Kwikset Powerbolt 2 Bedienungsanleitung

START

First, we need to confirm your lock is “ready” to

be programmed.

To be sure, let’s reset your lock.

1. Make sure the lock is in the unlocked position.

2. Remove the battery cover.

3. Press and hold the “Reset” button for 5 seconds. You will hear 3 long beeps after

the 5 seconds is completed indicating the lock has been reset.

A User Code is used to unlock the door while a Mastercode is a password for making changes to

the lock features.

Step 1:

Reset your lock to original settings

Interior of door

You will reset your User Code to 1-2-3-4

and Mastercode to 0-0-0-0 when the reset is

complete.

TIP

Powerbolt 2| Touchpad Keyless Entry

Programming Instructions

Programming Instructions Powerbolt 2 Touchpad Keyless Entry

Step 2:

Set locking and unlocking direction

1. Make sure the door is open and in the unlocked position.

2. Press 0 –0 –0 –0 – – 00 –

Note: Each button represents two numbers (i.e. ONLY push the button once for 0). If

you incorrectly enter the code, wait 10 seconds until you hear three beeps. Then you

can try again.

You may or may not see your keypad light up

orange during this step. Either way, complete the

step.

TIP

3. If the step was completed correctly, the latch bolt will extend out and retract back in

completely.

The lock will also beep twice and the keypad will

flash Green when the step is successful.

TIP

Step 2:

Set locking and unlocking direction

Programming Instructions Powerbolt 2 Touchpad Keyless Entry

1. Make sure the door is open and in the unlocked position.

2. Press 0

3. The latch will extend fully to the lock position and end with one beep and the keypad

will turn off.

4. Enter 1 –2 –3 –4 –

5. The latch will retract fully in the unlock position and end with one beep and the

keypad will turn off.

1. Make sure the door is open and in the unlocked position.

2. Enter the default Master Code 0 –0 –0 –0 – – 5 –

3. The lock will beep twice and the keypad will flash Green.

Step 3:

Test the Lock

Step 4:

Delete all User Codes

Programming Instructions Powerbolt 2 Touchpad Keyless Entry

1. Make sure the door is open and in the unlocked position.

2. Enter the default Master Code 0 –0 –0 –0 – – 7 –

3. Enter a 4 to 10 digit code and press

4. The lock will beep twice and the keypad will flash Green

If you need further assistance, please call us back at 1-800-327-LOCK (5625).

1. Make sure the door is open and in the unlocked position.

2. Enter the default Master Code 0 –0 –0 –0 – – 1 –

3. Enter a 4 to 10 digit code and press

4. The lock will beep twice and the keypad will flash Green.

Step 6:

Change the Default Mastercode

Step 5:

Program User Codes

Andere Handbücher für Powerbolt 2

Inhaltsverzeichnis

Andere Kwikset Gegensprechanlage Handbücher

Kwikset

Kwikset Smartcode series Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung

LG L5142 Bedienungsanleitung