KTM 450 EXC-F 2021 Handbuch

SETUP INSTRUCTIONS 2021

450 EXC‑F

450 EXC‑F SIX DAYS

500 EXC‑F

500 EXC‑F SIX DAYS

500 XCF‑W

Art. no. 3214378en

INTRODUCTION

*3214378en*

3214378en

02/2021

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

All specifications contained herein are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right

to modify or delete technical specifications, prices, colors, forms, materials, services, designs, equipment, etc.,

without prior notice and without specifying reasons, to adapt these to local conditions, as well as to stop produc-

tion of a particular model without prior notice. KTM accepts no liability for delivery options, deviations from fig-

ures and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that

does not belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

KTM applies quality assurance processes that lead to the highest possible product quality as

defined in the ISO 9001 international quality management standard.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

450 EXC‑F EU (F8403U9)

450 EXC‑F SIX DAYS EU (F8403U2)

500 EXC‑F EU (F8503U9)

500 EXC‑F US (F8575U9)

500 EXC‑F SIX DAYS EU (F8503U2)

500 EXC‑F SIX DAYS US (F8575U2)

500 XCF-W US (F8575U1)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

SETUP 2

2.1 Transport mode

H02712-01

This vehicle was blocked for transport in the software.

To operate the vehicle, the vehicle electronics must be enabled.

This process is conducted during initial setup in KTM Dealer.net.

Enabling ensures that the initial setup in KTM Dealer.net is docu-

mented.

Enabling can be performed either temporarily, e.g. for a test ride,

or permanently for vehicle handover.

Info

Make sure that the vehicle is permanently enabled before

handing it over to the customer.

2.2 Unpacking and setting up the vehicle

E00851-10

Condition

Packaging V2

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove the separate enclosure and unpack it. Check that

the scope of supply is complete using the enclosed pack-

ing list.

–Have a lift stand available.

Lift stand (78129955100)

–Carefully loosen and remove the tension belt of the footrest

mount.

Info

An assistant prevents the motorcycle from falling

over.

402050-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

–Remove the headlight mask with the headlight. ( p. 19)

2 SETUP

H01768-10

–Position turn signal indicator lamp 1in the combination

instrument rack.

E00850-10

Condition

Packaging V12

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove and unpack the separate enclosure and compo-

nents. Check that the scope of supply is complete using

the enclosed packing list.

–Have a lift stand available.

Lift stand (78129955100)

–Remove the two cable ties on the triple clamp.

402051-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle and components for transport damage.

–Install the shock absorber. ( p. 22)

H01768-10

–Position turn signal indicator lamp 1in the combination

instrument rack.

SETUP 2

402736-10

–Position the connector board and combination instrument

on the upper triple clamp.

–Mount and tighten screws 2.

Guideline

Remaining screws,

chassis

M6 10 Nm (7.4 lbf ft)

–Route the clutch line with the clutch master cylinder

toward the front between the upper and lower triple

clamps.

–Install the fork legs. ( p. 22)

S01414-10

(EXC‑F EU/US, XCF‑W)

–Remove screws 3and take off the handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar holder

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

E00483-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

2 SETUP

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the installed gap widths equal when tighten-

ing.

S01415-10

(EXC‑F SIX DAYS)

–Remove screws 3and take off the handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar holder

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

S01413-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

SETUP 2

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the installed gap widths equal when tighten-

ing.

S03665-01

(All EU models)

–Position the controls on the right half of the handlebar.

E01235-01

(500 EXC‑F US, 500 EXC‑F SIX DAYS US)

–Position the controls on the right half of the handlebar.

S03667-01

(XCF‑W)

–Position the controls on the right half of the handlebar.

S01423-01

(All EU models)

–Position the controls on the left handlebar half.

2 SETUP

S01410-01

(500 EXC‑F US, 500 EXC‑F SIX DAYS US)

–Position the controls on the left handlebar half.

S03666-01

(XCF‑W)

–Position the controls on the left handlebar half.

S01422-01

(EXC‑F SIX DAYS EU, XCF‑W)

Warning

Voiding of the government approval for road use and

the insurance coverage If the combination switch

is mounted, the vehicle’s road permit, if any,

expires.

–Only operate the vehicle in closed-off areas

remote from public road traffic if the combina-

tion switch is installed.

–(Optional) Mount combination switch on the left side.

Info

The figure shows a possible installation position of

the left side combination switch.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KTM Motorrad Handbücher

KTM

KTM 390 Duke 2015 COL Handbuch

KTM

KTM 390 Duke 2016 Bedienungsanleitung

KTM

KTM 200 DUKE 2021 Bedienungsanleitung

KTM

KTM 125 EXC 2015 Handbuch

KTM

KTM 50 SX 2017 Bedienungsanleitung

KTM

KTM 1290 Super Duke R Handbuch

KTM

KTM 2014 65 SX Handbuch

KTM

KTM 250 EXC SIX DAYS TPI 2022 Bedienungsanleitung

KTM

KTM 500 EXC-F 2018 Bedienungsanleitung

KTM

KTM 250 sxf 2016 Betriebsanleitung

KTM

KTM 250 SX-F EU 2017 Bedienungsanleitung

KTM

KTM 690 Enduro R 2019 Bedienungsanleitung

KTM

KTM 390 DUKE 2017 Bedienungsanleitung

KTM

KTM 450 SX-F EU 2009 Handbuch

KTM

KTM 250 SX-F EU Handbuch

KTM

KTM 950 R Bedienungsanleitung

KTM

KTM 1190 Adventure R EU Bedienungsanleitung

KTM

KTM 450 SX-F CAIROLI 2020 Handbuch

KTM

KTM 250 XC EU 2010 Handbuch

KTM

KTM 250 SX-F Bedienungsanleitung

KTM

KTM 990 Adventure USA 2012 Handbuch

KTM

KTM Super Duke 990s Bedienungsanleitung

KTM

KTM 125 MX Bedienungsanleitung

KTM

KTM 500 EXC-F 2023 Bedienungsanleitung

Beliebte Motorrad Handbücher anderer Marken

OHVALE

OHVALE GP-0 Stücklistenhandbuch

Yamaha

Yamaha Star XV19CTSZ 2009 Bedienungsanleitung

HYOSUNG

HYOSUNG ST7 Bedienungsanleitung

Husqvarna

Husqvarna FC 250 2016 Bedienungsanleitung

Ducati

Ducati SCRAMBLER 800 Gebrauchsanweisung

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Bedienungsanleitung

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung

Yamaha

Yamaha 2006 YZF-R1V Bedienungsanleitung

Fantic

Fantic Enduro 125 Bedienungsanleitung

Ducati

Ducati Supersport 750 desmodue Bedienungsanleitung

MV Agusta

MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung

Yamaha

Yamaha XVS650A Bedienungsanleitung

Yamaha

Yamaha YZF-R6T(C) Handbuch

Ducati

Ducati 748 monoposto strada Bedienungsanleitung

ATK

ATK 1988 250 Bedienungsanleitung

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Bedienungsanleitung

Triumph

Triumph Thunderbird Bedienungsanleitung

Yamaha

Yamaha 2006 FJR1300A Bedienungsanleitung