 30

seconds after the electrode is cleaned, so turn

the Sub power switch OFF before that occurs.

11. Open the Front door and Front left door, and turn

the Main power switch OFF.

5. ADF can not be opened depending on the

position of the Control panel.

It can be avoided by the following steps.

• Install the screws at the positon shown in

the following picture. (Truss screw M4x6:

1 pc. included in the package)

6. The cover of LU-408 may contact with the

Control panel depending on the position of the

panel.

It can be avoided by the following steps.

• Install the screw at the positon shown in

the following picture. (Truss screw M4x6:

1 pc. included in the package)

7. Reinstall the arm cover /3. (2 screws)

8. Reinstall the arm cover /1 and /2. (2 screws

each)

9. Reinstall the adjusting knob. (2 screws)

A0Y5IXC036CA

Truss screw M4x6

A0Y5IXC037CA

Truss screw M4x6

A0Y5IXC017CA

Panel cover

Truss screw M4x6 (Black)

A0Y5IXC029CA

Truss screw M4x6 (Black)

Arm cover /4

A0Y5IXC030CA

Sticker

A0Y5IXC018CA

Main power switch

E-7

12. Apply the setting powder on the Photo conduc-

tor.

(1) Remove the 2 screws (A) and loosen the

screw (B) securing the Toner supply unit. Then

pull out the Slide hinge of the Toner supply unit

and open the Toner supply unit for 180

degrees.

(2) Loosen 3 screws on the Photo conductor unit

cover and remove the cover.

(3) Turn the Release lever to the right, and remove

the 2 screws (A) on the Photo conductor unit

and the screw (B) on the Coupling. Use a

screwdriver to turn the Coupling (Photo con-

ductor) in the direction of the arrow for one

rotation. Hold the Photo conductor unit with

both hands as shown in the figure to pull it out.

Note1:

• Turning the Photo conductor for one rotation

prevents toner from spilling.

Note2:

• Place your left hand on the circle engravings on

the Photo conductor unit.

• When pulling out the Photo conductor unit,

make sure that the Duplex unit is inserted in the

Main body.

(4) Remove the screw fixing the Developer suction

box. Then pull the box out, tilting it at an angle.

A0Y5IXC019CA

Screw (B)

Screw (A)

Slide hinge

A0Y5IXC020CA

Screws

Photo conductor unit cover

57GEIXE015SA

Screws (A)

Screw (B)

Engravings

57GAIXC016SA

E-8

(5) Release the Developing unit pressure lever as

shown in the figure.

(6) Hold both ends of the Developing unit and

remove it carefully from the Photo conductor

unit.

(7) Pull up the claws of the upper cover to remove

the cover.

Note:

Do not work in a dusty place (to prevent foreign

objects from getting into the unit).

(8) Add developer evenly from the top of the Agita-

tor screw along its entire length. (Add both of 2

bags of developer.)

(9) Rotate the Developing gear counterclockwise

to coat the Developer around the Developing

roller completely.

Note:

Do not rotate the Developing gear clockwise.

(10) Reinstall the Developing unit cover.

Note:

Make sure that both the bosses of the upper cover

are put into the slots on the Developing unit. [See

the Illustration of step (7)]

(11) Disconnect the 2 clamps fastening the wiring

of the Charging corona unit.

(12) Disconnect the connector (1 pc.) from the

Charging corona unit, and remove the Charg-

ing corona unit by holding both grips.

Note:

The Charging corona unit must be face up when it

is placed.

57GAIXC017SA

A0Y5IXC021CA

Claws

Boss

Stopper roller

57GAIXC019SA

57GEIXE020SA

Developing roller

A0Y5IXC028CA

Clamps

Connector

E-9

(13) Disconnect the connector and the clamp from

the Stay, and release the Cleaning unit by

turning the Cleaning unit lock levers in the

direction of the arrow. Hold both ends of the

Cleaning unit, and pull it out along the shape

of the bottom bracket of the Photo conductor

unit.

(14) Disconnect the 3 connectors from the Stay,

and remove the wiring from the clamp, and

loosen the 2 screws of the Stay, and remove

the Stay.

Note:

Be sure to disconnect the connectors first, then

loosen the screws of the Stay.

(15) Loosen the screw (A) and remove the screw

(B) of the Sensor cover. Then move one end

of the Sensor cover away from the Photo con-

ductor.

(16) Pull the Photo conductor straight up.

(17) Apply the setting powder on the surface of the

Photo conductor by a whole round.

57GEIXE022SA

Clamp

Connector

Cleaning unit

lock levers

57GEIXE023SA

Screw

Stay

57GEIXE024SA

Screw (A)

Screw (B)

Sensor cover

57GAIXC025SA

57GEIXE045SA

Setting powder

E-10

(18) Clean the surfaces of the IDC sensor and the

JAM detection sensor with alcohol and a cot-

ton swab.

Note:

Never rub with a dry cloth.

(19) Hold both ends of the Photo conductor, and

move it straight down to set it in the Photo

conductor unit.

Note:

Do not put the Photo conductor on the rib of the

Photo conductor unit.

(20) Reinstall the Sensor cover and secure it with

screws.

Note:

Be sure to secure the Sensor cover so as to contact

the stopper bosses on the Photo conductor unit.

(21) Reinstall the Stay, connect the connector (3

pcs.), and fasten the wire bundle of connector

where it located in front of the Photo conduc-

tor unit, on the clamp.

Note:

When connecting the connector of the wiring

linked to the Charging corona unit, be sure that the

Wiring band to be used as a mark should be posi-

tioned inside the Edge saddle (to the Photo con-

ductor side).

(22) Set the 1st Cleaning blade.

Note:

The 2nd Cleaning blade is charged at the factory.

Push up the Blade unlock arm in the direc-

tion of the arrow until it stops.

Rotate the Blade charge lever fully in the

direction of the arrow.

Note:

Hold the Blade unlock arm pushed up.

Release the Blade unlock arm.

Note:

Hold the Blade charge lever at the fully rotated

position.

Release the Blade charge lever.

A0Y5IXC031CA

Sensors

57GEIXE027SA

Rib

A0Y5IXC022CA

Wiring band

(used as a mark)

Edge saddle

57GEIXE028SA

Blade unlock arm

Blade charge lever

Andere Handbücher für bizhub PRO 950 Series

Inhaltsverzeichnis

Andere Konica Minolta Drucker Handbücher

Konica Minolta

Konica Minolta PagePro 1350W Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5550 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 3300P Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C200 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C4000i Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub PRO C65hc Installationshandbuch

Konica Minolta

Konica Minolta Magicolor 5550 Bedienungsanleitung

Konica Minolta

Konica Minolta DRYPRO SIGMA Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 8650 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 1600W Originalbetriebsanleitung

Konica Minolta

Konica Minolta magicolor 1600W Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 4050 Bedienungsanleitung

Konica Minolta

Konica Minolta PAGEPRO 5650EN Bedienungsanleitung

Konica Minolta

Konica Minolta 2060 Kurzanleitung

Konica Minolta

Konica Minolta Printer Copier Bedienungsanleitung

Konica Minolta

Konica Minolta DRYPRO Model 793 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 2200 DeskLaser Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5440 dl Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5450 Bedienungsanleitung

Konica Minolta

Konica Minolta 8050 Bedienungsanleitung

Konica Minolta

Konica Minolta AccurioPress C2070 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub PRESS 1250/1250P Bedienungsanleitung

Konica Minolta

Konica Minolta CF2002 Handbuch

Konica Minolta

Konica Minolta PagePro 1300W Konfigurationshandbuch

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

Konica Minolta bizhub PRO 950 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken