Korg D16 Kurzanleitung
Korg D16 Internal Hard Disc Drive Upgrade
© amgard.net 2002 - (& v2.1 2004) page 1
Note : I accept no responsibility for any damage that may be caused by performing the following
operation. It is not an approved Korg modification and is performed entirely at your own risk.
You will need:
• #2 crosshead (Posidriv) screwdriver
16
• 11mm ( / ) socket-spanner or point-nosed pliers, to remove ‘Value Dial’ retaining nut
7"
• small jeweler’s screwdriver or hook, to remove knobs
• hand towel (or similar), to ‘cushion’ the work surface
• grounding strap, to eliminate static electricity
• small container, to keep small parts safe whilst working
Place the hand towel on the work-top, so that the top panel of the D16 is not scratched when it is inverted.
You should take normal anti-static precautions, eg. have a grounding strap connected between your wrist
and an earthed (grounded) contact.
Ensure you will not be disturbed, especially by children or pets.
When you are ready ............
Remove the input trim and the headphone level
knobs. Theyall justpull off but you may need to prise
them withasmalljeweler’sscrewdriverorsmallhook.
Korg D16 Internal Hard Disc Drive Upgrade
© amgard.net 2002 - (& v2.1 2004) page 2
The Value Dial knob is removed in the same manner as the trim knobs. Once it is removed you will see the
16
retaining nut for the Value dial encoder, this should be removed with the 11mm ( / ) socket-spanner or by
7"
careful use of point-nosed pliers.
Now turn the D16 over, being careful not to damage the finish to the top of the case, especially to the raised
display surround.
The case is held together with 5 cross-head screws, arrowed. Unscrew them and keep them safe along with
the other small parts already removed.
Korg D16 Internal Hard Disc Drive Upgrade
© amgard.net 2002 - (& v2.1 2004) page 3
Lift the bottom of the case carefully. There are two wiring looms that connect the small circuit board in the
lower half of the case to the main mother-board.
The six connectors, marked ‘B’, need to be unplugged. They can be quite tight, but need to be unplugged
gently by lifting each end of the plug in turn until it is released. Fine point-nosed pliers can be useful here to
lift the plug, but make sure you do not pull on the cables themselves.
The flexible ribbon-cable, marked ‘C’, has a different type of connector. This is released by lifting the plastic
body slightlywhich locks the ribbon in place. Once unlocked,thecablecan be pulled easilyfrom the connector.
Remove the two screws A1 and A2, noting that A2 secures a ground wire in place.
You should now be able to carefully lift the motherboard out of the top half of the case. It is attached to the
display panel by a short ribbon cable, which may be unplugged, although it is not strictly necessary to do so.
Note: The cable marked ‘X’ is not a standard Korg fitting. This wire is a result of performing the ‘Aux Send
Modification’ detailed in Brian Smith’s instructions. (The documentation can be found at
http://www.amgard.net/misc2.htm)
Korg D16 Internal Hard Disc Drive Upgrade
© amgard.net 2002 - (& v2.1 2004) page 4
On the other side of the motherboard you willfind the
four screws that hold the disc drive in place.
Remove these screws and then slide the drive out of
its connector.
The original drive in my D16 had two small pieces of
adhesive fabric wrapped at the connector end.
These form small, thin insulating shims which should
be transferred to the new drive if possible.
Re-assembly is done by careful back-tracking of the
above instructions.
There may be some grounding washers, (arrowed),
under the disc-drive, (mine had two in place). Be sure
that you do not lose them when installing the new
drive.
Do notover-tighten the screws thatholdthe disc-drive
in place as this can lead to stressing of the
motherboard.
Korg D16 Internal Hard Disc Drive Upgrade
© amgard.net 2002 - (& v2.1 2004) page 5
Install the motherboard back into the top half of the case, making sure that all of the connectors are feeding
through and around the circuit board. Refer to the photograph on page 3 for details on the connectors.
Itisworth checking thattherubber button tops (SYSTEM, RECORD, TRACK, etc) are correctly located -they
can become displaced during the process.
You may need to manouevre the motherboard
slightly, to ensure that the LEDs and buttons line up
with the top panel.
Replace allof the ‘B’ connectors, and the two screws,(A1 and A2), remembering thatA2 holds the ground wire
in place. The ribbon cable ‘C’ pushes gently, but fully, into its socket and then the lock is pushed down to
secure the ribbon. Pull gently on the ribbon to check that it is locked in place.
Replace the lower half of the case, and fix in place with the five retaining screws. Turn the D16 over and
replace the Value Dial nut and knob, and finally the input trim and headphone level knobs.
When you power-up the D16 it will ask whether you would like to Initialize the new drive - answer ‘Yes’ and
the drive is configured by the D16 in a few seconds.
Some Disc-Drives that are known to be compatible with the Korg D16 DRS
Manufacturer 40Gb 60Gb Notes
Fujitsu MHT2040AT MHT2060AT All 4200rpm models with Fluid Dynamic bearings.
40 or 60 Gb would seem to be the optimum
choice, keeping in mind the 100 song limit on the
D16.
Toshiba MK4021GAS MK6021GAS
Both Fujitsu and Toshiba have 5400rpm models available, but at the time of writing I have not had any
reports as to their compatibility with the D16.
Andere Handbücher für D16
2
Inhaltsverzeichnis
Andere Korg Aufnahmegeräte Handbücher
Korg
Korg minikaosspad2 Bedienungsanleitung
Korg
Korg padKONTROL Produktinformationsblatt
Korg
Korg Pa5X Installations- und Betriebshandbuch
Korg
Korg MR-2000S Bedienungsanleitung
Korg
Korg Toneworks AX10A Produktinformationsblatt
Korg
Korg KAOSS PAD KP3 Produktinformationsblatt
Korg
Korg KPC-1 EFG Bedienungsanleitung
Korg
Korg PA800 Bedienungsanleitung
Korg
Korg SDD-200 Bedienungsanleitung
Korg
Korg KAOSS PAD KP2 Bedienungsanleitung
Korg
Korg Pandora Stomp Bedienungsanleitung
Korg
Korg KAOSS PAD KP3 Bedienungsanleitung
Korg
Korg PX4B Produktinformationsblatt
Korg
Korg D32XD Installations- und Betriebshandbuch
Korg
Korg SDD-3000 Bedienungsanleitung
Korg
Korg SDD-1200 Bedienungsanleitung
Korg
Korg Pandora PX5D Bedienungsanleitung
Korg
Korg AmkII Bedienungsanleitung
Korg
Korg SQ-1 Bedienungsanleitung
Korg
Korg mr-2 Bedienungsanleitung
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
