Konica Minolta AU-102 Bedienungsanleitung

E-1

AU-102 Authentication Unit

INSTALLATION MANUAL

A79J-9621-00

Applied Machines: C658/C558/C458

COLOR MFP: 65 ppm/55 ppm/45 ppm

Product Code: A79J/A79K/A79M

1. Accessory parts

Note:

• The Working Table WT-506 needs to be

mounted before to install this unit.

• This manual provides the illustrations of the

accessory parts and machine that may be

slightly different in shape from yours. In that

case, instead of the illustrations, use the

appearance of your machine to follow the

installation procedure. This does not cause any

significant change or problem with the proce-

dure.

• If none of the later steps instruct you to use the

parts including screw and cover that you

removed following the instructions described in

this manual, discard them.

No. Name Shape Q’ty

1. Authentication

unit

2. USB cable

3. Hook-and-loop

fastener A

(hook)

(20 x 10 mm) 2

4. Hook-and-loop

fastener B

(loop)

(20 x 10 mm) 2

5. Hook-and-loop

fastener C

(hook)

(25 x 18 mm)

6. Hook-and-loop

fastener D

(loop)

(25 x 18 mm)

7. Finger placement

seal

8. CD-ROM

9. Safety

information

guide 1

set

10. Installation

manual

set

No. Name Shape Q’ty

Keep this bag away from babies and

children. Do not use in cribs, beds,

carriages, or playpens.

The thin film may cling to nose and

mouth and prevent breathing. This bag is

not a toy.

E-2

2. Installation procedures

(1) Turn OFF the power switch and unplug the

power cord from the power outlet.

(2) Affix the supplied finger placement seal at the

location shown below on the working table.

(3) Remove the cap from the working table (one

place).

(4) Fix the authentication unit on the working table

using the supplied hook-and-loop fasteners (A,

B, C and D).

A: two places on the underside of the authentica-

tion unit

B: two places on the working table

C: one place on the underside of the authentica-

tion unit

D: one place on the working table

(5) Run the supplied USB cable through the hole

from under the table and connect the cable to the

authentication unit.

(6) Open the cover shown in the illustration on the

right side of the machine.

(7) Remove the indicated knockout from the top of

the cover using nippers.

Knockout

E-3

(8) Connect the USB cable to the machine.

Note:

Connect it the port shown in the illustration.

(9) Attach the cord clamp supplied with the main

body at the position shown in the illustration.

(10) Route the USB cable as shown in the illustra-

tion. Pull the USB cable up in order to remove

slack.

(11) Run the USB cable through the indicated hole

on the cover.

Rib

Cord clamp

E-4

(12) Close the cover that you opened in step (6).

(13) Route the USB cable as shown in the illustra-

tion. Run the USB cable through the four wire

saddles.

Note:

Arrange the cable so that it does not interfere with

opening or closing of the right door.

3. Configuration procedures

Install the AU-102 loadable driver (BIO_LDR.tar) to

the main unit.

(1) Prepare a USB memory where only the loadable

device driver is stored in the ROOT directory.

(Please do not save any other data in the USB

memory.)

(2) Connect the USB memory to the USB port of the

main unit.

(3) Plug the power cord into the power outlet and

turn ON the power switch.

(4) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(5) Touch “System 2” →→“Driver Install.”

(6) Touch “Loadable Driver” and touch “Start” to

install the data.

(7) Check that the data are normally installed from

the message that appears on the control panel.

(8) Turn OFF the power switch.

(9) Remove the USB memory.

(10) Turn ON the power switch.

Note:

When displayed the Service Mode screen, be sure

to turn off the power after exiting the Service Mode

screen and wait for 10 seconds or more before

turning on.

(1) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(2) Display the Billing Setting screen.

(To display the Billing Setting screen, press Stop

→ 9 on the Control Panel.)

(3) Touch “Authentication Device2.”

(4) Touch “Authentication Device2.”

(5) Touch “Body.”

(6) Touch “END.”

(7) Turn OFF and ON the power switch.

Note:

When displayed the Service Mode screen, be sure

to turn off the power after exiting the Service Mode

screen and wait for 10 seconds or more before

turning on.

Andere Konica Minolta Sicherheitssensor Handbücher

Konica Minolta

Konica Minolta AeroDR System Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Solinst

Solinst 301 Bedienungsanleitung