Kyocera FS-9120DN Bedienungsanleitung

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

Caution on Installation

No liability is assumed for any damage caused by improper installation.

Notice on Software

Software used with this printer must support the printer’s emulation mode. The printer is factory-set to emulate

the HP PCL 6. The emulation mode can be changed by following the procedures described in the User’s Manual

contained as an electronic file in the Kyocera Mita Document Library CD-ROM supplied with the printer.

Notice on this Guide

The information in this guide is subject to change without notification. Additional pages may be inserted in

future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present

edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No

responsibility is assumed for defects in the printer’s firmware (contents of its read-only memory).

This guide, any copyrightable subject matter sold or provided with or in connection with the sale of the page

printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this

guide, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is pro-

hibited. Any copies made of all or part of this guide, any copyrightable subject must contain the same copyright

notice as the material from which the copying is done.

Table of Contents

1 Installation Procedure...................................................................................................1

2 Unpacking ......................................................................................................................2

3 Positioning the Printer..................................................................................................4

4 Installing the Toner Container .....................................................................................5

5 Installing the Waste Toner Box.....................................................................................7

6 Connecting the Printer to the Computer......................................................................7

7 Connecting the Power Cord ..........................................................................................9

8 Loading Paper in the Paper Cassettes and MP (Multi-Purpose) Tray .....................10

9 Turning the Power Switch On.....................................................................................16

10 Printing a Status Page ................................................................................................18

Revision 1.0 November 2003

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

1 Installation Procedure

Remove the printer from the carton and install it in the following order after transporting

it to the installation position.

Start

Install the waste toner box

Connect the printer to the computer

Install the toner container

Unpack

Remove the shipping tape

Position the printer

Turn the power switch on

Load paper in thepaper cassettes and

MP tray

Select a message language

Print a status page

Connect the power cord

End

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

2 Unpacking

Carefully remove the printer and other items from the box. Use the list of shipped compo-

nents below to make sure that all component are present.

Shipped Components

•Be sure that four or more people unpack and install the printer.

•Be very careful as the printer is heavy and can cause back injury if lifted incorrectly.

Printer

Waste Toner Box

Toner Container

Installation Guide

(This booklet)

CD-ROM’s

•Kyocera Mita Document Library

•Kyocera Mita Software Library

Quick Configuration Guide

(for network installation)

Power Cord

Paper Size Indicators (4)

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

Removing the Shipping Tape

1Remove the tape holding the front cover

in place.

2Remove the tape holding the MP (Multi

Purpose) tray in place.

3Remove the shipping tape holding the

paper cassettes in place.

4Remove the shipping tape holding the

left cover in place.

5Pull out the upper paper cassette and

remove the tape holding the bottom

plate.

6Pull out the lower paper cassette and

remove the tape holding the bottom plate

in place.

Paper Cassettes

MP Tray

Front

Cover

Left Cover 1

Paper Cassette

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

3 Positioning the Printer

Make sure that the printer location meets the following requirements:

Clearance

Environment

Places to Avoid

Avoid installing the printer in locations subject to:

•Direct drafts of hot or cold air

•Direct drafts from outside (Avoid locations near building entrances.)

•Sudden temperature or humidity changes

•Sources of high temperature for example near stoves or radiators

•Excessive dust

•Vibration

•Unstable surfaces and surfaces that are not level

•Ammonia or other harmful fumes (If you are planning to fumigate the room, or use a large

amount of insecticide, remove the printer first)

•Excessive sunlight or humidity

•Lack of ventilation

•Low air pressure, e.g. elevations greater than 2000 meters (6500 feet) above sea level

Rear: 10 cm (3 - 15/16")

Left: 60 cm

(23 - 5/8")

Front: 100 cm (39 - 3/8")

Right: 70 cm

(27 - 9/16")

Be sure to provide enough space

around the printer. Prolonged use

without sufficient clearance may

cause heat to build up inside the

printer, resulting in fire.

Temperature Humidity

10 to 32.5 °C (50 to 90.5 °F),

ideally about 23 °C (73.4 °F) 20 to 80 %, ideally 60 %

Do not install the printer in locations where temperature or humidity conditions exceed

the recommended range. Print quality may suffer and there will be an increased chance

of paper jams.

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

4 Installing the Toner Container

Before using the printer for the first time, you must prepare it by installing the toner con-

tainer, waste toner box, and set up the computer interface.

1Open the printer front cover all the way.

2Take out the toner container.

3Tap the toner container on the top 5 or 6

times.

4Thoroughly shake the toner container (in

the directions of the arrows) ten times or

more to loosen and mix the toner inside.

Front Cover

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

5Grasp the handle on the toner container

and insert the toner container along the

rail inside the printer. Be sure that the

gear side of the toner container faces the

printer.

6Hold the toner container using both

hands and fully insert it into the printer.

Gear Side

To the Printer

Leave the front cover open for next

step

Installing the Waste Toner

Box

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

5 Installing the Waste Toner Box

A waste toner box is supplied with the printer.

1Install the waste toner box as shown in

the figure.

2Close the front cover.

6 Connecting the Printer to the Computer

The printer can be connected to the computer in a number of ways: through the parallel

interface connector, through the USB (Universal Serial Bus) interface connector, or through

the network interface connector.

Printer Connections

The following standard interfaces are located on the right side of the printer: standard cen-

tronics parallel interface ( ), USB interface ( ), network (10base-T/100 base-TX) inter-

face ( ).

Before performing this step, be sure to turn off power to both the printer and the com-

puter and unplug the printer’s power plug from the power outlet. Failure to do so may

result in electrical shock.

Printer (Right Side)

USB Interface

Parallel Interface

Network Interface

Power Cord

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nection on the rear side of the printer.

2Close the clips on both sides to fix the con-

nector in place.

Plug the other end of the printer cable

into the computer’s parallel interface

connector.

USB (Universal Serial Bus) Interface Connection

1Plug one end of the USB cable (not

included) into the rear of the printer.

2Plug the other end of the USB cable into

the computer’s USB interface connector.

Network Interface Connection

Plug the network cable (not included) into

thenetworkinterfaceconnection on the right

side of the printer.

•Use a parallel printer cable that

complies with the IEEE1284

standards.

•For best results, install the

printerclose to the computer. The

cable should be shielded and be

no longer than 3 meters (10 feet). Parallel Printer Cable

•Use a cable that complies with

Revision 2.0 of USB standards (a

rectangular type A plug and a

square type B plug).

•The connecting cable should be

shielded and not be longer then 5

meters (16 feet).

USB Cable

An Ethernet interface cable (straight

cable) is required to connect the

printer to the network environment.

Network Cable

HUFPKPUVCNNDQQMࡍ࡯ࠫ㧞㧜㧜㧟ᐕ㧝㧝᦬㧝㧤ᣣޓἫᦐᣣޓඦᓟ㧟ᤨ㧝㧜ಽ

Andere Handbücher für FS-9120DN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kyocera Multifunktionsdrucker Handbücher

Kyocera

Kyocera KM-C4008 Bedienungsanleitung

Kyocera

Kyocera FS FS-1020D Bedienungsanleitung

Kyocera

Kyocera FS-2100DN Installations- und Betriebsanleitung

Kyocera

Kyocera FS-C2026MFP Bedienungsanleitung

Kyocera

Kyocera KM-3060 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 266ci Bedienungsanleitung

Kyocera

Kyocera KM-C2630D Bedienungsanleitung

Kyocera

Kyocera 1102H03NL0 Bedienungsanleitung

Kyocera

Kyocera ECOSYS P8060cdn Bedienungsanleitung

Kyocera

Kyocera KM-2530 Bedienungsanleitung

Kyocera

Kyocera KM-8030 Bedienungsanleitung

Kyocera

Kyocera FS-1128MFP Bedienungsanleitung

Kyocera

Kyocera FS-C1020MFP Bedienungsanleitung

Kyocera

Kyocera ECOSYS PA6000 Series Bedienungsanleitung

Kyocera

Kyocera TASKalfa 620 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 181 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3011i Bedienungsanleitung

Kyocera

Kyocera ECOSYS P6035cdn Bedienungsanleitung

Kyocera

Kyocera TASKalfa 205c Installations- und Betriebsanleitung

Kyocera

Kyocera TASKalfa 6501i Bedienungsanleitung

Kyocera

Kyocera FS-1100 null

Kyocera

Kyocera FS-C2026MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 180 Bedienungsanleitung

Kyocera

Kyocera FS FS-C8500DN Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung