KUHN MAXIMA 2 Bedienungsanleitung

KN188BGB B

OPERATOR'S MANUAL

Precision Seed Drills

MAXIMA 2

Foldable telescopic frame

KN188BGB B

- English - 09-2008

Dear Owner

Precision Seed Drills

MAXIMA 2

$DEAR OWNER

In buying a Kuhn machine you have chosen wisely. Into it have gone years of thought, research and

improvement. You will find, as have thousands of owners all over the world, that you have the best that

engineering skill and actual field testing can produce. You have purchased a dependable machine, but only

through proper care and operation can you expect to receive the performance and long service built into it.

This manual contains all the necessary information for you to receive full efficiency from your machine. The

performance you get from this machine is largely dependent on how well you read and understand this manual

and apply this knowledge. Please DO NOT ASSUME YOU KNOW HOW TO OPERATE AND MAINTAIN YOUR

MACHINE before reading this manual carefully. KEEP THIS MANUAL AVAILABLE FOR REFERENCE. Pass

it on to the next owner if you re-sell the machine.

Your KUHN dealer can offer a complete line of genuine KUHN service parts. These parts are manufactured and

carefully inspected in the same factory that builds the machine to assure high quality and accurate fitting of any

necessary replacements.

About improvements

We are continually striving to improve our products. It therefore reserves the right to make improvements or

changes when it becomes practical to do so, without incurring any obligations to make changes or additions to

the equipment sold previously.

Designated use of the machine

The MAXIMA 2 precision seed drill must only be used for work for which it has been designed:

- Precision drilling.

- Mineral fertilizer placement (depending upon equipment).

- Application of microgranules in combination with drilling (depending upon equipment).

Document illustrations

The illustrations in this manual may be based on one type of machine only. However, all instructions apply to all

machines covered in this manual.

Precision Seed Drills

MAXIMA 2

Contents

$CONTENTS

Dear Owner.....................................................................................................................1

Contents .........................................................................................................................2

Identification of the machine ........................................................................................5

Front view (Basic machine) ............................................................................................................ 5

Rear view (Basic machine).............................................................................................................. 5

Model identification plate................................................................................................................ 6

Optional equipment......................................................................................................................... 7

Safety............................................................................................................................12

Description of symbols used in this document.......................................................................... 12

Safety instructions......................................................................................................................... 13

Location and description of safety decals on the machine....................................................... 23

Road safety equipment and recommendations.......................................................................... 26

Machine specifications................................................................................................27

Description and glossary.............................................................................................................. 27

General technical specifications.................................................................................................. 28

Technical specifications per model ............................................................................................. 29

Sound levels................................................................................................................................... 31

Putting into service......................................................................................................32

Description of control elements................................................................................................... 32

Control box description ................................................................................................................ 32

Coupling and uncoupling.............................................................................................................. 36

Instructions for transport............................................................................................51

Putting the machine into transport position............................................................................... 51

Conformity with the road regulations.......................................................................................... 53

Contents

Precision Seed Drills

MAXIMA 2

Instructions for work....................................................................................................54

Putting the machine into work position ...................................................................................... 54

Adjustments in working position.................................................................................................56

Machine use................................................................................................................................... 85

Optional equipment......................................................................................................94

Clod clearer.................................................................................................................................... 98

Spring assisted clod clearer......................................................................................................... 99

Star shaped trash remover ......................................................................................................... 101

Furrow opening disk ................................................................................................................... 103

Covering scraper......................................................................................................................... 104

Composite intermediate axial press wheel............................................................................... 105

Stainless steel intermediate axial press wheel......................................................................... 107

Furrow closing disks....................................................................................................................110

Standard V-shaped roller .............................................................................................................111

HD V roller.....................................................................................................................................115

"OTIFLEX" 370 x 165 roller......................................................................................................... 120

"OTIFLEX" 500 x 175 roller......................................................................................................... 122

Microgranulator ........................................................................................................................... 124

Fertilizer unit................................................................................................................................ 139

Low flow kit for the fertilizer unit ............................................................................................... 154

Filling auger ................................................................................................................................. 155

Distribution disks ........................................................................................................................ 157

Belt and pulley units.................................................................................................................... 158

Rear PTO output stub.................................................................................................................. 158

Hydraulic blower drive................................................................................................................ 159

Vacuometer .................................................................................................................................. 161

HECTOR 3000 electronic control box........................................................................................ 161

Precision Seed Drills

MAXIMA 2

Contents

Passage control box kit KMS208................................................................................................ 161

Sowing control box kit KMS412 ................................................................................................. 162

Electronic disengagement kit..................................................................................................... 162

65 x 400 depth control wheels.................................................................................................... 162

45 mm (1.8 ’’) spacer and 5 mm (0.2’’) levelling pad................................................................. 163

82 mm (3.2’’) spacer and 5 mm (0.2’’) levelling pad.................................................................. 163

Mechanical hectare counter........................................................................................................ 163

Maintenance and storage..........................................................................................165

Frequency chart........................................................................................................................... 165

Cleaning the machine.................................................................................................................. 167

Lubrication ................................................................................................................................... 168

Maintenance................................................................................................................................. 171

Storage.......................................................................................................................................... 179

Trouble shooting guide .............................................................................................181

Limited warranty ........................................................................................................184

Identification of the machine

Precision Seed Drills

MAXIMA 2

$IDENTIFICATION OF THE MACHINE

1. Front view (Basic machine)

2. Rear view (Basic machine)

Precision Seed Drills

MAXIMA 2

Identification of the machine

3. Model identification plate

Please write below the type and serial number of the

machine. This information is to be indicated to the dealer

for all spare parts orders.

Type: MAXIMA 2

Serial no.:

Identification of the machine

Precision Seed Drills

MAXIMA 2

4. Optional equipment

Tick box corresponding to the equipment fitted on your

machine:

Sowing component

 Kit no. 1676801: Clod clearer with disk coulter for * 1 gauge wheels.

 Kit no. 1676802: Clod clearer with disk coulter for * 1 gauge wheels.

 Kit no. 1676803: Spring assisted clod clearer.

 Kit no. 1676783: Star shaped trash remover.

 Kit no. 1676775: Opener disc solo.

 Kit no. 1676761: Covering scraper.

 Kit no. 1676762: Composite intermediate axial press wheel.

 Kit no. 1676766: Stainless steel intermediate axial press wheel.

 Kit no. 1676790: Furrow closing disks.

 Kit no. 1677235: Standard Rubber V roller 25 mm (1’’).

 Kit no. 1677234: Standard Rubber V roller 50 mm (2’’).

 Kit no. 1677237: Standard smooth steel V roller.

 Kit no. 1677236: Standard notched steel V roller.

 Kit no. 1677241: HD Rubber V roller 25 mm (1’’).

 Kit no. 1677240: HD Rubber V roller 50 mm (2’’).

 Kit no. 1677239: HD smooth steel V roller.

 Kit no. 1677238: HD notched steel V roller.

 Kit no. 1676757: ø370 x 165 mm (1’2’’ x 6.4’’) OTIFLEX roller and covering scrapers.

 Kit no. 1676859: ø370 x 165 mm (1’2’’ x 6.4’’) OTIFLEX roller and furrow closing disks.

 Kit no. 1676758: ø500 x 175 mm (1’7’’ x 6.9’’) OTIFLEX roller and covering scrapers.

 Kit no. 1676863: ø500 x 175 mm (1’7’’ x 6.9’’) OTIFLEX roller and furrow closing disks.

Precision Seed Drills

MAXIMA 2

Identification of the machine

Microgranulator

Fertilizer unit

For the following models:

- M2M08RT000A003

First equipment microgranulator

 Kit no. 1677163:Insecticide microgranulator 8 rows, 100 L (26 US gal) hopper with front blower and fitting on air

duct.

 Kit no. 1677164: Slug pellet microgranulator 8 rows, 100 L (26 US gal) hopper with front blower and fitting on air

duct.

 Kit no. 1677165: Herbicide microgranulator 8rows, 190 (50 US gal) hopper with front blower and fitting on air duct.

Second equipment microgranulator

 Kit no. 1677139: Insecticide microgranulator 8 rows with 100 L (26 US gal) hopper and fitting on air duct.

 Kit no. 1677140: Slug pellet microgranulator 8 rows with 100 L (26 US gal) hopper and fitting on air duct.

 Kit no. 1677292: Herbicide microgranulator 8 rows with 190 L (50 US gal) hopper and fitting on air duct.

For the following models:

- M2M08RT000AG03

First equipment microgranulator

 Kit no. 1677145: Insecticide microgranulator 8 rows with 100 L (26 US gal) hopper and fitting in high position.

 Kit no. 1677146: Anti-slug pellet microgranulator 8 rows with 100 L (26 US gal) hopper and fitting in high position.

 Kit no. 1677147: Herbicide microgranulator 8 rows with 190 L (50 US gal) hopper and fitting in high position.

Second equipment microgranulator

 Kit no. 1677145: Insecticide microgranulator 8 rows with 100 L (26 US gal) hopper and fitting in high position.

 Kit no. 1677146: Anti-slug pellet microgranulator 8 rows with 100 L (26 US gal) hopper and fitting in high position.

 Kit no. 1677147: Herbicide microgranulator 8 rows with 190 L (50 US gal) hopper and fitting in high position.

 Kit no. 1677228: Low flow kit for the fertilizer unit.

 Kit no. 1677227: Loading screw for fertilizer unit fitted with a 1350 L (356 US gal) hopper.

For the following models:

- M2M08RT000AG03

 Kit no. 1677058: Fertilizer 8 rows with 1350 L (356 US gal) hopper and applicators with standard Suffolk coulters.

 Kit no. 1677059: Fertilizer 8 rows with 1350 L (356 US gal) hopper and applicators with non-stop Suffolk coulters.

 Kit no. 1677060: Fertilizer 8 rows with 1350 L (356 US gal) hopper and applicators with non-top disk coulters.

Andere Handbücher für MAXIMA 2

Inhaltsverzeichnis

Andere KUHN Bohren Handbücher

KUHN

KUHN MAXIMA 2 Bedienungsanleitung

Beliebte Bohren Handbücher anderer Marken

Makita

Makita BDF456 Bedienungsanleitung

Black & Decker

Black & Decker LDX220 Bedienungsanleitung

Hitachi

Hitachi DH 40MA Bedienungsanleitung

Challenge

Challenge JO Technisches Referenzhandbuch

Makita

Makita LXFD01 Bedienungsanleitung

Festool

Festool T18+3 Bedienungsanleitung

Milwaukee

Milwaukee M12 FPDX-202X Bedienungsanleitung

EINHELL

EINHELL TE-RH 32 E Bedienungsanleitung

Makita

Makita DHP484 Bedienungsanleitung

Makita

Makita FD05 Bedienungsanleitung

Bosch

Bosch PSB 530 RA Bedienungsanleitung

Maximum

Maximum 054-1359-4 Bedienungsanleitung

Makita

Makita HP332D Bedienungsanleitung

Raider

Raider RDP-HD31H Bedienungsanleitung

Bort

Bort BPM-1400x2 Bedienungsanleitung

Black & Decker

Black & Decker 7266 Bedienungsanleitung

KENT USA

KENT USA TRD1230 Bedienungsanleitung

Bosch

Bosch GSB 19-2 RE Bedienungsanleitung