Kreg Micro-Pocket Drill Guide Kit 730 Bedienungsanleitung

English 2

French 11

Spanish 21

OWNER’S MANUAL

We’re here to help.

We want you to have an exceptional project building experience.

If you have questions or need support, please get in touch.

1-800-447-8638 | [email protected]

Tell us about your experience.

Your opinion counts. And we’re always looking for ways to

improve. Share your feedback so we can keep growing and

innovating for you. www.kregtool.com/feedback

WARNING Every user must read and follow instructions and safety

precautions in this manual. Failure to do so could result in serious injury.

Save manual for future reference.

Kreg Micro-Pocket™ Drill

Guide Kit KPHA730

Safety Precautions

WARNING Before using a power tool with this product, read and follow the

tool manufacturer’s instructions and safety precautions in addition to the safety

precautions below to reduce the risk of serious injury from hazards such as re,

electric shock, or rotating drill bit.

■Always wear personal protective equipment recommended by the

manufacturer of the power tool you are using, such as eye, hearing, or

respiratory protection.

■The drill bit is sharp. Handle with care.

■Do not allow familiarity gained from frequent use of your tools to replace

safe work practices. A moment of carelessness is sufcient to cause

serious injury.

■Avoid awkward hand positions where a sudden slip could cause contact

with the rotating bit.

■When drilling, always ensure that the workpiece is clamped securely. It is

dangerous to hold the workpiece in place by hand.

WARNING Do not operate this tool or any machinery while under the inuence

of drugs, alcohol, or medications.

WARNING This product can expose you to chemicals including Acrylonitrile

and other chemicals, which are known to the State of California to cause

cancer and reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Table of Contents

Safety Precautions . . . . . . . . . 2

Pre-Installation/Pre-Assembly. . . 3

Assembly/Setup . . . . . . . . . .4

Operation – Drilling Your First

Pocket Hole . . . . . . . . . . . . 5

Operation – Drilling and Driving

Pocket-Hole Screws . . . . . . . . 7

Accessories . . . . . . . . . . . . 9

Pre-Installation/Pre-Assembly

Review this section before you begin. Ensure you have all parts listed below.

If any item appears missing or lost, do not use this product. Contact Technical

Support or return product to place of purchase.

Part Description

A KPHA730 Kreg Micro-Pocket™ Drill Guide

B Easy-Set Micro-Pocket Drill Bit

C Material Thickness Gauge/Hex Wrench

D Easy-Set Micro-Pocket Stop Collar

Assembly/Setup

a. Remove existing drill guide from the Kreg Jig 720 by squeezing the tabs

(1) on both sides and lifting forward and up to remove the drill guide from

the carriage of the Kreg Jig 720.

b. Insert the Micro-Pocket Drill Guide (A) into the carriage by squeezing

the tabs (1) on both sides of the drill guide carriage, inserting the bottom

tab of the Micro-Pocket Drill Guide (A) into the slot on the carriage and

pressing the top of the Micro-Pocket Drill Guide (A) into place.

The following steps are the same as using the standard size drill guide. See

Owner’s Manual for detailed instruction on the following steps.

Operation – Drilling Your First Pocket

Hole

1 Determine the Material Thickness and Set the

Stop Collar

a. Use the material thickness gauge (C) to determine the material thickness

range.

b. Set the stop collar (D) by placing it on the drill bit (B) and aligning

the window of the stop collar (D) with the material thickness range

determined in step a.

c. Use the hex wrench (C) to lock the stop collar (D) into place on the drill

bit (B).

2 Position your Workpiece

There are two different methods for aligning your Kreg Jig with your workpiece:

■For a workpiece narrower than 1-1/4" wide it is recommended to place

each pocket hole 3/8" from the edge, if possible. To do this, mark 3/8" from

each edge as the center of the pocket hole and align one of the numbered

pocket-hole drill guides (number 1, 2, or 3) and drill the rst pocket hole.

Then, re-position to the second mark and repeat the drilling process.

■For a workpiece between 1-1/4" to 2-1/4", use the board centering mark A

and drilling pocket-holes 1 and 2.

■For a workpiece between 2-1/4" and 3-1/2", use board centering mark B

and drilling pocket-holes 1, 2, and 3.

■For wider workpieces such as a drawer box side, it is recommended

that the pocket-holes be spaced at 3/4" center-to-center spacing. For

workpieces such as panels, it is recommended that the pocket-hole

spacing be 1/2" to 1-1/4" from the edge and then every 4" to 6".

1 2 3 A B C

Board Width Center Mark Drill Guide

1-1/4" to 2-1/4" A 1 and 2

1-1/4" to 2-1/4" C 2 and 3

2-1/4" to 3-1/2" B 1, 2, and 3

Press down on the jig handle in one smooth motion until the jig handle is at

its travel limit. Proceed to the Operation - Drilling and Driving Pocket-Hole

Screws section to start drilling.

Operation – Drilling and Driving

Pocket-Hole Screws

1 Drill Pocket Holes

WARNING When drilling, always ensure that the workpiece is clamped

securely and that the jig handle is pressed down to its travel limit.

a. Place your prepared drill bit (B) with stop collar (D) into your drill.

b. Insert your drill bit (B) into the drill guide (1) and bring your drill up to

speed before contacting the workpiece to ensure correct rotation of the

drill bit.

c. Drill until the stop collar (D) stops going any deeper due to contact

between the stop collar (D) and drill guide (1). Remove the drill bit (B) from

the drill guide (1) while the drill bit is still rotating.

d. When you are nished drilling pocket hole(s), lift the jig handle to release

the clamping pressure; then remove your workpiece.

2 Drive Screws

a. Your Micro-Pocket™ Drill Guide Kit is designed to work with SPS type

screw heads. Ensure you are using the correct screw size according to

this chart:

Gauged Material

Thickness

Easy-Set

Stop Collar

Material

Thickness Stop

Screw Length

1/2 Range 1/2 1/2 1" (25 mm)

3/4 Range 3/4 3/4 1-1/4" (32 mm)

3/4 3/4 1-1/2" (38 mm)

1-1/2 Range 1½ 1½ 2-1/2" (64 mm)

For more information on screw selections, go to www.Kregtool.com/

Screws or simply scan the QR code on the side of your sample screw

package.

Note For some material in the 1/2" range, it may be necessary to use

the SPS-F075 screw to prevent the tip of the screw from exiting the

workpiece.

Note If your material thickness falls in the range, use the same

setup techniques as the 3/4" range with a 1-1/2" screw.

b. Clamp joints in place to ensure a better nished joint. These examples

show face joints and edge joints.

2 Drive Screws (continued)

WARNING When drilling, always ensure the workpiece is clamped securely.

c. Place your screw on your driver tip, position the screw in the pocket hole,

and drive the screw until it is fully seated without overdriving.

Accessories

KPHA750 Pocket-Hole Jig Docking Station

06/2020 104694 V1

EXPLORE. BUILD. SHARE.

We’re makers just like you.

That’s why we love to see what you’re working on.

Share with the community and get inspired!

#madewithKreg

Get free plans, project resources, and more.

kregtool.com and buildsomething.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kreg Zubehör für Elektrowerkzeuge Handbücher

Kreg

Kreg Swing Stop KMS7801 Bedienungsanleitung

Kreg

Kreg KMA4100 Bedienungsanleitung

Kreg

Kreg Straight Edge Guide Bedienungsanleitung

Kreg

Kreg Klamp Vise KKS1050 Bedienungsanleitung

Kreg

Kreg KPHJ310-INT Bedienungsanleitung

Kreg

Kreg Micro-Pocket Drill Guide Kit 530 Bedienungsanleitung

Kreg

Kreg KMS7215 Bedienungsanleitung

Kreg

Kreg Precision Router Lift Bedienungsanleitung

Kreg

Kreg KBK-IP Bedienungsanleitung

Beliebte Zubehör für Elektrowerkzeuge Handbücher anderer Marken

Bosch

Bosch OSC004 Bedienungsanleitung

Rockler

Rockler 57510 Bedienungsanleitung

Bosch

Bosch RA1054 Montageanleitung

Grizzly

Grizzly T10808 Bedienungsanleitung

Kitagawa

Kitagawa SC N Series Bedienungsanleitung

Wolfcraft

Wolfcraft FKS 145 Kurzanleitung

ADAMAS

ADAMAS B32 Bedienungsanleitung

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Bedienungsanleitung

Echo

Echo Speed-Feed Universal 400 LH/RH Bedienungsanleitung

SCHUNK

SCHUNK ROTA TB-TBS-EP Gebrauchsanweisung

Schmid

Schmid RAPID Secure XL Bedienungsanleitung

Drill Master

Drill Master 360X Bedienungsanleitung

Toro

Toro 138-5050 Bedienungsanleitung

jbc

jbc SF-SD Bedienungsanleitung

Bosch

Bosch GTA 3800 Professional Montageanleitung

RG AVAK

RG AVAK MaxDrill Series Bedienungsanleitung

infaco

infaco PW3 Bedienungsanleitung

Gloria

Gloria CUT & BRUSH Bedienungsanleitung