Kubota WSM F2880 Bedienungsanleitung

MONTAGEANLEITUNG

ASSEMBLY

INSTRUCTIONS

INSTRUCTIONS POUR LE

MONTAGE

MODELS

MODELES F2880

MODELLS F3680

1BDAIABAP0010

ENGLISH

DEUTSCH FRANÇAIS

PRINTED IN JAPAN

IMPRIME AU JAPON

DRUCK : JAPAN

Code No.

AN . F . 7 - 11 . 8 . AK No de code. K3623-6295-4

Code Nr.

©KUBOTA Corporation 2005

TO THE DEALER

This manual contains procedures intended to assist the dealer in unpacking and assembling the

product before delivering to the customer.

The customer’s purchase is based on confidence in both the product and your store. Observe the

procedures in this manual to assemble and adjust equipment for your customer’s safety and

satisfaction. When fully assembled, check function of each part and feature.

SAFETY FIRST

The following safety alert symbol marks and indication are found throughout this manual in steps

where particular attention is required so as to ensure your safety and to avoid product damage.

Observe the instructions in these warnings where indicated.

3DANGER : Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

3WARNING : Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

3CAUTION : Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

IMPORTANT : Indicates that equipment or property damage could result if

instructions are not followed.

NOTE : Gives helpful information.

ENGLISH

SAFETY

To prevent accidents, read through the following items

before starting work, and always regard safety when

working. It is your responsibility to ensure your safety on

the job.

1. Preparations

(1) Select a work site which is level, sufficiently

spacious and not in the vicinity of dangerous

objects.

(2) Avoid poorly ventilated rooms. Asphyxiation from

exhaust fumes is always a possibility that

accompanies running engine.

(3) Working clothes which may be pinched or caught

in the equipment must not be worn. Loose

clothing can cause serious injury or death.

(4) Always wear a mask and protective goggles

during work when dust or flying debris is thrown

about.

2. Assembly and adjustments

(1) Before assembling equipment, read the assembly

instructions for the product to become familiar

with the equipment and procedures.

(2) Use only adequate and required equipment, tools

and instruments (torque wrench or battery

hydrometer).

(3) Set the parking brake and place blocks in front of

wheels (when they're contacting the ground) to

prevent machine movement.

(4) Lower the attachment or implement to the ground

before assembling or adjusting equipment.

(5) Before working under suspended or raised

equipment, support the equipment or attachment

to prevent the machine from falling or moving out

of place.

(6) Keep fire from cigarettes, matches or other

ignition sources away from fuel, oil, antifreeze and

other flammable materials.

3. After assembly check

(1) Once the equipment is fully assembled, select a

safe place for a test run. Prevent onlookers from

approaching the equipment.

To avoid serious injury or death:

ADo not start engine or operate levers from

anywhere other than the seat.

To avoid serious injury or death:

ADo not bypass-start the equipment. Short

circuiting the starter terminal runs the risk that

the equipment will start operating or moving

unexpectedly.

ENGLISH

UNPACKING AND CHECKING PARTS

BUnpacking Iron crate

1. Take the diagonal member out of the front of the iron

crate.

2. Take the 4 pieces of bolts (M10-1.25) out of both side

of the iron crate.

3. Tie up the iron crate with a nylon band and lift up with

a hoist or fork lift. (Be careful not to damage the

tractor.)

BThe Accessories Packaged Together With

Tractor Models

AFRONT / REAR TIRE are not included in the crate.

No. DESCRIPTION UNIT F2880 F3680

(1) STEERING WHEEL 1

(2) ACCESSORY CASE 1

(3) LINK, LH RH 1

(4) FENDER, EXTENSION 1

(5) SEAT 1

(6) WEIGHT, LARGE 1

(7) WEIGHT, SMALL 1

(8) ASSY COVER

(UNIVERSAL JOINT) 1

ENGLISH

BContents of Accessory Case

No DESCRIPTION

STANDARD ATTACHMENTS

OPERATOR'S MANUAL 1

FUSE (50A) 1

ASSY FUSE, SPARE 1

KEY, STARTER 2

STATEMENT, WARRANTY 1

LABEL (HYDRAULIC LOCK) 1

MOWER LINK FITTING PARTS

2 SHAFT, FULCRUM 2

BOLT M12 x 25 2

PIN, JOINT 14 x 40 2

PIN, JOINT 14 x 100 2

WASHER, PLAIN M14 8

PIN, SPLIT 4

4 LINK (LIFT) 2

SPRING (LIFT) 2

ASSY ROD (LIFT SPRING) 2

NUT 4

ATTACHING WEIGHT

6 COVER, REAR 1

WASHER, SPRING M12 2

NUT M12 2

WASHER, PLAIN M12 2

BOLT M10 x 20 2

ATTACHING AUXILIARY WEIGHT

BOLT M10 x 65 2

WASHER, PLAIN M10 4

NUT M10 2

FRONT TIRE FITTING PARTS

8NUT,TAPER 10

HANDLE PARTS

9 ASSY PAD, STEERING 1

REAR TIRE FITTING PARTS

WASHER, SPRING M12 8

NUT M12 8

WASHER, PLAIN M12 8

SEAT SECURING PARTS

11 WIRE HARNESS, SEAT SWITCH 1

12 FENDER COVER (CENTER) 1

13 BOLT M14 x 35 2

WASHER, PLAIN M14 2

14 PLATE 1

No DESCRIPTION

ENGLISH

ASSEMBLY

BRemoving the Battery

Take out the Battery.

Charge the battery as indicated in the operator's manual.

To avoid personal injury:

AThoroughly read the operator's manual before

charging.

AInsufficient charging will cause the battery to run down

quickly, resulting in premature battery failure.

BFitting the Mower Linkage 1

Align the axial center of right and left links (1) with that of

outer link stay (2). Fix the shaft fulcrum (3) with the M12

tap bolts (4) (one on each side).

BAttaching the Weight

1. Secure the rear cover (1) and the plate (11) to the

machine with the two bolts (2) as shown in the figure

below.

2. Place the weight (3) on the rear cover. Fix the weight

with the two spring washers (4), two plain washers (5)

and two nuts (6).

3. Place the auxiliary weight on the weight (3). Fix the

auxiliary weight (7) with the two bolts (8), four plain

washers (9) and two nuts (10).

ENGLISH

BHoisting the Front Mower

Hoisting

1. Use a crane with capacities of more than 1 ton.

2. Use nylon slings to protect the coated surface of the

front mower.

3. Block or jack

When working on the front mower being lifted, place a

block or jack under the front mower to prevent it from

falling down.

Front mower hoisting position

Hoist the front and back separately.

Front: Mower linkage

Back: Weight

Apply the M18 bolts and nuts to the mower linkage (A)

to prevent slipping.

[Front hoisting positions]

[Rear hoisting positions]

BFitting the Front Tires

Attach the front tires to the front axle with the taper nuts,

five for each tire.

48.1 to 55.9 N-m (4.9 to 5.7 kgf-m, 35.4 to 41.2 ft-lbs)

BFitting the Rear Tires

Fix the rear tires (1) to the rear axle with the four M12 nuts

(2), four M12 spring washers (3) and four M12 plain

washers (4).

69.0 to 73.0 N-m (7.0 to 7.4 kgf-m, 50.9 to 53.8 ft-lbs)

(1) Nylon sling

(2) Nut

(3) M18 bolt

(1) Nylon sling

ENGLISH

BFitting the Mower Linkage 2

1. Attach the lift link (9) to the right and left links (1 and 2)

and the lift arm with the two joint pins (5 and 6), three

plain washers (7) and two split pins (8).

2. Attach the lift spring (10) and lift spring rod assembly

(11), each for right and left.

3. Mount the cover (12) to the lift link (9) by joint pins (13),

plain washers (7) and split pins (8).

BSecuring the Seat

CFitting the seat

1. Connect the wire harness (2) to the OPC switch

behind the seat (1).

2. Put the four plastic collars (3) in between the seat (1)

and seat base (4). Apply the four bolts (5) in place.

AUse the plastic collars (3) and the bolts (5) assembled

to the seat.

3. Connect the seat wire harness (2) to the main wire

harness (6) of the machine.

4. Mount the center fender cover (7) to the fender with

two M14 bolts (8) and two plain washers (9).

L) LEFT HAND: 70 mm

RIGHT HAND: 50 mm

ENGLISH

BConnecting the Steering Wheel

Install the steering wheel (1) to the column and secure it

with the nut (2) and spring washer (3). Attach the pad (4)

onto the steering wheel.

29.4 to 49.0 N-m (3.0 to 5.0 kgf-m, 21.7 to 36.2 ft-lbs)

BAttaching the Extension Fender

Put the insert nut (1) into the machine and secure the

extension fender (2) with the tapping screw (3).

ENGLISH

BApplying the Hydraulic Caution Label

Apply the hydraulic caution label (1) to the back of the seat

base.

BFitting the Battery

Andere Handbücher für WSM F2880

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kubota Traktor Handbücher

Kubota

Kubota G1800 2WS Gebrauchsanweisung

Kubota

Kubota L3301 Bedienungsanleitung

Kubota

Kubota B2301 Gebrauchsanweisung

Kubota

Kubota BX1870 Gebrauchsanweisung

Kubota

Kubota L3301 Bedienungsanleitung

Kubota

Kubota M6040 Gebrauchsanweisung

Kubota

Kubota MX5000 Gebrauchsanweisung

Kubota

Kubota Tractor Bedienungsanleitung

Kubota

Kubota M6S-111 Bedienungsanleitung

Kubota

Kubota Power Krawler M8540 NARROW Gebrauchsanweisung

Kubota

Kubota WSM B1710 Gebrauchsanweisung

Kubota

Kubota M7040SUHD Bedienungsanleitung

Kubota

Kubota B1620 Bedienungsanleitung

Kubota

Kubota LA1154A Bedienungsanleitung

Kubota

Kubota BX1870 Bedienungsanleitung

Kubota

Kubota Power Krawler M8540 NARROW Bedienungsanleitung

Kubota

Kubota B6100HST Bedienungsanleitung

Kubota

Kubota M6800S Gebrauchsanweisung

Kubota

Kubota B2650 Bedienungsanleitung

Kubota

Kubota L2800 Gebrauchsanweisung

Kubota

Kubota T1880 Bedienungsanleitung

Kubota

Kubota ZD221-48 Gebrauchsanweisung

Kubota

Kubota LA340 Bedienungsanleitung

Kubota

Kubota BX231D Bedienungsanleitung

Beliebte Traktor Handbücher anderer Marken

Ariens

Ariens 936051 Bedienungsanleitung

MacDon

MacDon M150 Bedienungsanleitung

Belarus

Belarus 3522.5 Bedienungsanleitung

CARRARO

CARRARO Vigneto Bedienungsanleitung

Cub Cadet

Cub Cadet 3208 Bedienungsanleitung

GREMO

GREMO 1250F Gebrauchsanweisung

HATTAT

HATTAT A90 Bedienungsanleitung

AL-KO

AL-KO Heritage RS 14/82 Bedienungsanleitung

Webb

Webb WE1742SD Bedienungsanleitung

MacDon

MacDon 9250 Bedienungsanleitung

Toro

Toro 03200 Reelmaster 3100-D Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON 5400 Series Bedienungsanleitung

Iseki

Iseki TXG23 Bedienungsanleitung

Toro

Toro 25429 Bedienungsanleitung

New Holland

New Holland T4.80V Bedienungsanleitung

Gravely

Gravely D Bedienungsanleitung

Case

Case JX 90 Bedienungsanleitung

Challenger

Challenger MT265B Bedienungsanleitung