Kzyee KM10 Montageanleitung

Table of Contents

Vehicle Super Probe

- 1 -

Table of

Contents

1. IMPORTANT SAFETY INFORMATION......................................................2

2. USING THE TEST TOOL ...........................................................................2

2.1 SPECIFICATIONS ............................................................................2

2.2 TOOL DESCRIPTION... ......................................................................3

2.3 PARTS LIST ........................................................................................4

2.4 GENERAL DESCRIPTION ................................................................4

2.5 POWER ..............................................................................................4

2.6 QUICK SELF-TEST ............................................................................4

2.7 AUTO CIRCUIT BREAKER ...............................................................5

2.8 WORK MODE. ....................................................................................6

3. OPERATING INSTRUCTIONS ............................................................7

3.1 VOLTAGE & POLARITY TESTING ....................................................7

3.2 CONTINUITY TESTING ....................................................................9

3.3 SIGNAL CIRCUIT TESTING .............................................................10

3.4 ACTIVATING COMPONENTS IN YOUR HAND ...............................10

3.5 ACTIVATING COMPONENTS IN THE VEHICLE..............................11

3.6 TESTING TRAILER LIGHTS AND CONNECTIONS.........................12

3.7 ACTIVATING COMPONENTS W/GROUND......................................13

3.8 RED/GREEN POLARITY LED.............................................................14

3.9 FOLLOWING & LOCATING SHORT CIRCUITS..................................14

3.10 CHECKING FOR BAD GROUND CONTACTS ..........................................15

4. TEST TOOL SPECIFICATIONS ………………….................................15

5. TEST TOOL KNOWLEDGE ..............................................................15

6. WARRANTY ................................................................................................17

Vehicle Super Probe

- 2 -

1. Important Safety Information

To prevent personal injury or damage to vehicles and/or the test tool, read this

instruction manual first and observe the following safety precautions at a minimum

whenever working on a vehicle:

◆Always perform automotive testing in a safe environment.

◆Wear safety eye protection that meets ANSI standards.

◆Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot

engine parts.

◆Operate the vehicle in a well ventilated work area: Exhaust gases are poisonous.

◆Put blocks in front of the drive wheels and never leave the vehicle unattended

while running tests.

Use extreme caution when working around the ignition coil, distributor cap, ignition

wires and spark plugs. These component create hazardous voltages when the

engine is running.

◆Put the transmission in PARK ( for automatic transmission) or NEUTRAL (for

manual transmission) and make sure the parking brake is engaged.

◆Keep a fire extinguisher suitable for gasoline/chemical/ electrical fires nearby.

◆Don’t connect or disconnect any test equipment while the ignition is on or the

engine is running.

◆Keep the tool dry, clean, free from oil/ water or grease. Use a mild detergent on a

clean cloth to clean the outside of the test tool, when necessary.

◆When the power switch in the tool is depressed battery current/voltage is

conducted directly to the tip which may cause sparks when contacting ground or

certain circuits. Therefore the tool should NOT be used around flammables such as

gasoline or its vapors. The spark of an energized tool could ignite these vapors. Use

the same caution as you would when using an arc welder.

2. Using the Test Tool

2.1 Specifications

Display

TFT color display (160x128 dpi )

Operating Temperature

0 to 60℃( 32 to 140℉)

Storage Temperature

-40 to 70℃(-40 to 185℉)

External Power

12.0 or 24.0 V power provided via vehicle battery

Dimensions (L*W*H)

178*47*28mm (7*1.85*1.10in )

Net Weight

0.1Kg (0.22LB)

Vehicle Super Probe

- 3 -

2.2 Tool Description

①Probe Tip - Contacts the circuit or component to be tested.

②Head Lights - Illuminates dark work areas or work areas at night.

③Red/ Green Polarity Indicator - Identifies positive, negative or open circuits. The

RED Indicator lights when the Probe Tip is contacting a positive circuit. The GREEN

Indicator lights when the probe Tip is contacting a negative circuit.

④LCD Display - Indicates test results.

⑤Power Switch - Allows you to conduct a positive or negative battery current to the

tip for activating and testing the function of electrical components.

⑥Mode Button - Selects the work mode: AC voltage, DC voltage, resistance,

diode.

⑦Auxiliary Ground Lead - Assists test as a ground lead.

⑧Adaptor -Connects to the battery.

Vehicle Super Probe

- 4 -

2.3 Parts List

2.4 General Description

The tool is the best electrical tester for reducing diagnostic time in all 6 to 30-volt

vehicle electrical systems. After a simple hook-up of the tool to the vehicle’s battery,

you can:

◆Determine at a glance if a circuit is positive, negative, or open without having to

reconnect clips from one battery pole to another.

◆Test for continuity with its built-in auxiliary ground lead.

◆By depressing the power switch, conduct a positive or negative battery current to

the probe tip for testing the function of an electrical component without the use of

jumper wires.

◆Test for poor ground contacts instantly without performing voltage drop tests. The

tool is also short circuit protected; its internal circuit breaker will trip if it becomes

overloaded.

◆Follow and locate short circuits without wasting fuses. The tool’s long cable allows

you to test along the entire length of the vehicle without constantly searching for

suitable vehicle grounds.

2.5 Power

The tool is powered via the vehicle battery. Connect the RED battery clamp to the

POSITIVE terminal of the vehicle’s battery, and the BLACK clamp to the NEGATIVE

terminal. When the tool is first connected to a battery (power source), it will sound a

beep and the Head Lights will be on to illuminate the test area of the probe tip.

2.6 Quick Self-Test

Before you test a circuit or component, be sure your tool is in good order by doing a

quick self-test.

With the tool connected, perform a quick self-test. The power switch is a momentary

rocker switch located on the tool’s body. Flanking the switch are positive and negative

Part

Description

Qty

User’s Manual

Cigarette lighter adapter

Battery hookup clips

Probe tip

Extension cable (20ft.)

Rugged blow molded case

Power assist cable

Vehicle Super Probe

- 5 -

markings.

Press the Power Switch forward to activate the tip with a positive voltage. The Red

LED should light and LCD display will read the battery voltage. A beep tone will sound.

Let go of the power switch and the LED will turn off and the tone will cease.

Press the Power Switch rearward to activate the tip with a negative voltage. The

Green LED should light and the LCD display will read the 0.0V (ground). A beep tone

will sound. Let go of the power switch and the LED will turn off and the tone will cease.

Your tool is working correctly and is now ready for use. ( Figure 1)

Figure 1

IMPORTANT: When powering-up components, you can increase the life of

power switch in the tool if you first press the switch, then contact the tip to the

component. The arcing will take place at the tip instead of the contacts of the switch.

2.7 Auto Circuit Breaker

The tool is short-circuit protected. Its internal circuit breaker will trip if it becomes

overload. The circuit breaker is a valuable test tool as well as a safety measure to

protect the tool from overload.

When circuit breaker tripped, all other functions of the tool are still active, which

means you can still probe a circuit and observe the voltage reading. When the circuit

Vehicle Super Probe

- 6 -

breaker is tripped, the tool will NOT be able to conduct battery current to the tip even

when the power switch is pressed. Intentionally tripping the breaker and using the

tool to probe can be considered an added precaution against accidental pressing of

the power switch.

2.8 Work mode

There are four modes to diagnose the electrical systems, which can be accessed by

depressing the Mode Button and cycling through each one.

DC voltage

While the tool in this mode, contact the probe tip to a circuit, then the LCD display will

read the DC voltage with a resolution of 0.1 volt. (Figure 2)

Figure 2

AC voltage

While the tool in this mode, contact the probe tip to a circuit, then the LCD display will

read the Max. voltage, the Min. Voltage and frequency (Figure 3).

Figure 3

Resistance

While the tool in this mode, contact the probe tip to a circuit, then the LCD display will

read the resistance between the tip and auxiliary ground lead. (Figure 4)

Vehicle Super Probe

- 7 -

Figure 4

Diode

In this mode, the probe tip contact the positive terminal of the diode, connect the

auxiliary ground lead to the negative terminal of the diode, the screen will display the

forward voltage drop, indicates the forward bias. If exchange the probe tip and

auxiliary ground lead, the screen will not display the voltage, indicates the reverse

bias.

Figure 5

3. Operating Instructions

3.1 Voltage & Polarity Testing

While the tool is in DC Voltage mode, contact the probe tip to a POSITIVE circuit. The

red LED will light and the LCD displays the voltage with a resolution of 0.1V. A beep

tone will sound.

If contact the probe tip to a NEGATIVE circuit, the green LED will light and the LCD

displays the voltage with a resolution of 0.1V. A beep tone will sound.

If contact the probe tip to an OPEN circuit, neither of the LED will light. (Figure 6)

Vehicle Super Probe

- 8 -

Figure 6

Figure 7

Vehicle Super Probe

- 9 -

3.2 Continuity Testing

While the tool is in Resistance mode, using the probe tip with chass is ground or the

auxiliary ground lead, continuity can be tested on wires and components attached or

disconnected from the vehicle’s electrical system.

When the probe tip is contacting a good ground, the LCD will indicate “0.0Ω” and

green LED will be on. A beep tone will sound (Figure 8).

Figure 8

In other cases, the LCD only indicates the resistance value. (Figure 9)

Figure 9

If the resistance value is greater than 100KΩ, the LCD will show “0L”.

Inhaltsverzeichnis

Andere Kzyee Prüfgeräte Handbücher

Kzyee

Kzyee KM50 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung