Kwikee Level best 2000 Bedienungsanleitung

Table of Content

Page

Introduction 1

Safety Information 1

Operation 2

Control Panel 3

Manual Mode 3

Auto Mode 3

Stabalizing 4

Retracting Jacks 4

Setting Level Sensor 5

Care and Maintenance 5

Trouble Shooting Guide 6

Error Codes 6

Control Panel Jumper 7

Limited Warranty 8

Operation

Guide

Operation Guide

Products Company, Inc.

230 Davidson Avenue

Cottage Grove, Oregon 97424

(541) 942-3888

www.kwikee.com

Kwikee Doc #1421901 Rev. Feb. 2004

Hydraulic Leveling Systems #2000, #2010, #3000, and #30130

The Level Best leveling and stabilizing system is an electronically controlled/hydraulical-

ly operated unit that consists of a 12 volt DC powered motor/pump/manifold assembly

with fluid reservoir, hydraulic hoses, four hydraulically operated jacks, a control unit with

switch panel, and optional level sensor unit and pressure sensor. It is designed to meet

the varying requirements of vehicles ranging from class “C” motorhomes to the large

class “A” motorhome.

If, after thoroughly reading this manual, you still have questions in regard to the opera-

tion and maintenance of the Level Best system, please contact the Kwikee Service

Department at 1-800-736-9961.

WARNINGS

Do not use the Level Best system as a lift for changing tires or working

under the vehicle.

Never check for hydraulic fluid leaks using your hands and/or any other body part. The

leaking fluid is under pressure and is capable of cutting and penetrating your skin

resulting in severe injury.

When extending the rear stabilizers, do not lift the wheels beyond ground contact. This

overrides the braking effect of both the transmission park and parking brake. Without

this braking, it is possible for the vehicle to roll unexpectedly forward (or backward) off

the jacks. This could cause severe injury or even death.

Holding a control switch in the "extend" or "retract" position for a time period longer

than necessary to fully extend or retract the hydraulic cylinders, can cause overheating

and damage to the pump motor as well as the electrical components.

Do not use the leveler as an emergency brake, They are not designed for any type of

vehicle braking purpose.

Do not use the levelers on icy or slick surfaces on which the foot pads may slip.

IN THE EVENT OF ACCIDENTAL EXTENSION

1. Bring the vehicle to a safe and complete stop as soon as possible.

2. Turn the leveling systems power switch on and press the all up switch.

3. Visually inspect the vehicle undercarriage for any problems.

Introduction

The control panel consists of switches and light

emitting diode indicators (Figure 1).

The switches include main power ON/OFF, all jacks

retract (ALL UP), a diamond shaped switch for bi-

lateral leveling

(BI-LEVEL), and four (UP/DN) switches for

independent extension and retraction of the jack

legs. The position of the UP/DN switches correspond

to the postion of the jack legs on your motor home,

with the front of the vehicle indicated by the top of

the panel.

The AUTO LEVEL switch only appears on motor

homes equipped with fully-automatic leveling.

Figure 1: Fully-automatic touchpad control panel shown.

The Level Best system performs the dual function of leveling the vehicle and, once a level

plane has been achieved, stabilizing the vehicle. When leveling the vehicle, it may not be

necessary to use all of the leveling jacks however, to stabilize the vehicle, all jacks should be

extended to contact the ground.

SITE SELECTION

1. When selecting a site for parking the vehicle, choose a spot that is as flat as possible -

this will minimize the extent of leveling.

2. Check that the area under the vehicle is free from any obstacles that might interfere with

the operation of the levelers. Check the ground surface to assure the leveler feet have a flat

solid surface for contact. When parking on grass, soft dirt and/or uneven terrain, it is

advisable to extend the surface area of the leveler feet by using pads. These pads can be

from 3/4" plywood, cut into 12" squares.

NOTE: In occasional adverse driving conditions, it is possible for mud, ice and other debris to

accumulate around the leveler units. This debris may interfere with the operation and should

be cleaned off prior to using the system.

CAUTION: Do not compensate for uneven terrain by using pads that are thicker than

3". Pads that are thicker than the leveler's vertical ground clearance can prevent

breaking contact with the ground when retracting. This can result in damage to both

the levelers and the vehicle.

NOTE: To prevent improper

operation of the leveling

system, which could result in

damage to the levelers and/or

the vehicle itself, read the

operating instructions

carefully before using the

leveling jacks.

Operation

Level Best Operation Guide Page 2

To stabilize the vehicle once it has been leveled, any unused leveler must be extended into

firm contact with the ground. Accomplish this by using the appropriate individual leg leveling

switch so as not to affect the level of the coach.

CAUTION: Overextending the levelers during stabilizing will cause the vehicle to

become unlevel and result in a loss of stability. If a leveler has been overextended,

press the ‘up’ portion of the respective switch until the vehicle lowers into the level

plane again. Do not attempt to use the other levelers to raise the vehicle to a higher

level plane.

Control Panel Functions

Manual Leveling

The ON/OFF switch, located in the upper left hand corner, controls the supply of power for all

panel functions, activation of this switch is indicated by its green LED.

The ALL UP (leg retract) switch is located in the lower left hand corner of the control panel.

Activation of this switch causes all legs to retract to the travel position. When the retract

sequence is completed the ALL UP LED will turn green to indicate that it is now safe to move

the motor home.

The diamond shaped BI-LEVEL switch, located in the center of the panel, activates the

extension of the leveling jacks in pairs. Use of this switch greatly simplifies the leveling

process and significantly reduces the amount of stress created by the leveling process on the

motor home. Operation of this switch illuminates the yellow LED’s corresponding to the jacks

that are being activated. The LED will illuminate in manual version only.

The four UP/DOWN switches control the leveling jacks independently. Pushing these

switches operates the corresponding jack causing it to retract (UP) or extend (DN). Operation

of this switch lights the yellow LED corresponding with the jack activated. The LED will

illuminate in manual version only.

Level Best Operation Guide Page 3

SEMI-AUTOMATIC FUNCTION When an AUTO MODE sensor is connected to

a manual control, the jack indicator lights act as an indicator of the level

condition of the coach. A light that is ‘on’ indicates the high corner of the

coach. Push the BI-LEVEL pair button corresponding to the end of the coach

you would like to raise. When the light comes ‘on’, stop the action of that

button. In this way the jack indicator lights act as a bubble-level, indicating

the level condition of the coach.

FULLY-AUTOMATIC FUNCTION Coaches equipped with AUTO MODE

can be operated the same as manual or semi-automatic versions. The fully-

automatic unit functions the same until the AUTO MODE switch is pressed.

Pushing the AUTO MODE switch causes the system to extend a pair of jack legs

to the ground. Next the other pair of legs is extended to the ground and the system

begins the auto level sequence. During the auto level sequence the system will run

one to three of the jacks depending on the level condition of the coach. On completion,

the system will check the level condition of the coach and either re-run the sequence

or display a green LED light under the AUTO MODE button to indicate that the

sequence is complete. Typical coach level capability is 0.3 degrees from side to

side and front to rear.

Automatic Leveling

Level Best Operation Guide Page 4

1. Start the chassis engine and turn the control panel power switch on. If any levelers are

extended, the control panel will emit a warning beep and the red "ALL UP" LED will light up

and flash.

2. To retract all levelers simultaneously, press the "ALL UP" switch. To retract each leveler

individually, press and hold the "UP" side of the respective leg switch. Using the "ALL UP"

switch is the recommended method of retracting the levelers to assure even retraction at all

four leveler locations and eliminate the possibility of twisting the chassis frame.

3. When all leveler legs retract to the travel position, the red "ALL UP" LED will turn green,

and the pump will shut off. You can now turn off the power switch and the vehicle is ready to

travel.

Retracting the Levelers

Observing the precautions set forth on the previous pages of this manual, you are now ready

to begin leveling your motor home. With the vehicle engine running, place the transmission in

park and set the parking brake. Securely block the wheels using wheel chocks.

Locate the "ON/OFF" button on the upper left of the control panel. Momentarily depress this

switch to activate the leveling system. The LED will light up and be a steady green indicating

that the system is ready. If the LED lights up and is flashing, it is an indication that the park-

ing brake is not completely engaged or the transmission is not in park.

Reference you’re leveling tool to determine which corner of the motor home is lowest. Using

one of the "BI-LEVEL" switches which represent the front and rear of the motor home. Use

the switch that corresponds to the low end of the motor home. Depress and hold the switch

to raise the sides of the motor home until level. Now find and depress the "BI-LEVEL" switch

which represents the low side of the motor home, and hold it until the front and rear of the

motor home are level.

Your motor home should now be in a level plane. If the coach has settled slighting, you

should fine-tune your position by using the individual leg leveling switches. Push the ‘’DN”

portion of the switch to raise the vehicle and the “UP” portion to lower the vehicle.

Stabilizing

NOTE: To prevent the

possibility of damaging the

levelers and/or vehicle, it is

good common sense to

confirm the retracted position

by visual inspection.

The Level Best hydraulic leveling system should be routinely checked as part of a

regular vehicle maintenance program. Kwikee recommends checking the system twice

a year: in the spring prior to the heavy travel season and in the winter, prior to storage.

The following checklist has been provided as a guideline for maintenance.

1. Be sure the leveling jacks are in the retracted position. Remove the breather cap

on the reservoir and check the fluid level in the reservoir. The fluid level should be

approximately 1" below the top of the reservoir. This standard provides an adequate

amount of fluid for the levelers to operate efficiently. If the fluid is below this level, add a

sufficient amount to bring the level up to the operating standard. When filling the

reservoir, use transmission fluid only. We recommend Dexron III. Do not mix fluids.

2. Check wire connections at motor and valve manifold; should be tight and secure.

3. Check the valve manifold for any evidence of hydraulic fluid leakage. Replace any

seals as needed.

4. Examine the hydraulic hoses for damage and/or leakage. Replace and resecure as

needed.

5. Check hydraulic cylinders and leg assemblies for damage and/or leakage. Replace

and/or repair as needed. Verify that all mounting bolts have been tightened to 80ft/lbs.

Care and Maintenance

Turn on the coach ignition and press the ON/OFF button on the control. The two top

indicator lights above the right and left front jack buttons will start flashing. The lights

indicate the warm up cycle of the level sensor. Aftr the warm up cycle the lights will stop

flashing. The cycle usually lasts between 2 and 10 minutes depending on outside

temperatures and whether it was previously run. The control will time-out every 60

seconds but the level sensor will continue to go through the warm up cycle anytime the

ignition of the coach is on.

When the warm up cycle is complete, turn off the control by pressing the ON/OFF

button. With the coach in a level attitude press and hold the ALL UP, BI-LEVEL FRONT

and BI-LEVEL REAR buttons simulaneously. You should hear an audible beep. Turn the

control back ‘on’ and all four indicator lights should now be lit indicating the level sensor

is showing the coach to be level. If all four LEDs are not illuminated, repeat last 2 steps.

Setting Level Sensor (if so equipped)

Level Best Operation Guide Page 5

NOTE: During periods of

vehicle inactivity and/or

storage, the leveling system

should be activated and

cycled through the

leveling/retracting procedures

on a monthly basis to keep

the levelers in good operating

condition.

Level Best Operation Guide Page 6

Troubleshooting

1. Panel does not function (buttons and lights do not work/system does not respond.)

• Ignition needs to be on with engine running

• Transmission needs to be in park and parking brake applied.

2. Red indicator light will not go out when legs are retracted.

• Reed switch(es) not grounded or reed switch is defective.

3. The action of one cylinder will not operate in one direction (i.e., it will go down,

but not up, or vice versa).

• Hydraulic hoses and/or wiring connections are crossed

• Valve not operating.

4. Jacks won‘t extend after they had been working previously.

• Directional valve is not shifting positions - possibly due to foreign object

obstructing the valve itself, or the solenoid is not working properly.

5. Pump continues to run after switch is released.

• Pump motor solenoid is stuck - tap solenoid to unstick it or replace the solenoid.

6. To retract jacks with a control failure, see Control Panel Jumper Instructions

on Page 7.

This list represents a cross section of some possible problems and the corresponding

solutions. After reviewing the manual, if you still have problems or questions, please

contact the Kwikee Service Department at 1-800-736-9961.

LED 7 green.

• Jacks retracted fully.

LED 7 red. Audible beep for approximately 8 seconds.

• Jacks deployed.

LED 6 green.

• Unit turned ‘on’.

LED 6 flashes.

• Park brake not set.

LEDs 1 and 2 flash.

• Level sensor in warm-up cycle.

LED 5 green and audible beep.

• Auto level sequence completed satisfactorily.

Standard Operating Codes

Alternating LEDs 1 and 2 ‘on’, then 3 and 4 ‘on’ etc.

• Coach tilted too far front to back to level.

Alternating LEDs 1 and 3 ‘on’, then 2 and 4 ‘on’ etc.

• Coach tilted too far side to side level.

LED 5 flashes red.

• Jacks are out of stroke.

LED 5 flashes green/red.

• Lost communication with Auto Level Sensor.

Auto Level Error Codes

LED Positions

Level Best Operation Guide Page 7

Control Panel Jumper Instructions

To be used in the event of a control failure.

1. Remove the control panel from the bezel and disconnect the wire harness.

(See Figure 2.)

2. Make sure the area around and below the motorhome is clear of all obstructions

and that no personnel are under the vehicle.

3. Plug the large connector of the jumper assembly into the wire harness (Figure 3.)

4. Plug the 4-way connector into the wire harness. CAUTION: Pump will start

immediately and the jacks will begin to retract. (See Figure 3.)

5. After jacks have been fully retracted, immediately disconnect the 4-way connector

on the jumper assembly from the wire harness to shut off the pump (Figure 3.)

Failure to immediately remove the 4-way connector can cause over-heating

of the pump motor and permanent damage to the system.

6. Remove the large connector of the jumper assembly from the wire harness.

7. Have jack system serviced at a qualified service center prior to using the jack

system.

Figure 2: Disconnect the wire

harness from the back of the

control panel.

Figure 3: Attach the Jumper Assembly to the Wire Harness.

NOTE: Immediately disconnect the 4-way connector after the jacks are fully

retracted. Failure to immediately remove the 4-way connector can cause

over-heating of the pump motor and permanent damage to the system.

4-WAY

CONNECTOR

JUMPER

ASSEMBLY

WIRE

HARNESS

CONTROL

PANEL

WIRE

HARNESS

Products Company, Inc.

230 Davidson Avenue

Cottage Grove, Oregon 97424

(541) 942-3888

Level Best Operation Guide Page 8

NOTE: Any parts returned for warranty service/repair with wires cut will result in

voiding of the warranty.

NOTE: It is important to read and understand this manual thoroughly before

initiating any installation of the jacks. Kwikee Products Company, Inc., assumes no

liability for damages or injury resulting from the improper installation or operation of

the Level Best® Hydraulic Leveling/Stabilizing System.

Kwikee Products Company, Inc. (“Kwikee”) warrants to the original purchaser that the Level Best®

hydraulic leveling/stabilizing system is free from defects in material and workmanship for a period of

5 years from the date of purchase. Kwikee’s obligation under this warranty is limited to the repair or

replacement of defective parts returned to Kwikee's' factory.

Kwikee will pay for the labor required to repair or replace its products on claims submitted within 2

years of the date of purchase. The warranty on repaired or replaced parts shall be limited to the

unexpired duration of the original warranty.

This warranty does not apply to products or parts that, in Kwikee’s opinion, have been subject to

abuse, accident, alteration, improper installation/repair, inadequate maintenance or deterioration due to

normal wear. This warranty does not apply to electrical wiring or hydraulic hoses. The purchaser shall

pay all shipping or other transportation charges for any warranty claim.

Kwikee makes no warranty (and disclaims any implied warranty) regarding the merchantability, fitness

for a particular purpose or the suitability of this product for use with other products. In no event shall

Kwikee be liable for incidental, consequential or property damage arising from the purchase and/or use

of this product or any claim hereunder. This warranty is in lieu of all other express and implied

warranties. Kwikee neither assumes nor authorizes any other person to assume any liability for

warranty claims not provided herein.

This warranty gives you specific legal rights including other rights that may vary from state to state.

Some states do not allow limitations on implied warranties and exclusion or limitation of incidental or

consequential damages, therefore the limitations and exclusions contained herein may not apply to you.

Any questions regarding warranty claims should be directed to your dealer or contact Kwikee Products

Company. Address correspondence to: Kwikee Customer Service Representative, 230 Davidson Ave.,

Cottage Grove, Oregon 97424; or contact us by telephone at 1-800-736-9961.

Limited Warranty

I M P O R T A N T

Please take a minute to fill in the

enclosed Level Best Warranty

Registration.

Send the completed registration

form to:

Kwikee Products

230 Davidson Ave.

Cottage Grove, OR 97424

Andere Handbücher für level best 2000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kwikee Hebesystem Handbücher

Kwikee

Kwikee level best 2000 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung