Kyocera FS FS-1020D Bedienungsanleitung

FS-1020D

Page Printer

Installation Guide

Ifs1020ep-eng.book 1 ページ２００３年９月３日　水曜日　午後４時４７分

Caution

NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION

MODE. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by

following the procedures described in the Operation Guide contained as an electronic file in the

Kyocera Mita Document Library CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be

inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical

errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this

manual. No responsibility is assumed for defects in the printer's firmware (contents of its read-only

memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale

of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduc-

tion of all or part of this manual, any copyrightable subject matter without the prior written consent

of Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any

copyrightable subject must contain the same copyright notice as the material from which the copy-

ing is done.

Table of Contents

STEP 1 Unpacking .......................................................................1

STEP 2 Positioning the Printer....................................................3

STEP 3 Installing the Toner Container........................................4

STEP 4 Connecting the Printer to the Computer .......................7

STEP 5 Connecting the Power Cord...........................................9

STEP 6 Adding Paper to the Paper Cassette and MP Tray......10

STEP 7 Printing a Status Page..................................................17

Ifs1020ep-eng.book 1 ページ２００３年９月３日　水曜日　午後４時４７分

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is miss-

ing against the list of shipped components below.

List of Shipped Components

STEP

Printer

Power Cord (D)

Toner Container [TK-18] (B)

Installation Guide [this booklet] (A)

CD-ROMs (A)

Cleaning Cloth (A)

Printer

(C)

(B)

(D)

(A)

Extension Tray (C)

[for U.S.A. only]

Ifs1020ep-eng.book 1 ページ２００３年９月３日　水曜日　午後４時４７分

Removing Shipping Material

Remove the tape on the rear side of the printer, and remove the protective packing

from the paper cassette.

Ta p e

Protective Packing

Ifs1020ep-eng.book 2 ページ２００３年９月３日　水曜日　午後４時４７分

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Be sure to secure enough space

around the printer. Prolonged

use without sufficient clearance

may cause heat to build up

within the printer, resulting in

fire.

Environment

Do not install the printer where temperature or humidity is outside the rec-

ommended range. Print quality may suffer and there will be an increased

chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

•Excessivedust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or

make liberal use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above

sea level

Te m p e r a tu r e 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

STEP

30 cm (11-13/16 inches)

40 cm

(15-3/4

inches)

25 cm

(9-7/8

inches)

50 cm

(19-11/16

inches)

25 cm (9-7/8

inches)

Ifs1020ep-eng.book 3 ページ２００３年９月３日　水曜日　午後４時４７分

Installing the Toner Container

Before you can use the printer for the first time, you must set up the printer by installing

the toner container and interfacing with the computer.

1Open the printer top cover all the way.

2Confirm that the lock lever is in the

release (UNLOCK) position. If not, pull it

forward until it is in the release posi-

tion.

3Take the toner container from the bag.

Hold it with the protective seal (orange-

colored) facing up. Shake the toner con-

tainer horizontally at least 5 times. This

ensures that the toner is evenly distrib-

uted inside.

STEP

Ifs1020ep-eng.book 4 ページ２００３年９月３日　水曜日　午後４時４７分

4Carefully remove the protective seal.

5Install the toner container into the

printer.

6Push firmly on the top of the toner con-

tainer at the positions marked PUSH

HERE.

Ifs1020ep-eng.book 5 ページ２００３年９月３日　水曜日　午後４時４７分

7Push the lock lever to the lock (LOCK)

position.

8Close the top cover.

To remove the toner container

Pull the lock lever #1 to the release

(UNLOCK) position, pull the lock lever

#2, then gently remove the toner con-

tainer.

LOCK

UNLOCK

LOCK

UNLOCK

Lock Lever #2

Lock Lever #1

Ifs1020ep-eng.book 6 ページ２００３年９月３日　水曜日　午後４時４７分

Connecting the Printer to the Computer

There are various ways of connecting the printer to the computer, such as throughthe

parallel interface connector, through the USB (Universal Serial Bus) interface connec-

tor, through the optional serial interface board kit (IB-11) or through the optional net-

work interface board.

Printer Connections

Before performing this step, be sure to turn off both the printer and the com-

puter’s power switches and unplug the printer’s power plug from the power

outlet. Failure to do so may result in electrical shock.

The standard Centronics parallel interface connector and USB interface connec-

tor are located on the rear of the printer.

STEP

Printer (Rear)

Optional Serial Interface

Board kit (IB-11)

Parallel Interface

Network

Optional Network

Interface Board

(DC 3.3V)

Serial Interface

Power Supply

USB

Interface

Ifs1020ep-eng.book 7 ページ２００３年９月３日　水曜日　午後４時４７分

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nector on the rear of the printer.

• Use a parallel printer cable

that complies with the

IEEE1284 standards.

• The printer will work best if it

is installed near the computer.

The connecting cable should

be shielded and not be longer

than 3 meters (10 feet).

2Close the clips on both sides to fix the

connector in place.

Plug the other end of the printer cable

into the computer’s Centronics paral-

lel interface connector.

USB (Universal Serial Bus) Interface Connection

1Plug one end of the USB cable on the

rear of the printer.

•Useacablethatcomplies

with Revision 2.0 of USB stan-

dard (a rectangular Type A

plug and a square Type B

plug).

• The connecting cable should

be shielded and not be longer

than 5 meters (16 feet).

2Plug the other end of the USB cable into

the computer’s USB interface connec-

tor.

To p r i n t e r

Clips

Printer Cable

To p r i n t e r

USB Cable

Ifs1020ep-eng.book 8 ページ２００３年９月３日　水曜日　午後４時４７分

Andere Handbücher für FS FS-1020D

Inhaltsverzeichnis

Andere Kyocera Drucker Handbücher

Kyocera

Kyocera FS-C5100DN Bedienungsanleitung

Kyocera

Kyocera PA2000w Handbuch

Kyocera

Kyocera ECOSYS FS-1035MFP/DP Bedienungsanleitung

Kyocera

Kyocera FS-3750 - B/W Laser Printer Bedienungsanleitung

Kyocera

Kyocera TASKalfa MA3500ci Bedienungsanleitung

Kyocera

Kyocera KM-4230 Handbuch

Kyocera

Kyocera FS-1050 - B/W Laser Printer Bedienungsanleitung

Kyocera

Kyocera DP-1800 Installationshandbuch

Kyocera

Kyocera FS-820 Bedienungsanleitung

Kyocera

Kyocera ECOSYS P6235cdn Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-6525MFP Bedienungsanleitung

Kyocera

Kyocera Ecosys P2235dn Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3551ci Bedienungsanleitung

Kyocera

Kyocera FS-8000C Series Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C5150DN Bedienungsanleitung

Kyocera

Kyocera FS-820 Bedienungsanleitung

Kyocera

Kyocera FS-2020D Bedienungsanleitung

Kyocera

Kyocera FS-1030D Bedienungsanleitung

Kyocera

Kyocera FS-820 Bedienungsanleitung

Kyocera

Kyocera FS-820 Bedienungsanleitung

Kyocera

Kyocera FS-1714M Bedienungsanleitung

Kyocera

Kyocera Ecosys FS-3820N Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C8650DN Installations- und Betriebshandbuch

Kyocera

Kyocera ECOSYS FS-6525MFP Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung