Kyocera Mita FS-1800N+ Bedienungsanleitung
For the Kyocera Mita Page Printers
Für Kyocera Mita Seitendrucker
Pour imprimantes de page Kyocera Mita
Per la stampanti Kyocera Mita
Para la impresora de páginas Kyocera Mita
User's Manual
Bedienungsanleitung
Manuel d'utilisation
Istruzioni per l'uso
Manual del usario
Bulk Paper Feeder
Papierzuführung
Chargeur de papier
Alimentatore carta
Alimentador de papel
PF8-cvr.pm6 12/19/00, 8:21 PM1
PF8-cvr.pm6 12/19/00, 8:21 PM2
1
English
Note on Paper
Before purchasing paper, test a sample on the printer installed with
the paper feeder and check that printing quality is satisfactory.
Notice
We shall have no liability or responsibility to customers or any other
person or entity with respect to any liability, loss or damage caused or
alleged to be caused directly or indirectly by equipment sold or
furnished by us, including but not limited to, any interruption of
service, loss of business or anticipatory profits, or consequential
damages resulting from the use or operation of the equipment or
software.
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY
IMPROPER INSTALLATION.
The information in this manual is subject to change without
notification. Additional pages may be inserted in future editions. The
user is asked to excuse any technical inaccuracies or typographical
errors in the present edition.
No responsibility is assumed if accidents occur while the user is
following the instructions in this manual.
The contents of this manual are protected by copyright. No part of this
manual may be reproduced or copied by any means without the
permission of the copyright holder.
pf8-Eng.pm6 12/19/00, 8:21 PM1
2
Radio interference requirement in European countries
The option bulk paper feeder PF-8E is intended for use with the printer models FS-1800,
FS-1800N, FS-3800, and FS-3800N which are type tested and categorized as a Class B
computing devices in accordance with the EN55022 rules.
Device in the Class B category may cause interference to radio or television reception
particularly in a residential installation.
Information to users:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
❐Reorient or relocate the receiving antenna.
❐Increase the separation between the equipment and receiver.
❐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
❐Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer for compliance could void the
user’s authority to operate the equipment.
Table of contents
Introduction ............................................................................................3
Packing List .....................................................................................4
Setup .........................................................................................................4
Choosing a Location ........................................................................4
Installation ..............................................................................................5
Removing the MP Tray ...................................................................5
Installing the Base and the Printer................................................7
Installing the Bulk Paper Feeder ...................................................8
Operating the Optional Bulk Paper Feeder ................................. 10
Loading Paper................................................................................10
Cleaning Paper Jam ........................................................................... 13
Specifications....................................................................................... 14
pf8-Eng.pm6 12/19/00, 8:21 PM2
3
English
Introduction
The PF-8E is a bulk paper feeder for Kyocera Mita page printers. By
removing the MP tray and attaching the bulk paper feeder to the front
of the printer, you can continuously print on up to approximately 2,000
sheets of paper (at paper thickness of 0.1 mm). At the same time, you
can still select the printer’s normal paper cassette for the alternative
paper source. The bulk paper feeder is shipped with a base that
provides mounting for both the printer and the paper feeder. You can
select the source of paper supply yourself using the printer’s operator
panel or the printer driver.
Before using the optional bulk paper feeder, please read this manual,
then carefully follow all instructions given for installing and using the
optional paper feeder.
Printer
Paper Feeder
(PF-8E)
Base PB-60
(Option)
pf8-Eng.pm6 12/19/00, 8:21 PM3
4
Packing List
Make sure that the optional bulk paper feeder package contains each of
the following items in the indicated quantities.
❐PF-8E optional bulk paper feeder, 1
❐User’s Manual (this booklet), 1
Setup
The PF-8E is set up by placing itself and the printer on the base
(option), removing the printer’s MP tray and attaching the bulk paper
feeder to the front of the printer. Power for the paper feeder is supplied
directly from the printer through connectors on the base.
Before installing (or removing) the optional bulk
paper feeder, be sure to turn off the printer’s power.
Choosing a Location
The feeder will work best if it is installed in a location that is:
❐Level and well-supported: Place the base on a sturdy table or
desk.
❐Not exposed to sunlight or other bright light (not next to an
uncurtained window).
❐Well ventilated, not too hot or cold, and not too damp or dry:
Temperature should be 10 to 32.5 °C, ideally about 23 °C (50 to
90 °F, ideally about 68 °F). Humidity should be 20 to 80%,
ideally 60%.
pf8-Eng.pm6 12/19/00, 8:21 PM4
5
English
Installation
Removing the MPTray
Before installing the bulk paper feeder, remove the MP tray from the
front of the printer. The procedure is as follows.
The printer’s MP tray cannot be used together with
the optional bulk feeder.
1. Pull the printer’s paper feed unit release lever, then draw the
paper feed unit fully out of the printer.
2. Gently tilt the MP tray toward the printer until that it rests on
its side as shown in the figure.
Paper Feed Unit
Release Lever
Paper Feed Unit
MPTray
pf8-Eng.pm6 12/19/00, 8:21 PM5
6
3. Remove the MP tray from the printer by lifting it straight
upward.
4. After removing the MP tray, return the paper feed unit to its
original position.
pf8-Eng.pm6 12/19/00, 8:21 PM6
7
English
Installing the Base and the Printer
The printer is mounted on the upper deck of the base. See figure below.
1. Place the base onto a firm, sturdy table or desk.
The table or desk must be larger than the base.
2. Align the positioning pins on the top of the base with the holes
in the base of the printer, then slowly and carefully lower the
printer onto the base. You can easily set the printer on the
base by aligning the back edge of the printer with the end of
the base. Make sure that the connector on the base fits
squarely into the corresponding connector in the base of the
printer. See figure below.
Printer
Positioning Pins
Lower Deck for
the Feeder
Base
Connector
Upper Deck
pf8-Eng.pm6 12/19/00, 8:21 PM7
8
Installing the Bulk Paper Feeder
Mount the bulk paper feeder onto the rail in the lower deck of the base.
The rail is movable and must be pulled out before installing the bulk
paper feeder.
1. Pull the rail fully out until it stops. See figure below.
2. Grasp the feeder by the two handles in the side covers.
3. Facing the paper output slot of the feeder toward the printer,
align the (four) positioning tabs on the rail of the base with the
holes in the base of the feeder. Then slowly and carefully lower
the feeder onto the base.
Ensure that the arrow marks on the rail are
correctly aligned with the arrow marks on the
front side of the feeder before proceeding.
Feeder
Rail
Connector
Printer
Arrow Marks
PF-8E
Rail
pf8-Eng.pm6 12/19/00, 8:21 PM8
Andere Handbücher für FS-1800N+
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Kyocera Mita Druckerzubehör Handbücher
