KVH Industries TracVision M9 Leitfaden

KVH, TracVision, and the unique light-colored dome with contrasting baseplate are registered trademarks of KVH Industries, Inc.

All other trademarks are property of their respective companies. The information in this document is subject to change without notice.

These instructions explain how to replace the PCB module in a TracVision M9 antenna.

Installation Steps

Tools Required

This procedure requires the following tools:

Technical Support

If you need technical assistance, please contact KVH Technical Support:

1. Remove the Radome, 2

2. Replace the PCB Module, 2

3. Configure the Antenna, 4

4. Reinstall Satellites, 5

• Phillips screwdrivers

•Cuttingpliers

• 7/16" open-end wrench

• PC with latest version of the Flash Update

Wizard installed

• Digital level (or equivalent)

N. America, S. America, Australia:

Phone: +1 401 847-3327

E-mail: [email protected]

Europe, Middle East, Asia:

Phone: +45 45 160 180

E-mail: [email protected]

Be sure to trim the excess portion of any tie-wraps you install and collect all tie-wrap

trimmings from the antenna to avoid damage when the unit rotates.

IMPORTANT!

PCB Module Replacement Instructions for

TracVision®M9

Step 1 - Remove the Radome

Follow the steps below to remove the radome.

a. Disconnect power from the TracVision

system and any connected receivers and/or

multiswitch.

b. Remove the eight Phillips screws securing the

radome (see Figure 1). Then remove the

radome and set it aside in a safe place.

Step 2 - Replace the PCB Module

Follow the instructions below to replace the PCB

module.

a. Using cutting pliers, cut and remove the tie-

wrap securing the cables to the back of the

PCB module (see Figure 2).

CAUTION

For your own safety, be sure to disconnect

power from all wired components before

performing this procedure.

Figure 1 Radome Screws

Figure 2 Tie-wrap on PCB Module

#10-32 Screw (x8)

Baseplate

Radome

Tie-wrap

b. Apply labels to the RF cables connected the

RF PCB (see Figure 3). You will need to

connect each cable to the same connector on

the new unit later.

c. Using a 7/16" open-end wrench, disconnect

the RF cables connected to the RF PCB (see

Figure 3).

d. If your system includes an inverter PCB, use

a screwdriver to loosen the two Phillips

screws securing the inverter PCB to the RF

PCB. You do not need to disconnect any

cables.

e. Disconnect all of the connectors from the

bottom of the PCB module. You will need to

connect each cable to the same connector on

the new unit later. Refer to the connector key

and label the cables as necessary.

f. Using a screwdriver, loosen the four Phillips

screws securing the PCB module to the

antenna frame.

g. Remove the PCB module.

h. Reverse these instructions to install the new

PCB module. Then proceed to “Step 3 -

Configure the Antenna” on page 4.

NOTE: Leave the radome off for now. You will

reinstall the radome later.

Figure 3 RF PCB Connections

Figure 4 PCB Module Screws/Connectors

Inverter

PCB

Screw (x2)

RF PCB

Cables

Connector

Key

Screws (x4)

Connectors

Step 3 - Configure the Antenna

Follow the steps below to configure the antenna

to use the new PCB module. This procedure

requires a PC with the latest version of the Flash

Update Wizard installed.

NOTE: If you do not have the KVH Flash Update

Wizard installed, you can use Windows®

HyperTerminal instead. Be sure to establish the

following settings: bits per second: 9600, data bits: 8,

parity: none, stop bits: 1, flow control: none.

a. Connect one end of a PC data cable to the

maintenance port on the rear of the MCU (see

Figure 5). Connect the other end to your PC.

NOTE: If your computer does not have a DB9

connector, you can use the following USB-to-RS232

adapters: Belkin part # F5U409 or # F5U109, or

IOGear part # GUC232A.

b. Apply power to the TracVision system.

c. Open the KVH Flash Update Wizard. You

will type the following commands into the

Flash Update Wizard’s “command” box.

d. Type HALT then press Enter.

e. Type DEBUGON then press Enter

f. Type =TVM9 then press Enter.

g. Type ZAP then press Enter to restart the

system.

h. Wait two minutes for system startup.

i. Type HALT then press Enter.

j. Type DEBUGON then press Enter.

k. Type EL,300 then press Enter.

Figure 5 MCU Maintenance Port

Maintenance

Port

l. Using a digital level, measure and record the

angle of the feed tube, as shown in Figure 6.

m. Type =CALUP,XX.X where xx.x is the

number you recorded in Step l.

n. Type =CALGYRO then press Enter. Wait

two minutes while the azimuth and elevation

gyros calibrate.

o. Type ZAP then press Enter to restart the

system.

p. Reinstall the radome.

Step 4 - Reinstall Satellites

The TracVision M9 system must now be set to

track the satellites of your choice. Follow the

instructions provided in the TracVision M9

User’s Guide to set the system to track your

selected satellites.

The procedure is complete!

Figure 6 Measuring the Feed Tube

Feed Tube

Inhaltsverzeichnis

Andere KVH Industries Antenne Handbücher

KVH Industries

KVH Industries TracVision R5SL Bedienungsanleitung

KVH Industries

KVH Industries TracPhone F55 Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD7 LNB Leitfaden

KVH Industries

KVH Industries TracPhone V11 Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Leitfaden

KVH Industries

KVH Industries TracPhone V7 Bedienungsanleitung

KVH Industries

KVH Industries 5616 Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V7 HTS Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V7-HTS Leitfaden

KVH Industries

KVH Industries TracPhone V7-IP Bedienungsanleitung

KVH Industries

KVH Industries TracVision Land Mobile Antenna Leitfaden

KVH Industries

KVH Industries TracVision A9 Bedienungsanleitung

KVH Industries

KVH Industries TracVision HD11 Leitfaden

KVH Industries

KVH Industries TracPhone V11 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision R6 DX Leitfaden

KVH Industries

KVH Industries TracPhone V7-IP Bedienungsanleitung

KVH Industries

KVH Industries TracVision M9 Leitfaden

KVH Industries

KVH Industries TracVision UHD7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision A9 Bedienungsanleitung

KVH Industries

KVH Industries TrackPhone V7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Leitfaden

KVH Industries

KVH Industries TracVision TV6 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung