KTM 350 SX-F EU 2015 Handbuch

SETUP INSTRUCTIONS 2015

350 SX‑F EU

350 SX‑F US

350 XC‑F US

Art. no. 3213194en

INTRODUCTION 1

INTRODUCTION

The work described in these setup instructions must be performed before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

Print out the current PDI form found on the KTM DEALER.NET.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the inter-

est of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here.

It is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical specifica-

tions, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt

these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery

options, deviations from illustrations and descriptions, misprints, and other errors. The models portrayed partly contain special equip-

ment that does not belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright

owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead

to the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM-Sportmotorcycle AG

5230 Mattighofen, Austria

1 MEANS OF REPRESENTATION 2

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Denotes a voltage measurement.

Denotes a current measurement.

Denotes a resistance measurement.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Identifies a proprietary name.

Name®Identifies a protected name.

Brand™ Identifies a trademark.

2 SETUP 3

2.1 Unpacking and setting up the vehicle

M00075-10

Packaging 2

–Remove the box and the plastic packaging.

Info

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of supply

is complete on the basis of the enclosed packing list.

–Have a lift stand available.

Lift stand (54829055000)

–Carefully loosen and remove the tension belt of the footrest mount.

Info

An assistant prevents the motorcycle from falling over.

402050-01

–Together with an assistant, take the vehicle off the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

M00075-11

Package 12

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of supply

is complete on the basis of the enclosed packing list.

402051-01

–Have a lift stand available.

Lift stand (54829055000)

–Together with an assistant, take the vehicle off the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

M00077-10

–Remove the cardboard from around the shock absorber.

–Position the angle lever and linkage lever.

–Mount and tighten screw cap .

Guideline

Nut, linkage lever to angle lever M14x1.5 80 Nm (59 lbf ft)

–Mount and tighten screw .

Guideline

Screw, bottom shock

absorber

M10 60 Nm

(44.3 lbf ft)

Loctite®2701™

2 SETUP 4

B00534-10

–Position FI warning lamp with holder . Mount and tighten screw.

Guideline

Remaining screws, chassis M6 10 Nm

(7.4 lbf ft)

–Attach connector to the wiring harness.

–Mount cable holder to the frame.

B00535-10

–Route the clutch line with the clutch master cylinder toward the front between

the upper and lower triple clamps.

–Position the fork legs and tighten the screws of the triple clamp.

Guideline

Screw, top triple clamp M8 17 Nm

(12.5 lbf ft)

Screw, bottom triple clamp M8 12 Nm

(8.9 lbf ft)

Info

Grooves are milled into the side of the top end of the fork legs. The sec-

ond milled groove (from the top) in the fork leg must be flush with the

upper edge of the upper triple clamp.

Position bleeder screws toward the front.

B00375-11

–Remove screws . Take off the handlebar clamps.

–Remove screws . Remove the handlebar holders.

–Place the handlebar holders in the required position. Mount and tighten

screws .

Guideline

Screw, handlebar support M10 40 Nm

(29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar holders evenly.

101020-10

–Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–Position the handlebar clamps. Mount and tighten the screws evenly.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

Info

The markings on the handlebar should be at the center of the handlebar

clamps.

Keep the gap widths equal when tightening.

101017-01

–Position the controls on the right half of the handlebar.

Info

The routing of the cables can be seen in the figure.

2 SETUP 5

101018-01

–Position the controls on the left half of the handlebar.

Info

The figure shows how to route the clutch line and wiring harness.

–Install the front fender. ( p. 7)

–Install the front wheel. ( p. 6)

–Correctly mount the fuel tank breather.

C00138-01

–Mount the handlebar cushion.

–Install the start number plate. ( p. 7)

101019-01

–Mount the footrests with the springs and pins. Secure the pins using the washers

and cotter pins.

Pliers for footrest spring (58429083000)

800035-10

Warning

Risk of injury Battery acid and battery gases cause serious chemical burns.

–Keep batteries out of the reach of children.

–Wear suitable protective clothing and goggles.

–Avoid contact with battery acid and battery gases.

–Keep sparks and open flames away from the battery. Only charge in

well-ventilated rooms.

–In the event of skin contact, rinse with large amounts of water. If battery

acid gets in the eyes, rinse with water for at least 15 minutes and con-

tact a physician.

–Fill the battery.

Info

Read the notes in the battery package.

–Charge the battery. ( p. 9)

–Install the battery. ( p. 8)

–Unpack and mount the KTM PowerParts included in the delivery (optional).

Info

Read the accompanying KTM PowerParts fitting instructions.

–Apply the label included in the delivery (optional).

–Refuel. ( p. 11)

–Position all controls in their exact positions on the handlebar. Tighten all screws.

–Print out the current PDI form found on KTM DEALER.NET and perform the delivery

inspection.

3 WORK 6

3.1 Raising the motorcycle with the lift stand

Note

Danger of damage The parked vehicle may roll away or fall over.

–Always place the vehicle on a firm and even surface.

401942-01

–Raise the motorcycle at the frame underneath the engine.

The wheels must no longer touch the ground.

–Secure the motorcycle against falling over.

Lift stand (54829055000)

3.2 Removing the motorcycle from the lift stand

Note

Danger of damage The parked vehicle may roll away or fall over.

–Always place the vehicle on a firm and even surface.

402001-10

(All SX‑F models)

–Remove the motorcycle from the lift stand.

–Remove the lift stand.

–To park the motorcycle, insert plug-in stand into the left side of the wheel

spindle.

Info

Remove the plug-in stand before riding.

401943-10

(XC‑F US)

–Remove the motorcycle from the lift stand.

–Remove the lift stand.

–To park the motorcycle, press side stand to the ground with your foot and

lean the motorcycle on it.

Info

When you are riding, the side stand must be folded up and secured with

the rubber band.

3.3 Installing the front wheel

Warning

Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.

–Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

M00064-11

–Check the wheel bearing for damage and wear.

» If the wheel bearing is damaged or worn:

–Change the wheel bearing.

–Clean and grease the shaft seal rings and contact surface of the spacers.

Long-life grease ( p. 14)

–Insert the spacers.

–Position the front wheel and insert the wheel spindle.

The brake linings are correctly positioned.

3 WORK 7

M00024-11

–Mount and tighten screw .

Guideline

Screw, front wheel spindle M24x1.5 45 Nm

(33.2 lbf ft)

–Activate the hand brake lever multiple times until the brake linings are in contact

with the brake disc.

–Remove the motorcycle from the lift stand. ( p. 6)

–Pull the front brake and compress the fork powerfully a few times.

The fork legs straighten.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

3.4 Installing the front fender

B01470-10

Main work

–Position the front fender. Mount and tighten screws and .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

Finishing work

–Install the start number plate. ( p. 7)

3.5 Installing the start number plate

C00418-10

–Position the start number plate. Mount and tighten screw .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

The holding lugs engage.

–Position the brake line and clamp. Mount and tighten screw .

3 WORK 8

3.6 Removing the seat

M00035-10

–Remove screw .

–Lift up the seat at the rear, pull it back and then remove it from above.

3.7 Mounting the seat

M00036-01

–Hook in the front of the seat at the collar bushing of the fuel tank, lower it at the

rear and simultaneously it push forward.

–Make sure that the seat is correctly locked in.

–Mount and tighten the screw of the seat fixing.

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

3.8 Installing the battery

C00246-10

Main work

–Insert the battery into the battery compartment with the terminals facing to the

front.

(All SX‑F models)

Battery (YTX4L-BS)

(XC‑F US)

Battery (YTX5L-BS)

–Reconnect rubber band .

Info

Contact disk must be mounted between screw and cable lug 

with the claws facing down.

–Position the positive cable and mount and tighten the screw.

Guideline

Screw, battery terminal M5 2.5 Nm

(1.84 lbf ft)

–Slide positive terminal cover over the positive terminal.

–Position the negative cable and mount and tighten the screw.

Guideline

Screw, battery terminal M5 2.5 Nm

(1.84 lbf ft)

Finishing work

–Mount the seat. ( p. 8)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KTM Motorrad Handbücher

KTM

KTM 690 Duke EU 2016 Handbuch

KTM

KTM 350 SX-F 2021 Bedienungsanleitung

KTM

KTM 50 SX PRO SENIOR LC Bedienungsanleitung

KTM

KTM 1190 RC8 R Track Bedienungsanleitung

KTM

KTM 250 EXC-F EU 2009 Handbuch

KTM

KTM 990 SUPER DUKE Bedienungsanleitung

KTM

KTM 990 Supermoto R USA 2010 Bedienungsanleitung

KTM

KTM 690 SMC R EU 2013 Handbuch

KTM

KTM 450 SX-F Bedienungsanleitung

KTM

KTM 450 SX-F EU Bedienungsanleitung

KTM

KTM 2013 690 SMC R EU Betriebsanleitung

KTM

KTM 450 EXC RACING 2006 Bedienungsanleitung

KTM

KTM 890 ADVENTURE R 2023 Bedienungsanleitung

KTM

KTM 625 SXC 2003 Bedienungsanleitung

KTM

KTM 350 EXC-F EU 2013 Bedienungsanleitung

KTM

KTM 50 SX PRO JUNIOR LC 2004 Bedienungsanleitung

KTM

KTM 790 Duke 2020 Handbuch

KTM

KTM F8475S0 2019 Bedienungsanleitung

KTM

KTM 640 ADVENTURE1999 Bedienungsanleitung

KTM

KTM 250 SX-F US 2015 Bedienungsanleitung

KTM

KTM Adventure 1090 2017 Handbuch

KTM

KTM 690 Enduro R EU 2014 Handbuch

KTM

KTM F8201V5 Handbuch

KTM

KTM 250 EXC 2024 Stücklistenhandbuch

Beliebte Motorrad Handbücher anderer Marken

OHVALE

OHVALE GP-0 Stücklistenhandbuch

Yamaha

Yamaha Star XV19CTSZ 2009 Bedienungsanleitung

HYOSUNG

HYOSUNG ST7 Bedienungsanleitung

Husqvarna

Husqvarna FC 250 2016 Bedienungsanleitung

Ducati

Ducati SCRAMBLER 800 Gebrauchsanweisung

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung

Yamaha

Yamaha 2006 YZF-R1V Bedienungsanleitung

Fantic

Fantic Enduro 125 Bedienungsanleitung

Ducati

Ducati Supersport 750 desmodue Bedienungsanleitung

MV Agusta

MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung

Yamaha

Yamaha XVS650A Bedienungsanleitung

Yamaha

Yamaha YZF-R6T(C) Handbuch

Ducati

Ducati 748 monoposto strada Bedienungsanleitung

ATK

ATK 1988 250 Bedienungsanleitung

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Bedienungsanleitung

Triumph

Triumph Thunderbird Bedienungsanleitung

Yamaha

Yamaha 2006 FJR1300A Bedienungsanleitung

Ducati

Ducati 996 Bedienungsanleitung