KTM 85 SX 2018 Handbuch
SETUP INSTRUCTIONS 2018
85 SX
Art. no. 3213739en
INTRODUCTION
*3213739en*
3213739en
06/2017
INTRODUCTION
Perform the work described in these setup instructions before the vehicle is delivered to the customer.
Read the setup instructions in their entirety before beginning work.
These setup instructions were written to correspond to the latest state of this series. We reserve the right to make
changes in the interest of technical advancement without at the same time updating this manual.
We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop
are not specified here. It is assumed that the work will be performed by a fully trained mechanic.
All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete
technical specifications, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice
and without specifying reasons, to adapt these to local conditions, as well as to stop production of a particular
model without prior notice. KTM accepts no liability for delivery options, deviations from figures and descriptions,
misprints, and other errors. The models portrayed partly contain special equipment that does not belong to the
regular scope of supply.
© 2017 KTM Sportmotorcycle GmbH, Mattighofen Austria
All rights reserved
Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission
of the copyright owner.
ISO 9001(12 100 6061)
According to the international quality management standard ISO 9001, KTM uses quality assur-
ance processes that lead to the maximum possible quality of the products.
Issued by: TÜV Management Service
KTM Sportmotorcycle GmbH
Stallhofnerstraße 3
5230 Mattighofen, Austria
This document is valid for the following models:
85 SX 19/16 (F6001R9)
85 SX 17/14 (F6001R8)
1 MEANS OF REPRESENTATION
2
1.1 Symbols used
The meaning of specific symbols is described below.
Indicates an expected reaction (e.g. of a work step or a function).
Indicates an unexpected reaction (e.g. of a work step or a function).
Indicates a page reference (more information is provided on the specified page).
Indicates information with more details or tips.
Indicates the result of a testing step.
Indicates a voltage measurement.
Indicates a current measurement.
Indicates a resistance measurement.
Indicates the end of an activity including potential rework.
1.2 Formats used
The typographical formats used in this document are explained below.
Proprietary name Indicates a proprietary name.
Name®Indicates a protected name.
Brand™ Indicates a brand available on the open market.
Underlined terms Refer to technical details of the vehicle or indicate technical terms, which
are explained in the glossary.
2 SETUP
3
2.1 Unpacking and setting up the vehicle
E00850-10
–Open the box.
–Remove the cable tie and wooden frame.
Info
An assistant prevents the motorcycle from falling over.
To avoid damaging the motorcycle during the setup,
leave the protective film on the vehicle until you have
finished.
–Remove the separate enclosure and unpack it. Check that the
scope of supply is complete using the enclosed packing list.
402050-01
–Have a lift stand available.
Lift stand (78929955100)
–Together with an assistant, take the vehicle off the pallet.
–Position the vehicle on a lift stand.
–Check the vehicle for transport damage.
V01038-10
–Loosen screws 1and remove wheel spindle. Lift the front
wheel into the fork, position it, and insert the wheel spindle.
–Mount and tighten the screw of the wheel spindle 2.
Guideline
Screw, front wheel
spindle
M20x1.5 35 Nm (25.8 lbf ft)
V01039-01
–Position the fender. Mount and tighten the screws.
Guideline
Remaining screws,
chassis
M6 10 Nm (7.4 lbf ft)
V01040-01
–Unpack the shock absorber.
–Position the shock absorber. Mount and tighten the screws.
Guideline
Screw, top
shock absorber
M12 60 Nm (44.3 lbf ft)
Loctite®2701™
Screw, bottom
shock absorber
M12 60 Nm (44.3 lbf ft)
Loctite®2701™
2 SETUP
4
V01041-01
–Position the handlebar.
Info
Make sure the cables and wiring are positioned cor-
rectly.
–Position the handlebar clamps. Mount and tighten the screws
evenly.
Guideline
Screw, handlebar
clamp
M8 20 Nm (14.8 lbf ft)
Info
The markings on the handlebar should be at the center
of the handlebar clamps.
Keep the gap widths equal when tightening.
V01042-01
–Position the handlebar cushion and secure with cable ties.
V01043-01
–Attach the start number plate to the brake line.
V01044-10
–Position the start number plate.
The holding lugs engage in the fender.
–Mount and tighten screw 3.
Guideline
Start number plate
screw
M6 4 Nm (3 lbf ft)
–Remove the fuel tank. ( p. 8)
2 SETUP
5
V01045-10
–Mount the service hour counter on the holder.
–Feed the service hour counter cable through the hole Aand
route it under the wiring harness 4along the frame to the
ignition wire.
Tip
Detach cable holder in the area B.
V01046-01
–Wind the cable for the service hour counter around the ignition
wire, and secure it using cable ties.
–Attach cable holder. Tie excess cable together with a cable tie.
–Install the fuel tank. ( p. 9)
T01611-10
–Position the spring in the hole as shown.
V01054-10
–Position the new footrest and pin.
Spring 5engages in area C.
2 SETUP
6
V01055-10
–Press the spring with special tool 6.
Footrest spring plier (79029083000)
The special tool is applied to area Don the footrest.
–Mount pin 7.
V01056-10
–Mount the washer and split pin 8.
–Repeat these steps on the opposite side.
–Mount the frame protector.
V01047-10
–Remove the motorcycle from the lift stand. ( p. 7)
–Operate the hand brake lever several times until the brake lin-
ings are seated correctly against the brake disc.
–Activate the front brake and compress the fork a number of
times forcefully to align the fork legs.
–Tighten screws 9.
Guideline
Screw, fork stub M8 15 Nm (11.1 lbf ft)
–Refuel. ( p. 12)
–Prepare the vehicle according to the specifications in the
KTM Dealer.net for handover to the customer.
3 WORK
7
3.1 Removing the motorcycle from the lift stand
Note
Danger of damage The parked vehicle can roll away or fall over.
–Park the vehicle on a firm and level surface.
0
0
11
402001-10
–Remove the motorcycle from the lift stand.
–Remove the lift stand.
–To park the motorcycle, insert plug-in stand 1into the left
side of the wheel spindle.
Info
Remove the plug-in stand before riding.
3.2 Removing the seat
V00836-10
–Remove screw 1.
–Raise the rear of the seat, pull the seat back, and lift it off.
3.3 Mounting the seat
V00837-01
–Mount the front of the seat on the collar bushing of the fuel
tank, lower the seat at the rear, and push the seat forward.
–Make sure that the seat is correctly locked in.
V00836-10
–Mount and tighten screw 1of the seat fixing.
Guideline
Remaining screws,
chassis
M6 10 Nm (7.4 lbf ft)
3 WORK
8
3.4 Removing the fuel tank
Danger
Fire hazard Fuel is highly flammable.
The fuel in the fuel tank expands when warm and can escape if overfilled.
–Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.
–Switch off the engine for refueling.
–Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.
–If any fuel is spilled, wipe it off immediately.
–Observe the specifications for refueling.
Warning
Danger of poisoning Fuel is poisonous and a health hazard.
–Avoid skin, eye and clothing contact with fuel.
–Immediately consult a doctor if you swallow fuel.
–Do not inhale fuel vapors.
–In case of skin contact, rinse the affected area with plenty of water.
–Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.
–Change your clothing in case of fuel spills on them.
–Keep fuels correctly in a suitable canister, and out of the reach of children.
Preparatory work
–Remove the seat. ( p. 7)
–Turn the tap handle of the fuel tap to the OFF position.
V00842-10
Main work
–Pull off the fuel hose.
Info
Remaining fuel may flow out of the fuel hose.
–Remove screws 1.
V00843-10
–Remove screw 2with the rubber bushing.
–Remove the hose from the fuel tank breather.
Inhaltsverzeichnis
Andere KTM Motorrad Handbücher
KTM
KTM 1998 125sx Bedienungsanleitung
KTM
KTM 450 XC-F Bedienungsanleitung
KTM
KTM 390 Duke 2016 Bedienungsanleitung
KTM
KTM 125 SX EU 2014 Handbuch
KTM
KTM 1190 RC8 Bedienungsanleitung
KTM
KTM 2004 660 SMC Bedienungsanleitung
KTM
KTM 25 EXC 2016 Handbuch
KTM
KTM 890 Adventure L 2021 Bedienungsanleitung
KTM
KTM 250 EXC F SIX DAYS 2023 Bedienungsanleitung
KTM
KTM 125 SX Bedienungsanleitung
KTM
KTM 85 SX 2021 Bedienungsanleitung
KTM
KTM 250 SX-F 2021 Bedienungsanleitung
KTM
KTM 125 EXC EU 2016 Bedienungsanleitung
KTM
KTM 250 EXC-F EU 2011 Handbuch
KTM
KTM 1290 Super Duke GT 2018 Bedienungsanleitung
KTM
KTM 690 Duke USA Bedienungsanleitung
KTM
KTM 625 SXC Leitfaden
KTM
KTM 1190 RC8 R 2014 Handbuch
KTM
KTM F5360R1 Bedienungsanleitung
KTM
KTM 950 SUPER ENDURO R 950 Bedienungsanleitung
Beliebte Motorrad Handbücher anderer Marken
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung
Yamaha
Yamaha 2006 YZF-R1V Bedienungsanleitung
Fantic
Fantic Enduro 125 Bedienungsanleitung
Ducati
Ducati Supersport 750 desmodue Bedienungsanleitung
MV Agusta
MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung
Yamaha
Yamaha XVS650A Bedienungsanleitung
