Kyocera FS-9100DN - B/W Laser Printer Bedienungsanleitung

Installation Guide







Caution

NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER’S EMULATION MODE. The printer is

factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures described in

the User’s Manual contained as an electronic file in the Kyocera Mita Digital Library CD-ROM supplied with the printer.

Notice

The information in this guide is subject to change without notification. Additional pages may be inserted in future edi-

tions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No responsi-

bility is assumed for defects in the printer’s firmware (contents of its read-only memory).

This guide, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer,

are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this guide, any copy-

rightable subject matter without the prior written consent of Kyocera Corporation is prohibited. Any copies made of all

or part of this guide, any copyrightable subject must contain the same copyright notice as the material from which the

copying is done.

Table of Contents

  

  

  

  

 

! "

# $

% &'(')*+,

$ #-#. 

, - 

Revision 1.1 August 2001





1 Installation Procedure

Remove the printer from the carton and Install it in the following order after transporting it to the

installation position.

Start







Unpack.





















2 Unpacking

Carefully remove the printer and other items from the box. Check that nothing is missing against

the list of shipped components below.

List of Shipped Components

Be sure that four or more people unpack and install the printer.

Be very careful as the printer is heavy and can hunt your back.

Printer

Waste Toner Box

Toner Container

Installation Guide

(This booklet)

Kyocera Mita Digital Library

CD-ROM

Kyocera Mita Network Library

CD-ROM

Quick Configuration Guide

(for network interface)

Power Cord

(220 to 240 V models only)

Paper Size Plate (4)





Removing the Tapes

1Remove the tape holding the front cover.

2Remove the tape holding the MP (Multi

Purpose) tray.

3Remove the four tapes holding the paper

cassettes.

4Remove the tapes holding the left cover.

5Pull out the upper paper cassette and

remove the two tapes holding the bottom

plate.

6Pull out the lower paper cassette and

remove the two tapes holding the bottom

plate.

Paper Cassettes

MP Tray

Front

Cover

Left Cover 1

Paper Cassette





3 Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Environment

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

• Excessive dust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or make liberal

use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Low air pressure, e.g. elevations greater than 2000 meters (6500 feet) above sea level

Rear: 10 cm (3 - 15/16")

Left: 60 cm

(23 - 5/8")

Front: 100 cm (39 - 3/8")

Right: 70 cm

(27 - 9/16")

Be sure to secure enough

space around the printer.

Prolonged use without suffi-

cient clearance may cause

heat to build up within the

printer, resulting in fire.

Temperature 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

Do not install the printer where temperature or humidity is outside the recommended

range. Print quality may suffer and there will be an increased chance of paper jams.





4 Installing the Toner Container

Before you can use the printer for the first time, you must prepare it by installing the toner con-

tainer, waste toner box, and set up the interfacing with the computer.

1Open the printer front cover all the way.

2Take out the toner container.

3Tap the toner container on the top 5 to 6

times.

4Thoroughly shake the toner container (in

the directions of the arrows) ten times or

more to loosen and mix the toner inside.

5Grasp the handle on the toner container

and insert the toner container along the rail

of the printer.

Front Cover





6Hold the toner container by hands and fully

insert it into the printer.

Leave the front cover open for

next step

Installing the Waste

Toner Box





5 Installing the Waste Toner Box

The waste toner box is supplied with the printer.

1Install the waste toner box as shown in the

figure.

2Close the front cover.

6 Connecting the Printer to the Computer

There are various ways of connecting the printer to the computer, such as through the parallel

interface connector, serial interface connector, or through the network interface connector.

Printer Connections

A standard Centronics parallel interface ( ), serial (RS-232C) interface (IOIOI), and a 10/100

base-T connector are located on the right side of the printer.

Before performing this step, be sure to turn off both the printer and the computer’s

power switches and unplug the printer’s power plug from the power outlet. Failure

to do so may result in electrical shock.

Printer (Right Side)

Parallel Interface

Serial Interface

Network

Power cord





Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface connec-

tion on the rear side of the printer.

2Close the clips on both sides to fix the con-

nector in place.

Plug the other end of the printer cable into

the computer’s parallel interface connec-

tor.

Serial Interface Connection

1Plug one end of the printer cable (not

included) into the serial interface connec-

tion on the rear side of the printer.

2Securely tighten the screws on both sides

of the connector.

Plug the other end of the printer cable into

the computer’s serial interface connection.

Network Interface Connection

Plug the network cable (not included) into the

network interface connection on the right side

of the printer.

• Use a parallel printer cable that

complies with the IEEE1284

standards.

• The printer will work best if it is

installed near the computer. The

cable should be shielded and

not be longer than 3 meters (10

feet). Parallel Printer Cable

Serial Printer Cable

An Ethernet interface cable (straight

cable) is required to connect the

printer in network environment.

Network Cable



Andere Handbücher für FS-9100DN - B/W Laser Printer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kyocera Multifunktionsdrucker Handbücher

Kyocera

Kyocera ECOSYS M6026cidn Bedienungsanleitung

Kyocera

Kyocera Triumph-Adler 302ci Bedienungsanleitung

Kyocera

Kyocera FS-1025MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3051ci Produkthandbuch

Kyocera

Kyocera ECOSYS M2030dn/PN Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3510i Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3050ci Bedienungsanleitung

Kyocera

Kyocera Taskalfa Pro 15000c Bedienungsanleitung

Kyocera

Kyocera TASKalfa 650c Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C8520MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 2551ci Installations- und Betriebshandbuch

Kyocera

Kyocera KM-1620 Administratorhandbuch

Kyocera

Kyocera ECOSYS FS-C2126MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3010i Installations- und Betriebshandbuch

Kyocera

Kyocera FS-1028MFP DP Bedienungsanleitung

Kyocera

Kyocera 308ci Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-9130DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-4000DN Bedienungsanleitung

Kyocera

Kyocera 6003i Bedienungsanleitung

Kyocera

Kyocera KM-C4008 Bedienungsanleitung

Kyocera

Kyocera KM-5050 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 1801 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 181 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 2551ci Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung