KTM Freeride E-SM 2016 Handbuch

SETUP INSTRUCTIONS 2016

Freeride E‑SM

Art. no. 3213505en

INTRODUCTION 1

*3213505en*

3213505en

03/2016

INTRODUCTION

The work described in these setup instructions must be performed before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the interest

of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here. It

is assumed that the work will be performed by a fully trained mechanic with the corresponding HV training.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete technical specifications,

prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these to

local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options, devi-

ations from illustrations and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that does not

belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to

the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

5230 Mattighofen, Austria

This document is valid for the following models:

Freeride E-SM EU (F3001P2)

1 MEANS OF REPRESENTATION 2

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates work requiring expert knowledge and technical understanding. In the interest of your own safety, only

have these jobs performed by correspondingly trained KTM technical personnel.

All work identified by this symbol requires a level 1 qualification for high-voltage systems. Only this qualification

authorizes you to perform non-electro-technical work on a vehicle or on units with a high-voltage system.

All work identified by this symbol requires a level 2 qualification for high-voltage systems. Only this qualification

authorizes you to de-energize the electrical system and perform electro-technical work in a de-energized state.

All work identified by this symbol requires a level 3 qualification for high-voltage systems. Only this qualification

authorizes you to perform electro-technical work under voltage.

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which are explained

in the glossary.

2 SAFETY ADVICE 3

2.1 Work rules

The KTM PowerPack does not contain any parts that require maintenance. Do not open the KTM PowerPack under any circumstances.

Special tools are necessary for certain tasks. The tools are not a component of the vehicle, but can be ordered using the number in

parentheses. Example: transmission shaft holder (70029032000)

During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals and seal rings, O-rings, pins, lock washers) must be

replaced by new parts.

In some instances, a thread locker (e.g. Loctite®) is required. The manufacturer instructions for use must be followed.

After disassembly, clean the parts that are to be reused and check them for damage and wear. Change damaged or worn parts.

After you complete the repair or service work, check the operating safety of the vehicle.

2.2 Safety advice

A number of safety instructions need to be followed to operate the vehicle safely. Therefore, read this manual carefully. The safety

instructions are highlighted in the text and are referred to at the relevant passages.

Info

The vehicle has various information and warning labels at prominent locations. Do not remove information/warning labels. If

they are missing, you or others may not recognize dangers and may therefore be injured.

2.3 Degrees of risk and symbols

Warning

Indicates a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.

Caution

Indicates a danger that may lead to minor injuries if the appropriate measures are not taken.

Note

Indicates a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.

Warning

Indicates a danger that will lead to environmental damage if the appropriate measures are not taken.

2.4 Operating and auxiliary substances

Use the operating and auxiliary substances (such as oils and lubricants) specified in the Owner's Manual.

2.5 Fire hazard

Warning

Fire hazard Damaged rechargeable lithium-ion batteries (KTM PowerPacks) present a fire hazard.

Massive mechanical damage may cause an internal cell short circuit and cause the battery to self-ignite.

–Contact the KTM customer service immediately if major damage to the rechargeable lithium-ion battery (KTM PowerPack)

has occurred.

There is no particular fire hazard for this vehicle when the rechargeable lithium-ion battery (KTM PowerPack) is intact.

However, should the vehicle catch fire, inform the fire brigade responsible that an electric vehicle with a rechargeable lithium-ion bat-

tery is on fire.

3 SETUP 4

3.1 Unpacking and setting up the vehicle

C00858-10

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of supply is

complete on the basis of the enclosed packing list.

–To be in compliance with the homologation of the vehicle, mount all of the parts in

the separate enclosure when assembling the vehicle.

Info

It is not necessary to mount all of the parts in the separate enclosure for the

vehicle to operate correctly. However, homologation will not apply if not all

parts from the separate enclosure are mounted.

–Remove the KTM PowerPack. ( p. 17)

–Have a lift stand available.

Lift stand (54829055000)

–Carefully loosen and remove the tension belt of the footrest bracket.

Info

An assistant prevents the motorcycle from falling over.

402050-01

–Together with an assistant, take the vehicle off the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

C00761-10

–Remove screws . Take off the handlebar clamps.

–Remove screws . Take off the handlebar supports.

–Place the handlebar supports in the required position. Mount and tighten

screws .

Guideline

Screw, handlebar support M10 40 Nm

(29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports evenly.

C00860-01

–Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–Position the handlebar clamps. Mount and tighten the screws evenly.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

Info

The markings on the handlebar should be at the center of the handlebar

clamps.

Keep the gap widths equal when tightening.

3 SETUP 5

C00867-01

–Position the front fender and mount and tighten the screws.

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

M00696-01

–Release the axle clamp screws and remove the wheel spindle.

–Install the front wheel. ( p. 11)

C00863-01

–Position the controls on the right half of the handlebar.

C00864-01

–Position the controls on the left half of the handlebar.

402390-01

–Mount the turn signal switch and connect the plug-in connector on the wiring har-

ness.

3 SETUP 6

C00865-01

–Connect all plug-in connectors to the connector retainer.

Info

Make sure the cables and wiring are positioned correctly.

C00866-10

–Position turn signal indicator lamp .

M00697-01

–Mount the handlebar cushion.

C00868-10

–Take off the electrical compartment.

–Connect turn signal relay .

–Route the wiring harness for the rear turn signal and license plate lamp and con-

nect the electrical consumers.

–Mount the electrical compartment.

S01177-10

–Insert the black and violet cables of the bulb included in the separate enclosure

into the socket and position it in the turn signal indicator lamp .

–Position the turn signal on each side and mount and tighten nuts .

–Refit the headlight mask with the headlight. ( p. 20)

3 SETUP 7

M00695-01

–Mount the footrests with the springs and pins. Secure the pins using the washers

and cotter pins.

Pliers for footrest spring (58429083000)

S01178-01

–Mount the license plate holder with the license plate lamp, turn signals, and reflec-

tor.

–Connect the electrical components.

Info

The cable of the left turn signal is marked red.

The cable of the right turn signal is marked green.

C00740-01

–Recharge the 12 V battery. ( p. 16)

–Install the 12 V battery. ( p. 20)

–Unpack and mount the KTM PowerParts included in the delivery (optional).

Info

Read the accompanying KTM PowerParts fitting instructions.

–Apply the label included in the delivery (optional).

M00700-01

–Mount the mirror clamps on both sides.

M01438-01

–Mount and tighten the rear mirror on both sides.

C00869-10

Note

Material damage The ferrite core has a one-way lock.

If the locked ferrite core is reopened, the lock is destroyed.

–Before installing the ferrite core, ensure it is properly positioned.

–Remove screw .

Info

The screw can be reached through a drill hole in the motor cover.

3 SETUP 8

C00870-10

–Remove clamp .

–Remove the cable tie(s).

–Pull the wiring harness and brake line aside slightly.

C00871-10

–Position ferrite core around the lighting wiring harness and close it.

The ferrite core is fully closed and locked.

C00872-10

–Position the wiring harnesses, ferrite core, and brake line on the motor.

–Position clamp .

C00869-10

–Mount and tighten screw .

Guideline

Remaining screws for motor M6 10 Nm (7.4 lbf ft)

The clamp is fully closed but the cable is not pinched.

C00874-01

–Mount the cable tie(s).

–Position all controls in their exact positions on the handlebar. Tighten all screws.

–Carry out the unlocking procedure for the KTM PowerPack. ( p. 13)

–Prepare the vehicle according to the specifications in the KTM Dealer.net for han-

dover to the customer.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KTM Motorrad Handbücher

KTM

KTM 2010 690 SMC EU Handbuch

KTM

KTM 450 EXC-F 2020 Handbuch

KTM

KTM 390 Duke EU Handbuch

KTM

KTM 50 SX PRO SENIOR LC Bedienungsanleitung

KTM

KTM 390 Duke EU 2013 Betriebsanleitung

KTM

KTM 350 EXC-F 2017 Bedienungsanleitung

KTM

KTM 1190 RC8 R EU/UK 2009 Bedienungsanleitung

KTM

KTM SX-E 3 2024 Bedienungsanleitung

KTM

KTM 450 Rally Factory Replica Bedienungsanleitung

KTM

KTM 990 SUPERMOTO R EU Bedienungsanleitung

KTM

KTM Freeride 250 R EU Bedienungsanleitung

KTM

KTM 50 SX 2012 Bedienungsanleitung

KTM

KTM Freeride E-XC 2018 Bedienungsanleitung

KTM

KTM 690 SMC R 2014 Bedienungsanleitung

KTM

KTM 2010 990 Super Duke R Bedienungsanleitung

KTM

KTM 250 sxf 2016 Betriebsanleitung

KTM

KTM 85 SX 2019 Bedienungsanleitung

KTM

KTM 690 Enduro R EU Bedienungsanleitung

KTM

KTM 690 SMC R Handbuch

KTM

KTM 1190 RC8 R EU 2015 Bedienungsanleitung

KTM

KTM Freeride E-XC 2019 Bedienungsanleitung

KTM

KTM LC4 ADVENTURE R 640 2000 Benutzerhandbuch

KTM

KTM 50 MINI ADVENTURE Bedienungsanleitung

KTM

KTM 250 SX 2019 Bedienungsanleitung

Beliebte Motorrad Handbücher anderer Marken

OHVALE

OHVALE GP-0 Stücklistenhandbuch

Yamaha

Yamaha Star XV19CTSZ 2009 Bedienungsanleitung

HYOSUNG

HYOSUNG ST7 Bedienungsanleitung

Husqvarna

Husqvarna FC 250 2016 Bedienungsanleitung

Ducati

Ducati SCRAMBLER 800 Gebrauchsanweisung

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Bedienungsanleitung

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung

Yamaha

Yamaha 2006 YZF-R1V Bedienungsanleitung

Fantic

Fantic Enduro 125 Bedienungsanleitung

Ducati

Ducati Supersport 750 desmodue Bedienungsanleitung

MV Agusta

MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung

Yamaha

Yamaha XVS650A Bedienungsanleitung

Yamaha

Yamaha YZF-R6T(C) Handbuch

Ducati

Ducati 748 monoposto strada Bedienungsanleitung

ATK

ATK 1988 250 Bedienungsanleitung

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Bedienungsanleitung

Triumph

Triumph Thunderbird Bedienungsanleitung

Yamaha

Yamaha 2006 FJR1300A Bedienungsanleitung