Koolbreeze P12HCP Climateasy 12 Bedienungsanleitung

Page 1

Climateasy 12

Portable Air Conditioner

3.5kW (12000 BTU/hour)

Model Number P12HCP

Air Conditioning

Heating

Cooling

Dehumidifying

Remote control

3 Fan speeds

LED display panel

24 Hour timer

Page 2

IMPORTANT

Installer and Users please note:

These instructions should be read carefully and left with the

user of the product for future reference.

BEFORE USE

Inspect the product including its cable and plug for any signs

of damage. If the product is damaged, DO NOT use it, and

contact your supplier immediately. The appliance contains a

refrigerant gas, so must be kept upright at all times. After

unpacking wait 3 hours for the refrigerant gas to stabilise

before use.

INSTALLATION

Stand the CLIMATEASY 12 on a firm, flat, level surface.

Connect the exhaust hose as follows: expand a small section

of the end, and screw into the indoor adaptor; then slide the

indoor adaptor into the slot at the back of the unit. Expand a

small section of the other end of the hose, and screw into the

fish-tail-shaped adaptor.

Page 3

Slide the two-part window adaptor to the correct length to fit

the window. Close the window as far as possible to keep the

window adaptor in place. Clip the fish-tail shaped adaptor into

the aperture in the window adaptor.

Keep the hose as straight as possible, avoid dips where the

moisture from the exhaust air can condense and fill the tube

with water. Do not allow the hose to be crushed.

Correct Mounting Correct bend of Exhaust

Incorrect Bending of the Exhaust can cause malfunction

Page 4

The hose can be expanded up to 1.8 m long, but the shorter it

is the more efficiently the CLIMATEASY 12 will operate. Do

not extend the hose, or replace with another type of hose.

Remote Control

Fit one lithium 3V battery to the remote control, observing the

correct polarity.

Use only lithium 3V batteries.

Remove the battery if the remote control is not used for a

month or longer.

Do not attempt to recharge the supplied batteries.

Do not dispose of the batteries in a fire as they may explode.

GENERAL SAFETY REQUIREMENTS

Domestic wiring must be tested periodically by a qualified

electrician at least once every 10 years or at every change of

occupancy.

For office and retail premises, and buildings such as village

halls, the wiring must be inspected at least once every 5 years.

It is recommended that all building be fitted with smoke alarms

(it is mandatory for new buildings).

Page 5

PRODUCT SAFETY

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of

the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance

Place the appliance on a firm flat surface. Ensure that the it

is kept upright at all times

Ensure that there is at least 300mm (1') between the sides

of the appliance and any flammable materials

Ensure that there is at least 900mm (3') from the top of the

appliance and any flammable materials.

Do not place on soft surfaces.

Do not cover.

Do not obstruct the air intakes and exhausts.

For indoor use only

Not suitable for use in boats, caravans or similar locations.

Do not use in bathrooms, or in wet locations.

Do not place the mains lead beneath a carpet or rug.

Do not use the appliance in locations where paint, petrol or

other flammable liquids are used or stored.

Always transport and store in an upright position.

Do not allow the appliance to fall over when there is water

in the bucket.

PAT TESTING.

When used in an office environment, this product must be

safety-tested yearly by a qualified electrician (PAT Tested) in

order to comply with the Electricity at Work Regulations.

We recommend that it is PAT tested regularly when used in a

domestic environment.

Page 6

CONTROLS

REMOTE

DISPLAY PANEL

Page 7

OPERATION

Leave the appliance in an upright position for 3 hours before

first use.

Plug the mains lead into a 13 Amp mains socket (unless

permanently installed)

If connecting via an extension lead, make sure that the lead is

rated at 13 Amps or more, and that it is fully unwound. Switch

the unit on at the mains socket.

ON/OFF Button: Press the "ON/OFF" button to start the unit.

The Power indicator illuminates when the appliance is ON.

There will be a short delay (of about a minute) before the

appliance starts to operate.

"MODE" Button: Select the mode by pressing the "MODE"

button. The available modes are:

Automatic mode: either heats or cools as required to

maintain the selected room temperature. Then use the TEMP+

and TEMP- buttons to select the desired room temperature.

When the temperature reaches the desired temperature, the

compressor will stop, and the fan will continue to run.

Cooling mode: cools if the room temperature is above the

selected temperature.Then use the TEMP+ and TEMP-

buttons to select the desired room temperature. When the

temperature reaches the desired temperature, the compressor

will stop, and the fan will continue to run.

Dehumidifying mode: removes humidity, but does not effect

room temperature. The fan operates at its lowest speed. For

best results, do not use the exhaust tube, but fit a permanent

drainage pipe to the drain outlet as shown on page 9.

Fan mode: circulates the air, but does not affect room

temperature or humidity.

Page 8

Heating mode: heats if the room is temperature is

below the selected temperature. Then use the TEMP+

and TEMP- buttons to select the desired room temperature.

When the temperature reaches the desired temperature, the

compressor will stop, and the fan will continue to run. Heating

performance reduces if the outdoor temperature falls below

°C

"SPEED" Button: Set the fan speed using the fan speed

control.

In all modes except dehumidifying mode. The fan speed can

be low, medium or high. The fan speed is indicated by the

speed of the segments on the windmill symbol on the LED

display.

TEMP+ and TEMP- buttons:

Use the + and - buttons to select the desired room

temperature. The temperature can be set to any temperature

from 16 °C to 31 °C. Selecting a lower temperature whilst

heating, or a higher temperature whilst cooling will reduce

power consumption.

SWING button: Press the "SWING" button to turn the

oscillation of the louvres on or off.

If the "WATER FULL" indicator lights, the condensate water

tank is full. This should only happen very rarely, as most of

the water collected is evaporated and sent down the exhaust

air tube.

To empty the water, switch the unit off by pressing the

ON/OFF button, wait for three minutes, and then disconnect

from the mains supply. Place a drainage pan underneath the

drain outlet plug (an the bottom of the unit, at the back in the

centre). Withdraw the bung, and allow the water to drain into

the drainage pan. Replace the bung, and reconnect the unit to

the mains supply.

Page 9

The water should be disposed of down a drain.

To avoid the need to empty the water, a permanent drain tube

may be fitted as shown: use a piece of 18mm diameter tube

(not supplied) and run the pipe to a drain, making sure that it

runs downhill all the way.

Unplug the CLIMATEASY 12 from the mains when not in use.

USING THE TIMER

The timer can set the unit to run for a selected time (between 1

and 24 hours) and then turn OFF.

Or, it can set the unit to wait for a selected time (between and

24 hours) before turning ON.

To select timed turn-off press the timer button whilst the unit is

switched ON. Then adjust the time using the + and - buttons

for the number of hours' delay before switching off.

To select timed turn-on press the timer button whilst the unit is

switched OFF (connected to the mains supply but switch OFF

using the ON/OFF button). Then adjust the time using

the + and - buttons for the number of hours' delay before

switching on.

To cancel the timer, press the TIMER button again.

Page 10

USING THE REMOTE CONTROL

The heating, cooling, dehumidifying and fan modes are

selected in exactly the same way as using the control panel

on the main unit. .

Inhaltsverzeichnis

Andere Koolbreeze Klimaanlage Handbücher

Koolbreeze

Koolbreeze Kompact 18 Bedienungsanleitung

Koolbreeze

Koolbreeze Climateasy 12NG Bedienungsanleitung

Koolbreeze

Koolbreeze Climateasy 14R2 Bedienungsanleitung

Koolbreeze

Koolbreeze CLIMATEASY 14 P-14HCP Bedienungsanleitung

Koolbreeze

Koolbreeze Climateasy 12R2 Bedienungsanleitung

Koolbreeze

Koolbreeze Kompact 16 Bedienungsanleitung

Koolbreeze

Koolbreeze Wallbreeze Mk2 Gebrauchs- und Pflegehandbuch

Koolbreeze

Koolbreeze Climateasy 14 Bedienungsanleitung

Koolbreeze

Koolbreeze Climateasy 12R2 Bedienungsanleitung

Koolbreeze

Koolbreeze UNIQUE P-12000HCU Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung