Kurzweil K2500 Bedienungsanleitung

System Exclusive Protocol

K2500 System Exclusive Implementation

11-1

Chapter 11

System Exclusive Protocol

K2500 System Exclusive Implementation

The MIDI System Exclusive capabilities of the K2500 allow you to manipulate objects in the

K2500’s memory from a computer system, another K2500, or a MIDI data recorder. The

following is a reference to the SysEx protocol used by the K2500. This information can be used

to build a simple object librarian software program. A word of advice—before you begin

experimenting with SysEx, make sure you have saved anything of value in RAM to disk.

NOTE:

To support new features and changes in the K2500 line of products, the internal program

structure has been changed from that of the K2000. Due to these changes, you cannot transfer a K2000

program to a K2500, or a K2500 program to a K2000 via MIDI system exclusive. The K2500 software

will continue to be enhanced, and in the future the K2500 will be capable of accepting K2000 programs

over MIDI. As a result of this, computer based K2000 editor/librarians will not currently work with the

K2500, unless they have been revised to accommodate the changes.

Common Format

In the following discussion, the ﬁelds of the K2500 System Exclusive Protocol messages are

notated as…

field(length)

…where ‘ﬁeld’ is the name of the particular information ﬁeld in the message, and ‘length’ is

either 1, 2, 3, or n, representing the number of sequential MIDI bytes that make up the ﬁeld. A

length of ‘n’ means that the ﬁeld is of a variable length that is determined by its contents or sub-

ﬁelds.

All K2500 SysEx messages have the common format:

sox(1) kid(1) dev-id(1) pid(1) msg-type(1) message(n) eox(1)

‘sox’ is always F0h, and represents start of System Exclusive.

‘kid’ must be 07h, and is the Kurzweil Manufacturer ID.

‘dev-id’ is Device ID. The K2500 will recognize a SysEx message if the ‘dev-id’ is the same is the

SysX ID parameter from the MIDI Receive page (from the top level, press the MIDI mode

button and the RECV soft button.) If the K2500’s SysX ID parameter is set to 127, it will

recognize SysEx messages no matter what the ‘dev-id’ is.

‘pid’ is the Product Identiﬁer, and must be 78h (120 decimal), indicating the SysEx message is

for the K2500.

‘msg-type’ is the identiﬁer of one of the K2500 SysEx messages deﬁned below, and ‘message’ is

the variable-length message contents.

‘eox’ is always F7h, for end of System Exclusive.

Data Formats

K2500 SysEx messages are subdivided into ﬁelds that contain data in different formats. The

various ﬁelds are shown in the Messages section below. Within a message, any ﬁelds for values

that can be bigger than 7 bits are broken into 7 bit chunks. Thus two MIDI bytes gives 14 bits,

three bytes gives 21 bits. The signiﬁcant bits are right justiﬁed in the ﬁeld. All bytes in a ﬁeld

must be present no matter what the value is. For example, an object type of 132 would be split

into two MIDI bytes in a ‘type’ ﬁeld as 01 04:

System Exclusive Protocol

K2500 System Exclusive Implementation

11-2

decimal: 132

binary: 10000100

binary encoding for type(2) field: 0000001 0000100

decimal encoding for type(2) field: 1 4

Object name ﬁelds are sent as a string of ASCII values in a ‘name’ ﬁeld, with one MIDI byte of

zero as a string terminator. For example, the name “Glass Kazoo” would be sent as letters:

G l a s s _ K a z o o <null>

hex encoding for ‘name’ field: 47 6C 61 73 73 20 4B 61 7A 6F 6F 00

Data sizes and offsets are sent in the ‘size’ and ‘offs’ ﬁelds.These values refer to quantities of 8-

bit bytes in the K2500’s memory, which is packed in the ‘data’ ﬁeld.

Binary data in the ‘data’ ﬁeld is sent by in one of two formats, according to the value of the

‘form’ ﬁeld. If the ‘form’ ﬁeld equals zero, the data is transmitted as 4 bits or one “nibble” in

every MIDI byte. If the ‘form’ ﬁeld equals one, then the data is sent as a compressed bit-stream,

with 7 bits per midi byte. The bit-stream format is more efﬁcient for data-transmission, while

the nibble format is easier to read (and write software for).

For example, to send the following four K2500 data bytes,

hex: 4F D8 01 29

decimal: 79 216 1 41

binary: 01001111 11011000 00000001 00101001

eight MIDI bytes are sent in “nibble” format:

hex: 04 0F 0D 08 00 01 02 09

decimal: 4 15 13 80129

binary: 0000100 0001111 0001101 0001000 0000000 0000001 0000010 0001001

ﬁve MIDI bytes are sent in bit-stream format:

hex: 27 76 0 12 48

decimal: 39 118 0 18 72

binary: 0100111 1110110 0000000 0010010 1001000

The bit-stream format can be thought of as taking the binary bits of the K2500 data and, starting

from the left, slicing off groups of 7 bits. Note that the trailing bits are set to zero.

After the ‘data’ ﬁeld, there is another ﬁeld, ‘xsum’. This is a checksum ﬁeld which is calculated

as the least signiﬁcant 7-bits of the sum of all of the MIDI bytes that make up the ‘data’ ﬁeld.

Messages

This section deﬁnes the K2500 System Exclusive message formats. Each message has a message

type (that goes in the ‘msg-type’ ﬁeld; see Common Format, above), followed by the ﬁeld

deﬁnitions of the message.

System Exclusive Protocol

K2500 System Exclusive Implementation

11-3

DUMP = 00h type(2) idno(2) offs(3) size(3) form(1)

…requests the K2500 to send a data dump of an object or portion thereof. ‘type’ and ‘idno’

identify the object. ‘offs’ is the offset from the beginning of the object’s data and ‘size’ describes

how many bytes should be dumped starting from the offset. ‘form’ indicates how the binary

data is to transmitted (0=nibblized, 1=bit stream). The response is a LOAD message:

LOAD = 01h type(2) idno(2) offs(3) size(3) form(1) data(n) xsum(1)

…which writes data into the speciﬁed object, which must exist. Both load and dump operate on

the object data only. The response to a load message will be

DACK = 02h type(2) idno(2) offs(3) size(3)

…meaning “load accepted”, or

DNAK = 03h type(2) idno(2) offs(3) size(3) code(1)

…meaning “load not accepted.” The ‘code’ ﬁeld indicates the cause of the failure, as follows::

code meaning

1 Object is currently being edited

2 Incorrect checksum

3 ID out of range (invalid)

4 Object not found (no object with that ID exists)

5 RAM is full

To request information about an object, use:

DIR = 04h type(2) idno(2)

The ‘type’ and ‘idno’ identify the object. The response is an INFO message:

INFO = 05h type(2) idno(2) size(3) ramf(1) name(n)

This is the response to DIR, NEW, or DEL. If object is not found, ‘size’ will be zero and ‘name’

will be null. ‘ramf’ is 1 if the object is in RAM.

NEW = 06h type(2) idno(2) size(3) mode(1) name(n)

…creates a new object and responds with an INFO message of the created object. The object’s

data will not be initialized to any default values. If ‘idno’ is zero, the ﬁrst available object ID

number will be assigned. If ‘mode’ is 0, the request will fail if the object exists. If ‘mode’ is 1,

and the object exists in ROM, a RAM copy will be made. If ‘mode’ is 1, and the object exists in

RAM, no action is taken.

DEL = 07h type(2) idno(2)

…deletes an existing object and responds with an INFO message for the deleted object. If there

is only a RAM copy of the object, the response will indicate that the object doesn’t exist

anymore. However, if the deletion of a RAM object uncovers a ROM object, the INFO response

will refer to the ROM object. A ROM object cannot be deleted.

System Exclusive Protocol

K2500 System Exclusive Implementation

11-4

CHANGE = 08h type(2) idno(2) newid(2) name(n)

…changes the name and/or ID number of an existing object. If ‘newid’ is zero or ‘newid’ equals

‘idno’, the ID number is not changed. If ‘newid’ is a legal object id number for the object’s type

, then the existing object will be relocated in the database at the new ID number. This will cause

the deletion of any object which was previously assigned to the ‘newid’. If the ‘name’ ﬁeld is

null, the name will not change. Otherwise, the name is changed to the (null-terminated) string

in the ‘name’ ﬁeld.

WRITE = 09h type(2) idno(2) size(3) mode(1) name(n) form(1) data(n) xsum(1)

…writes an entire object’s data directly into the database. It functions like the message

sequence DEL followed by NEW followed by a LOAD of one complete object data structure. It

ﬁrst deletes any object already existing at the same type/ID. If no RAM object currently exists

there, a new one will be allocated and the data will be written into it. The object name will be

set if the ‘name’ string is non-null. The response to this message will either be a DACK or a

DNAK, as with the load message. The ‘offs’ ﬁeld of the response will be zero. The K2500 will

send a WRITE message whenever an object is dumped from the front-panel (using a “Dump”

soft-button), or in response to a READ message.

The ‘mode’ ﬁeld is used to determine how the ‘idno’ ﬁeld is interpreted.

If ‘mode’ = 0:

The ‘idno’ speciﬁes the absolute ID number to write to, which must exist.(must be valid)

If ‘idno’ equals zero, write to the ﬁrst available ID number.

If ‘mode’ = 1

The object is written at the ﬁrst available ID number after what is speciﬁed by ‘idno’.

It doesn’t matter if ‘idno’ is a legal ID number. Remember that for certain object types, the 100s

through 900s banks allow fewer than 100 objects to be stored (for example, the 100s bank will

store preset effects at IDs 100—109 only). In this mode, if ‘idno’ was 313, the object would be

written to ID 400 if available.

READ = 0Ah type(2) idno(2) form(1)

…requests the K2500 to send a WRITE message for the given object. No response will be sent if

the object does not exist.

READBANK = 0Bh type(2) bank(1) form(1) ramonly(1)

…requests the K2500 to send a WRITE message for multiple objects within one or all banks.

‘type’ and ‘bank’ specify the group of objects to be returned in WRITE messages. The ‘type’

ﬁeld speciﬁes a single object type, unless it is zero, in which case objects of all user types will be

returned (see object type table below). The ‘bank’ ﬁeld speciﬁes a single bank, 0-9, unless it is

set to 127, in which case objects from all banks will be returned.

‘form’ requests the format of the binary data in the WRITE messages. If ‘ramonly’ is one, only

objects in RAM will be returned. If ‘ramonly’ is zero, both RAM and ROM objects are returned.

System Exclusive Protocol

K2500 System Exclusive Implementation

11-5

The responses, a stream of complete WRITE messages, will come out in order of object type,

while objects of a given type are in order by ID number, from lowest to highest. If no objects are

found that match the speciﬁcations, no WRITE messages will be returned. After the last WRITE

message, an ENDOFBANK message (deﬁned below) is sent to indicate the completion of the

bank dump.

The K2500 will insert a small delay (50ms) between WRITE messages that it issues in response

to a READBANK message.

A bank dump can be sent in its entirety to another K2500, which will add all of the objects

contained in the dump to its own object database. IMPORTANT: If the K2500 receives a large

bank dump for a bank or banks that already contain objects, errors may result unless the sender

waits for the DACK message before sending the next object’s WRITE message. One way to

avoid transmission errors such as this is to make sure that the bank being dumped is clear in

the K2500 before sending the dump, so that the K2500 will not miss parts of the dump while its

CPU is busy deleting already existing objects. This can be done using the DELBANK message

(deﬁned below). If the destination bank in the K2500 is pre-cleared, it is not necessary to wait

for the DACK before sending. Even if the sender chooses not to wait for the DACK before

sending the next message, it may be necessary to preserve the 50ms delay between the WRITE

messages.

Due to the large amount of incoming data during a bank dump containing many objects, the

receiving K2500 may have a more sluggish response to front-panel use and keyboard playing

during the data transfer. This is normal behavior and the machine will become fully responsive

as soon as the dump is ﬁnished.

DIRBANK = 0Ch type(2) bank(1) ramonly(1)

This is similar to the READBANK message. The DIRBANK message requests an INFO message

(containing object size, name, and memory information) be returned for each object meeting

the speciﬁcations in the ‘type’ and ‘bank’ ﬁelds. Following the last INFO response will be an

ENDOFBANK message.

ENDOFBANK = 0Dhtype(2) bank(1)

This message is returned after the last WRITE or INFO response to a READBANK or

DIRBANK message. If no objects matched the speciﬁcations in one of these messages,

ENDOFBANK will be the only response.

DELBANK = 0Eh type(2) bank(1)

This message will cause banks of objects (of one or all types) to be deleted from RAM. The

‘type’ and ‘bank’ speciﬁcations are the same as for the READBANK message. The deletion will

take place with no conﬁrmation. Speciﬁcally, the sender of this message could just as easily

delete every RAM object from the K2500 (e.g. ‘type’ = 0 and ‘bank’ = 127) as it could delete all

effects from bank 7 (e.g. ‘type’ = 113, ‘bank’ = 7.)

MOVEBANK = 0Fh type(2) bank(1) newbank(1)

This message is used to move entire banks of RAM objects from one bank to another. A speciﬁc

object type may be selected with the “type” ﬁeld. Otherwise, if the “type” ﬁeld is unspeciﬁed

(0), all object types in the bank will be moved. The “bank” and “newbank” ﬁelds must be

between 0 and 9. The acknowledgement is an ENDOFBANK message, with the “bank” ﬁeld

System Exclusive Protocol

K2500 System Exclusive Implementation

11-6

equal to the new bank number. If the operation can’t be completed because of a bad type or

bank number, the ENDOFBANK message will specify the old bank number.

LOADMACRO = 10h

…tells K2500 to load in the macro currently in memory.

MACRODONE = 11h code(1)

…acknowledges loading of macro. Code 0 indicates success; code 1 means failure.

PANEL = 14h buttons(3n)

…sends a sequence of front-panel button presses that are interpreted by the K2500 as if the

buttons were pressed at its front-panel. The button codes are listed in a table at the end of this

chapter. The K2500 will send these messages if the Buttons parameter on the XMIT page in

MIDI mode is set to On. Each button press is 3 bytes in the message. The PANEL message can

include as many 3-byte segments as necessary.

Byte 1 Button event type:

08h Button up

09h Button down

0Ah Button repeat

0Dh Alpha Wheel

Byte 2 Button number (see table)

Byte 3 Repeat count (number of clicks) for Alpha Wheel; the count is the delta (difference)

from 64—that is, the value of the byte minus 64 equals the number of clicks. A Byte

3 value of 46h (70 dec) equates to 6 clicks to the right. A Byte 3 value of 3Ah (58

dec) equates to six clicks to the left. For example, the equivalent of 6 clicks to the

right would be the following message:

(header) 14h 0Dh 40h 46 (eox)

For efﬁciency, multiple button presses should be handled by sending multiple Button down

bytes followed by a single Button up byte (for incrementing with the ‘+’ button, for instance. )

ObjectTypes

These are the object types and the values that represent them in ‘type’ ﬁelds:

Type ID (decimal) ID (hex) ID(hex, ‘type’ field)

Program 132 84h 01h 04h

Keymap 133 85h 01h 05h

Effect 113 71h 00h 71h

Song 112 70h 00h 70h

Setup 135 87h 01h 07h

Soundblock 134 86h 01h 06h

Velocity Map 104 68h 00h 68h

Pressure Map 105 69h 00h 69h

System Exclusive Protocol

K2500 System Exclusive Implementation

11-7

Quick Access Bank 111 6Fh 00h 6Fh

Intonation Table 103 67h 00h 67h

Master Parameters

The Master parameters can be accessed as type 100 (00h 64h), ID number 16. Master parameters

cannot be accessed with any of the Bank messages.

Button Press EquivalenceTable

Button Code (hex) Button Code(hex)

Alphanumeric pad Soft-Buttons ‘A-F’

zero 00 A ‘(leftmost) 22

one 01 B 23

two 02 C 24

three 03 D 25

four 04 E 26

five 05 F (rightmost) 27

six 06 AB 28

seven 07 CD (two center) 29

eight 08 EF 2A

nine 09 YES 26

+/- 0A NO 27

Alphanumeric pad Edit/Exit

CANCEL 0B EDIT 20

CLEAR 0C EXIT 21

ENTER 0D

Navigation Mode Selection

Plus (+) 16 PROGRAM 40

Minus (-) 17 SETUP 41

Plus and Minus 1E QUICK ACCESS 42

CHAN/BANK Inc 14 EFFECTS 47

CHAN/BANK Dec 15 MIDI 44

CHAN/BANK Inc/Dec 1C MASTER 43

Cursor Left 12 SONG 46

Cursor Right 13 DISK 45

Cursor Left/Right 1A

Cursor Up 10

Cursor Down 11

System Exclusive Protocol

K2500 System Exclusive Implementation

11-8

Cursor Up/Down 18

The next four commands allow you to read the screen display, both text and graphics layers.

ALLTEXT = 15h

…requests all text in the K2500’s display.

PARAMVALUE = 16h

…requests the current parameter value.

PARAMNAME = 17h

…requests the current parameter name.

GETGRAPHICS = 18h

…requests the current graphics layer.

SCREENREPLY = 19h

This is the reply to ALLTEXT, PARAMVAL, PARAMNAME, GETGRAPHICS, or

SCREENREPLY.

The reply to ALLTEXT will be 320 bytes of ASCII text (the display has 8 rows of 40 characters

each). If you receive less than that, then the screen was in the middle of redrawing and you

should request the display again.

The reply to PARAMVALUE will be a variable length ASCII text string. Some values (like

keymaps, programs, samples, etc.) include their ID number in the text string (e.g., "983 OB

Wave 1"). Some messages are also padded with extra spaces.

The reply to PARAMNAME will be a variable length ASCII text string. In cases where there is

no parameter name (like on the program page) there will just be the single 00 null terminator.

The reply to GETGRAPHICS will be 2560 bytes of information. The 6 least signiﬁcant bits of

each byte indicate whether a pixel is on or off. If pixels are on over characters, the text becomes

inverted. Characters on the K2500 display are a monospaced font with a height of 8 pixels and

a width of 6 pixels.

Andere Handbücher für K2500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kurzweil Synthesizer Handbücher

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910252 APPENDIX... Technisches Dokument

Kurzweil

Kurzweil K2600 BEST OF VAST - REV A Technisches Dokument

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910252 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil PC88 Bedienungsanleitung

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910252 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil MARK 12 V2.0 - ADDENDUM Handbuch

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910252 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910252 APPENDIX... Technisches Dokument

Kurzweil

Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910330 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910251 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K2000 - MUSICIANS GUIDE Bedienungsanleitung

Kurzweil

Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910330 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K2600 BEST OF VAST - REV A Technisches Dokument

Kurzweil

Kurzweil MP120A Bedienungsanleitung

Kurzweil

Kurzweil PC3A8 Bedienungsanleitung

Kurzweil

Kurzweil K2500 Bedienungsanleitung

Kurzweil

Kurzweil K2600 - MUSICIANS GUIDE REV A PART NUMBER 910331 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil PC3K Series Bedienungsanleitung

Kurzweil

Kurzweil K2500 - PERFORMANCE GUIDE REV F PART NUMBER 910251 CHAP... Bedienungsanleitung

Kurzweil

Kurzweil K150 - ANNOTATED PROGRAM LIST Bedienungsanleitung

Kurzweil

Kurzweil K2600 BEST OF VAST - REV A Bedienungsanleitung

Kurzweil

Kurzweil K2500 Bedienungsanleitung

Kurzweil

Kurzweil K2000R Bedienungsanleitung

Beliebte Synthesizer Handbücher anderer Marken

Kawai

Kawai MP7 Technisches Handbuch

Joranalogue

Joranalogue Contour 1 Bedienungsanleitung

Full Bucket Music

Full Bucket Music Mono/Fury Bedienungsanleitung

Kawai

Kawai PH50 Bedienungsanleitung

IK Multimedia

IK Multimedia UNO Synth PRO X Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Roland

Roland Gaia SH-01 Bedienungsanleitung

Roland

Roland GR-30 Bedienungsanleitung

Gotharman

Gotharman Gotharman's anAmoNo-box Bedienungsanleitung

Yamaha

Yamaha DX21 Bedienungsanleitung

QuStream

QuStream HDFS-550 Bedienungsanleitung

Modal Electronics

Modal Electronics ARGON8 Bedienungsanleitung

Roland

Roland GS-500 Bedienungsanleitung

Octave

Octave Cat SRM Bedienungsanleitung

Dreadbox

Dreadbox Murmux Initiate Bedienungsanleitung

neutral labs

neutral labs ELMYRA 2 Bedienungsanleitung

Waldorf

Waldorf KYRA Bedienungsanleitung

Tubbutec

Tubbutec Juno-66 Bedienungsanleitung