Kyocera FS-600 Bedienungsanleitung

Kyocera Laser Printer FS-600

Installation Manual

This manual mainly covers topics pertaining to installation and maintenance of the

printer. The printer is also supplied with a CD-ROM and a Quick Reference

booklet. For other information such as operation, refer to the on-line User's Manual

in the CD-ROM and the Quick Reference booklet.

Introduction

Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software______________________________________________________________

SOFTWARE USED WITHTHIS PRINTER MUST SUPPORT THE PRINTER’S NATIVE MODE OR ONE OFITS EMULATION MODES. The printer

is factory set to emulate the HP LaserJet 5P. The emulation mode can be changed by following the procedures described in Chapter 2 of the User's

Manual (on CD-ROM).

Notice______________________________________________________________________

The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. The user is asked to

excuse any technical inaccuracies or typographical errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in

the printer’s firmware (contents of its read-only memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. All

rights are reserved. Copying or other reproduction of all or part of this manual, any copyrightable subject matter without the prior written consent of

Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as

the material from which the copying is done.

Regarding Tradenames ___________________________________________________________

PRESCRIBE is a registered trademark of Kyocera Corporation. PRESCRIBE II, PRESCRIBE IIe, KPDL 2, and KIR (Kyocera Image Refinement) are

trademarks of Kyocera Corporation.

Diablo 630 is a product of Xerox Corporation. IBM Proprinter X24E is a product of International Business Machines Corporation. Epson LQ-850 is a

product of Seiko Epson Corporation. HP LaserJet 5P is a product of Hewlett-Packard Company. Hewlett-Packard, PCL, and PJL are registered

trademarks of Hewlett-Packard Company. Centronics is a trade name of Centronics Data Computer Corp. PostScript is a registered trademark of

Adobe Systems Incorporated. Macintosh is a registered trademark of Apple computer, Inc. AppleTalk is a trademark of Apple Computer, Inc.

Microsoft, Windows, and MS-DOS are registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks of Adobe Systems

Incorporated which may be registered in certain jurisdictions.

This Kyocera page printer uses PeerlessPrint5 to provide the HP LaserJet compatible PCL5 language emulation. PeerlessPrint5 is a trademark of

The Peerless Group, Redondo Beach, CA 90278, U.S.A.

This product was developed using the TornadoTM Real Time Operating System and Tools from Wind River Systems.

Introduction

IBM PROGRAM LICENSE AGREEMENT _________________________________________________

THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG TO

INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER

WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS

LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND. IF

YOU DO NOT SO RETURN THE DEVICE WITHIN THE 14 DAYS, THEN YOU WILL BE ASSUMED TO HAVE AGREED TO THESE TERMS AND

CONDITIONS.

The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the country where

you acquired the Programs. You obtain no rights other than those granted you under this license.

The term “Programs” means the original and all whole or partial copies of it, including modified copies or portions merged into other programs. IBM

retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.

1. License

Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs and the

device to another party.

If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is then terminated.

The other party agrees to these terms and conditions by its first use of the Program.

You may not:

1) use, copy, modify, merge, or transfer copies of the Program except as provided in this license;

2) reverse assemble or reverse compile the Program; or

3) sublicense, rent, lease, or assign the Program.

2. Limited Warranty

The Programs are provided “AS IS.”

THERE ARE NO OTHER WARRANTIES COVERING THE PROGRAMS (OR CONDITIONS), EXPRESS OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

SUPPLEMENT TO AGREEMENT FOR SOFTWARE BUNDLING AND DISTRIBUTION FOR ALDC

3. Limitation of Remedies

IBM’s entire liability under this license is the following;

1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM’s liability will be for actual damages only and

will be limited to the greater of:

a) the equivalent of U.S.$25,000 in your local currency; or

b) IBM’s then generally available license fee for the Program

This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable.

Introduction

iii

IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if IBM, or its

authorized supplier, has been advised of the possibility of such damages. IBM will not be liable for any damages claimed by you based on any third

party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. IBM’s and the developer’s limitations of remedies

are not cumulative. Such developer is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions, so they

may not apply to you.

4. General

You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this license. In either

event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including personal property taxes, resulting

from this license. Neither party may bring an action, regardless of form, more than two years after the cause of action arose. If you acquired the

Program in the United States, this license is governed by the laws of the State of New York. If you acquired the Program in Canada, this license is

governed by the laws of the Province of Ontario. Otherwise, this license is governed by the laws of the country in which you acquired the Program.

Introduction

Typeface Trademark Acknowledgement _________________________________________________

All resident fonts in this printer are licensed from Bitstream Inc., Cambridge, Massachusetts, U.S.A.

Dutch801, Swiss742, Incised901, ZapfCalligraphic801, ZapfHumanist601, OriginalGaramond, and Chianti are trademarks of Bitstream Inc.

Centutry Schoolbook, Stymie, and Cooper-Black are trademarks of Kingsley-ATF Type Corporation.

ITC ZapfDingbats, ITC Souvenir, ITC Benguiat, and ITC Bookman are registered trademarks of International Type-face Corporation.

Revue is a trademark of Esselte Pendaflex Corporation in the U.S., Letraset Canada Ltd. in Canada, and Esselte Letraset Ltd. elsewhere.

Bitstream Sublicense Agreement _____________________________________________________

FONTWARE/TrueDoc developed by BITSTREAM INC. is provided as part of this Printer by KYOCERA CORPORATION under license. KYOCERA,

as a Licensee of BITSTREAM, grants you, the Sublicensee, non-exclusive right to use FONTWARE/TrueDoc installed in this Printer, if you agree to

and at all times comply with the following items:

1. Ownership

As the Sublicensee, you own the Printer in which FONTWARE/TrueDoc is originally installed, but BITSTREAM retains title to and ownership in the

software program of FONTWARE/TrueDoc. The Sublicense is not a sale of the original software program of FONTWARE/TrueDoc or any portion or

copy of it.

2. Copy Restrictions

FONTWARE/TrueDoc is copyrighted. Unauthorized copying of FONTWARE/TrueDoc even if modified, merged, or included with other software, is

expressly forbidden. You may be held legally responsible for any copyright in-fringement.

3. Unauthorized Use

FONTWARE/TrueDoc may not be removed, disclosed and transferred to any third party for any length of time without the prior written consent of

KYOCERA or BITSTREAM. Also, you may not modify, adapt, translate, reverse engineer, decompile, or create derivative works based on

FONTWARE/TrueDoc.

4. Term

This agreement should remain in full force and effect forever thereby allowing the Sublicensee to use the FONTWARE/TrueDoc forever unless the

Sublicensee violates the terms of paragraphs 2. or 3. above. In the event of such violation, this agreement will terminate automatically without notice

from KYOCERA. Upon termination, you should destroy FONTWARE/TrueDoc and all copies of them, in part and in whole, including modified copies,

if any.

Introduction

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note______________________________________________________________________

This equipment has been tested andfound to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the manufacturer for compliance could void the

user’s authority to operate the equipment.

Shielded circular cable should be used for interfacing with the computer.

Caution to user

Any modification without prior permission may cause harmful interference.

If any modification/change is introduced to this equipment without prior permission, Kyocera as the

manufacturer cannot guarantee compliance with FCC rules.

Introduction

To use equipment which does not comply with FCC rules is prohibited.

The printer may be optionally installed with the following units:

Conforming to the Class B limits

• PK-Series KPDL 2 Upgrade Kit

• IB-10 Serial Interface Board Kit

• PF-16 Paper Feeder (250 sheets)

Interface connectors

Important note on the interface connectors

Be sure to turn off printer power before connecting or disconnecting an interface cable* to the printer.

For protection against static discharge which may be applied to the printer’s internal electronics through

the interface connector(s), keep any interface connector which is not in use capped using the protective

cap supplied.

* Use shielded interface cable.

Safety information

Laser safety

This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human

Services (DHHS) Radiation Performance Standard according to Radiation Control for Health and Safety

Act of 1968. This means that the printer does not produce hazardous laser radiation. Since radiation

emitted inside the printer is completely confined within protective housings and external covers, the

laser beam cannot escape from the printer during any phase of user operation.

Laser notice

This printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter for Class

I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements

of IEC 825.

Introduction

vii

CAUTION LASER RADIATION WHEN OPEN.

DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.

∗ Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

(U.S.A./Canada) (Europe/Asia)

Introduction

viii

CDRH regulations

The Center of Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration

implemented regulations for laser products on August 2, 1976. These regulations apply to laser products

manufactured after August 1, 1976. Compliance is mandatory for products marketed in the United

States. A label indicating compliance with the CDRH regulations must be attached to laser products

marketed in the United States.

Ozone concentration

The printers generate ozone gas (O3) which may concentrate in the place of installation and cause an

unpleasant smell. To minimize concentration of ozone gas to less than 0.1 ppm, we recommend you not

to install the printer in a confined area where ventilation is blocked.

Caution labels

Introduction

IMPORTANT SAFEGUARDS

1. Read all of these instructions and save these instructions for later use.

2. Unplug this product from the wall outlet before cleaning.

3. Do not use this product near water.

4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious

damage to the product.

5. Slots and openings in the cabinet and the back are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating, these openings must not be blocked or

covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other

similar surface. This product should never be placed near or over a radiator or heat register. This

product should not be placed in a built-in installation unless proper ventilation is provided.

6. This product is equipped with a 3-wire grounding type plug, a plug having a third (grounding) pin.

This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to

insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat

the purpose of the grounding-type plug.

7. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk

on the cord.

8. If an extension cord is used with this product, make sure that the total of the ampere ratings on the

products plugged into the extension cord do not exceed the extension cord ampere rating.

9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous

voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid

of any kind on the product.

Andere Handbücher für FS-600

Inhaltsverzeichnis

Andere Kyocera Drucker Handbücher

Kyocera

Kyocera ECOSYS FS-C5150DN Installations- und Betriebsanleitung

Kyocera

Kyocera MA2000w Bedienungsanleitung

Kyocera

Kyocera ECOSYS M8130cidn Bedienungsanleitung

Kyocera

Kyocera FS-C5015N Bedienungsanleitung

Kyocera

Kyocera C5020N - FS Color LED Printer Bedienungsanleitung

Kyocera

Kyocera KM-8530 Bedienungsanleitung

Kyocera

Kyocera MT-1 Bedienungsanleitung

Kyocera

Kyocera FS-7000+ Bedienungsanleitung

Kyocera

Kyocera Ecosys FS-1200 Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-1350DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C2126MFP Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Kyocera

Kyocera KM-6230 Handbuch

Kyocera

Kyocera ECOSYS PA4000cx Bedienungsanleitung

Kyocera

Kyocera FS-3040MFP Bedienungsanleitung

Kyocera

Kyocera FS-1300D Bedienungsanleitung

Kyocera

Kyocera TASKalfa 306cl Bedienungsanleitung

Kyocera

Kyocera FS-C5015N Bedienungsanleitung

Kyocera

Kyocera ECOSYS PA2100cwx Bedienungsanleitung

Kyocera

Kyocera FS-1120D Bedienungsanleitung

Kyocera

Kyocera TASKalfa PA4500ci Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C8600DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-6950DN Bedienungsanleitung

Kyocera

Kyocera FS-8000C Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung