Kyocera FS-6020 Bedienungsanleitung
$
Page Printer
Installation Guide
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER’S EMULATION MODE. The
printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures
described in the Operation Guide contained as an electronic file in the CD-ROM supplied with the printer.
Notice
The information in this manual is subject to change without notification. Additional pages may be inserted in
future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present
edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No
responsibility is assumed for defects in the printer’s firmware (contents of its read-only memory).
This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page
printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this
manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is pro-
hibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copy-
right notice as the material from which the copying is done.
Table of Contents
STEP 1 Unpacking.........................................................................1
STEP 2 Positioning the Printer .....................................................2
STEP 3 Installing the Toner Container .........................................3
STEP 4 Connecting the Printer to the Computer.........................6
STEP 5 Connecting to Power........................................................8
STEP 6 Adding Paper to the Paper Cassette and MP Tray .........9
STEP 7 Turning Power On...........................................................15
STEP 8 Printing a Status Page....................................................16
©2002 by KYOCERA MITA CORPORATION. All rights reserved
Revision 1.0 October 2002
1
Unpacking
Carefully remove the printer and other items from the box. Check that nothing is miss-
ing against the list of shipped components below.
List of Shipped Components
STEP
1
Printer
(A)
(B)
(C)
Printer
Power Cord (B)
Installation Guide
[this booklet] and
other printed matter
(C)
CD-ROM (C)
To n e r
Container (A)
2
Positioning the Printer
Make sure that the place of installation meets the following requirements:
Clearance
Be sure to secure enough space
around the printer. Prolonged
use without sufficient clearance
may cause heat to build up
within the printer, resulting in
fire.
Environment
Do not install the printer where temperature or humidity is outside the rec-
ommended range. Print quality may suffer and there will be an increased
chance of paper jams.
Places to Avoid
Avoid installing the printer in locations subject to:
• Direct drafts of hot or cold air
• Direct drafts from outside (Avoid locations near building entrances.)
• Sudden temperature or humidity changes
• Sources of high temperature, for example, near stoves or radiators
•Excessivedust
•Vibration
• Unstable surfaces and surfaces that are not level
• Ammonia or other harmful fumes (If you are planning to fumigate the room, or
make liberal use of insecticide, remove the printer first!)
• Excessive sunlight or humidity
• Lack of ventilation
• Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above
sea level
Te m p e r a tu r e 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)
Humidity 20 to 80 %, ideally 60 %
STEP
2
30 cm
25 cm
60 cm
30 cm
50 cm
3
Installing the Toner Container
Before you can use the printer for the first time, you must set up the printer by installing
the toner container and the interfacing with the computer.
1Open the printer top cover all the way.
2Confirm that the lock lever is in the
release (UNLOCK) position. If not, pull it
forward until it is in the release posi-
tion.
3Take the toner container from the bag.
4Thoroughly shake the toner container
(in the direction of the arrow) ten times
or more to loosen and mix the toner
inside.
5Carefully remove the protective seal.
STEP
3
To p C o v e r
Toner Container
10 times or
more
Protective Seal
4
6Install the toner container into the
printer.
7Push firmly on the top of the toner con-
tainer at the positions marked PUSH
HERE.
When the toner container fits into
place, it will lock with a clicking sound.
8Push the lock lever to the lock (LOCK)
position.
9Close the top cover.
5
To remove the toner container
Pull the lock lever #1 to the release
(UNLOCK) position, pull the lock lever
#2 to the right and gently lift the toner
container.
Lock Lever #2
Lock Lever #1
6
Connecting the Printer to the Computer
There are various ways of connectingthe printer to the computer, such as throughthe
parallel interface connector, through the USB (Universal Serial Bus) interface connec-
tor, through the option serial interface board kit (IB-11) or through the option network
interface card.
Printer Connections
Before performing this step, be sure to turn off both the printer and the com-
puter’s power switches and unplug the printer’s power plug from the power
outlet. Failure to do so may result in electrical shock.
The standard Centronics parallel interface connector ( ) and USB interface
connector ( ) are located on the rear of the printer.
STEP
4
Printer (Rear)
Parallel Interface
Network Option Network
Interface Card
(3.3 V DC)
Power Supply
USB Interface
Option Serial Interface
Board Kit (3.3 V DC)
7
Parallel Interface Connection
1Plug one end of the printer cable (not
included) into the parallel interface con-
nector on the rear of the printer.
• Use a parallel printer cable
that complies with the
IEEE1284 standards.
• The printer will work best if it
is installed near the computer.
The connecting cable should
be shielded and not be longer
than 3 meters (10 feet).
2Close the clips on both sides to fix the
connector in place.
Plug the other end of the printer cable
into the computer’s parallel interface
connector.
USB (Universal Serial Bus) Interface Connection
1Plug one end of the USB cable on the
rear of the printer.
•Useacablethatcomplies
with Full-Speed USB 2.0 stan-
dard (a rectangular Type A
plug and a square Type B
plug).
• The connecting cable should
be shielded and not be longer
than 5 meters (16 feet).
2Plug the other end of the USB cable into
the computer’s USB interface connec-
tor.
Clip
Clip
USB Cable
Parallel Printer
Cable
8
Connecting to Power
This section describes the procedure for connecting the power cord and various cau-
tions.
Notes on Power Supply
• Install the printer near an AC wall outlet, preferably one that can be used for
the printer alone.
• Only use this printer with the supply voltage indicated on the serial number
label attached to the printer’s rear panel.
• If an extension cord is used, the total length of the power cord plus extension
should be 5 meters (16 feet) or less.
Power Requirements
To Connect the Power Cord
• Be sure the printer’s power switch is turned off.
• Only use the power cord supplied with the printer.
1Plug the power cord into the power cord
connector on theear of the printer.
2Connect the other end of the power cord
into a power outlet.
Be sure to connect to a 3-wire
grounded power strip.
Voltage 220 to 240 V, ±10 %
Frequency 50/60 Hz (220 to 240V) ±2 %
Current capacity Max. 3.8 A at 220 to 240 V
STEPSTEP
5
Power Cord
Connector
Power Cord
Andere Handbücher für FS-6020
3
Inhaltsverzeichnis
Andere Kyocera Drucker Handbücher
Kyocera
Kyocera F-1000 Bedienungsanleitung
Kyocera
Kyocera FS-3750 - B/W Laser Printer Bedienungsanleitung
Kyocera
Kyocera FS-1800+ Bedienungsanleitung
Kyocera
Kyocera FS-1300D Bedienungsanleitung
Kyocera
Kyocera ECOSYS MA4000cifx Installations- und Betriebsanleitung
Kyocera
Kyocera ECOSYS P4140dn Bedienungsanleitung
Kyocera
Kyocera FS-2100DN Installations- und Betriebshandbuch
Kyocera
Kyocera MA2000w Bedienungsanleitung
Kyocera
Kyocera Ecosys FS-C5300DN Bedienungsanleitung
Kyocera
Kyocera ECOSYS FS-9130DN Bedienungsanleitung
Kyocera
Kyocera ecosys M2735DW Bedienungsanleitung
Kyocera
Kyocera FS-1300D Bedienungsanleitung
Kyocera
Kyocera C8100DN - Color Laser Printer Gebrauchs- und Pflegehandbuch
Kyocera
Kyocera FS-2000D Bedienungsanleitung
Kyocera
Kyocera ECOSYS M3145idn Bedienungsanleitung
Kyocera
Kyocera ECOSYS FS-6950DN Bedienungsanleitung
Kyocera
Kyocera FS 1100 - B/W Laser Printer Bedienungsanleitung
Kyocera
Kyocera 1102RX3NL0 Bedienungsanleitung
Kyocera
Kyocera FS-C5020N Bedienungsanleitung
Kyocera
Kyocera FS-2000D Betriebsanleitung
