La Crosse Technology Radio Controlled Projection Alarm WT-5110 Bedienungsanleitung

WT-5110

433 MHz

Radio Controlled Projection Alarm

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

About WWVB 3

Quick Set-Up Guide 4

Detailed Set-Up Guide

Battery Installation 5

Program Mode

Programming Sequence 6

Function Buttons 6

Manual Time Setting 6

Time Zone Setting 6-7

Daylight Saving Time (DST) Setting 7

Features & Operations

Features 8

Radio-Controlled Time 8

Projection 8

LED Backlight 9

Indoor Temperature 9

Indoor Humidity 9

Time Alarm 9

Changing Display Mode 10

Maintenance & Care 10

Troubleshooting 10

Specifications 11

Warranty and Contact Information 12-13

INVENTORY OF CONTENTS

1) WT-5110 Alarm Clock

2) AC adapter/transformer

3) Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1) Two fresh 1.5V AA batteries (optional for projection alarm clock)

FEATURES OF PROJECTION ALARM

Operation of these features is in section III

1. Radio-controlled time

2. Projection of time

3. LED backlight

4. Display of indoor temperature/humidity or alarm time

5. Time alarm

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB

radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously

throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through

the internal antenna in the projection alarm. However, due to the nature of the Earth’s Ionosphere,

reception is very limited during daylight hours. The projection alarm will search for a signal every

night when reception is best.

The WWVB radio station receives the time data from the NIST Atomic clock in Boulder, Colorado. A

team of atomic physicists is continually measuring every second, of every day, to an accuracy of ten

billionths of a second per day. These physicists have created an international standard, measuring a

second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For more detail, visit

http://www.boulder.nist.gov/timefreq.htm. To listen to the NIST time, call (303)499-7111. This number

will connect you to an automated time, announced at the top of the minute in “Coordinated Universal

Time”, which is also known as Greenwich Mean Time (GMT). This time does not follow Daylight

Saving Time changes. After the top of the minute, a tone will sound for every second. It is possible

that your projection alarm may not be exactly on the second due to the variance in the quartz.

However, the clock will adjust the quartz timing over the course of several days to be very accurate;

under 0.10 seconds per day.

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. We recommend beginning the set-up procedure at night when the

WWVB signal is easiest to receive.

2. It is also highly recommended to set the projection alarm in a window

or other area free of interference in the area of your home that is

closest to Colorado (the source of the WWVB signal).

NOTE: The above steps are not required but can help the projection

alarm receive the signal faster.

3. Place the batteries into the projection alarm clock.

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

NOTE: It is important to not press any buttons after inserting batteries as

this will interrupt the WWVB search sequence.

In this time the display will show both the indoor temperature and humidity. If the

station does not display both indoor temperature and indoor humidity after the 15

minutes please retry the set up as stated above. After both indoor temperature

and indoor humidity are displayed for 15 minutes you can place your projection

alarm in your desired location.

To complete the set up of your temperature station after the 15 minutes have

passed please follow the steps beginning on page 6.

DETAILED SET-UP GUIDE

I. BATTERY INSTALLATION

A. PROJECTION ALARM

1. Remove the battery cover.

2. Observe the correct polarity, and install 2 AA batteries.

3. In addition or instead of inserting batteries, the AC adapter can be used. Simply plug

the adapter into the receptacle on the

underneath of the alarm clock and then plug

in adapter.

4. Replace the battery cover.

5. The projector will activate and remain on if

the alarm clock is plugged in. If only batteries

are used, the projector will only be activated

when a button is pressed. The projection is a

red light, not harmful under normal usage,

although care should be taken to not look

directly into the light.

Notes:

•After the batteries have been installed a tone will sound, and the LCD (Liquid

Crystal Display) will activate.

•The indoor temperature/humidity will be displayed. Also, the time will appear as

“-:--”.

•The WWVB search is automatically initiated, and a tower icon appears and

flashes with the time colon (no tower icon will appear if the WWVB is too weak to

be detected, and the time display will remain on “-:--”).

•While the WWVB search is being conducted various numbers will appear in the

time display.

•After 15 minutes, the projection alarm will either display the WWVB time, or

discontinue the search if the time is not found. If the search is cancelled “-:--” will

remain in the time LCD.

•The projection alarm will conduct a WWVB search every hour until the first signal

is found.

•Once the WWVB time is found, a search is automatically conducted nightly at

midnight.

•If the signal is found at midnight, the tower icon will remain, if not, another search

will take place every hour (until 6:00 am) until the signal is found successfully.

•If no signal is found during this period, the tower icon will not appear and the

clock will search again at 12:00 am the next night.

•The radio-controlled time receiver is located on the bottom side of the projection

alarm. When using the AC adaptor be sure to keep the adapter cord away from

the bottom side of the unit as if the wire is too close it can cause weakened

reception sensitivity.

AC adapter

receptacle

II. PROGRAM MODE

To enter the Program Mode hold down the “MODE/MIN” button for 3 seconds, until the time

flashes in the top of the display. The Program Mode Guide is laid out in a manner that allows

you to program each function separately, or you can follow the instructions entirely to program

the projection alarm. Complete programming is usually done for the initial set-up, and will

require you to skip step 1 and 2 of programming sections D and E. To exit the setting mode

simply wait approximately 10 seconds for the projection alarm to automatically return to normal

operation.

A. PROGRAMMING SEQUENCE

1. Manual Time Display

2. Time Zone Setting

3. Daylight Saving Time On/Off

B. FUNCTION BUTTONS

There are 3 function buttons located on the front of the projection alarm and one on the top.

The function buttons are labeled: AL/HOUR, light direction icon, MODE/MIN, and SNOOZE

(the top bar).

C. MANUAL TIME SETTING

1. Hold down the “MODE/MIN” button for 3 seconds, the time will flash in the Time LCD.

2. Press and release the “AL/HOUR” button to advance the hours and press and release

the “MODE/MIN” button to advance the minutes.

NOTE: “A.M.” or “P.M.” will be displayed to the left of the time to help identify the time.

3. Press and release the “SNOOZE” button to confirm the time setting and to advance to

DST (Daylight Saving Time) setting.

D. TIME ZONE SETTING

1. Hold down the “MODE/MIN” button for 3 seconds, the time will flash in the Time LCD.

2. Press and release the “SNOOZE” button to advance to the time zone selection.

3. In the indoor temperature/humidity section of the LCD the time zone will flash.

Mode Button (toggles between

indoor temp/hum and alarm

time. Also adjusts minutes in

time setting mode

Alarm Button (also adjusts

the hours in time setting

mode

)

Display Direction

4. Press and release the “MODE/MIN” button to select the appropriate time zone. There

are 24 time zones to choose from (based relative to the international time standard of

GMT (“Greenwich Mean Time).

NOTE: The U.S. time zones will show abbreviations as opposed to the numerical time

zone indicator. For example Eastern Time will display “ET” when the Eastern Time

Zone is selected

5. Press and release the “SET” button to confirm the time zone setting and to advance to

the DST (Daylight Saving Time) setting.

E. DST (DAYLIGHT SAVING TIME) SETTING

Note: The DST default is “On”, meaning that the WWVB will automatically change the time

according to Daylight Saving Time in the spring and fall. For areas that do not recognize

DST changes (Arizona and parts of Indiana) turn the DST “OFF”.

1. Hold down the “MODE/MIN” button for 3 seconds, the time will flash in the Time LCD.

2. Press and release the “SNOOZE” button twice to advance to the DST setting.

3. “DST” will appear in the indoor temperature/humidity LCD and “ON” or “OFF” will flash

in the time LCD.

4. Press and release the “MODE/MIN” button to toggle between DST ON and OFF..

5. Press and release the “SNOOZE” button to confirm the DST setting and complete the

set-up sequence.

-4h Atlantic Time

-5h Eastern Time (default setting)

-6h Central Time

-7h Mountain Time

-8h Pacific Time

-9h Alaskan Time

-10h Hawaiian Time

-11h, -12h Next two time zones West of HAW

0h Greenwich Mean Time

-1h, -2h, -3h Three time zones West of GMT

III. FEATURES & OPERATIONS

A. FEATURES

1. Radio-controlled time

2. Projection of time

3. LED backlight

4. Display of indoor temperature/humidity or alarm time

5. Time alarm

B. RADIO-CONTROLLED TIME

1. The projection alarm will automatically search for the time signal upon initial set-up

and every night.

2. When the signal is being received, there will be a “tower” icon flashing to the left of the

time display.

3. When the time signal has been received successfully, the tower icon will remain

steady until midnight.

4. The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal can

be received up to 2,000 miles away through the internal antenna in the projection

alarm.

5. Due to the nature of the Earth’s Ionosphere, reception is very limited during daylight

hours. The projection alarm will search for a signal every night when reception is best.

6. The WWVB radio station receives the time data from the NIST Atomic clock in

Boulder, Colorado. A team of atomic physicists is continually measuring every

second, of every day, to an accuracy of ten billionths of a second per day. These

physicists have created an international standard, measuring a second as

9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

7. For more detail, visit http://www.boulder.nist.gov/timefreq.htm. To listen to the NIST

time, call (303) 499-7111. This number will connect you to an automated time,

announced at the top of the minute in “Coordinated Universal Time”, which is also

known as Greenwich Mean Time (GMT). This time does not follow Daylight Saving

Time changes. After the top of the minute, a tone will sound for every second.

8. It is possible that your projection alarm may not be exactly on the second due to the

variance in the quartz. However, the clock will adjust the quartz timing over the course

of several days to be very accurate; under 0.10 seconds per day.

C. PROJECTION OF TIME

1. When plugged into an AC outlet, the projection alarm can continuously project the

time.

2. When operating on batteries alone, the projection alarm will only project when the

snooze button is pressed or the alarm is sounding.

3. The projection will auto-focus for display from three to six feet away. A dark

surrounding will be necessary to clearly see the projection.

4. The direction of the display can also be rotated 360°in 90°increments by pressing the

directional button. There is no display on the LCD that signifies the direction.

5. The projector case can be rotated 180°to further help orient the projected display.

D. LED BACKLIGHT

1. The projection alarm has an LED backlight designed for night-viewing. This will light

up for 4 seconds whenever the snooze button is pressed.

2. The LED backlight cannot be turned on constantly; this would drain the batteries.

E. INDOOR TEMPERATURE

1. The projection alarm measures indoor temperature with an internal sensor.

2. This temperature is displayed in °F.

3. The indoor temperature will take time to adjust to the surrounding temperature as the

sensor is inside the case.

F. INDOOR HUMIDITY

1. The projection alarm measures indoor humidity with an internal sensor.

2. This humidity is displayed as a percentage (%).

3. The indoor humidity will take time to adjust to the surrounding humidity as the sensor

is inside the case.

G. TIME ALARM

1. SETTING THE ALARM

a. Press and hold “AL/HOUR” button for three seconds until the alarm time is

flashing.

b. Press and release “AL/HOUR” to advance the hour, and “MODE/MIN” to

advance the minute. The time will display “PM” if set to PM, and nothing if set to

AM.

c. The projection alarm will revert to normal operation when no buttons are pressed

for 15 seconds. The alarm is now set and activated.

2. ACTIVATING/DEACTIVATING THE

ALARM

a. After entering the alarm setting

mode, the alarm is activated.

b. To toggle between activating

and deactivating the alarm,

press the “AL/HOUR” button

briefly. “(((○)))”will be displayed

above the time display when the

alarm is activated.

3. TURNING ALARM OFF (WHILE

SOUNDING)

a. While the alarm is sounding, press and release the “SNOOZE” bar to disable the

alarm for 10 minutes.

b. After the SNOOZE bar is pressed the alarm icon will flash.

c. To disable the alarm for 24 hours, press and release any button other than

SNOOZE or display direction buttons.

NOTE: The alarm will sound for 84 seconds if the “SNOOZE” button is not pressed.

The alarm speeds up twice, once after 20 seconds and again after 50 seconds.

H. CHANGING DISPLAY MODE (INDOOR TEMPERATURE/HUMIDITY OR ALARM TIME)

There are two possible display modes in the indoor temperature/humidity section of the LCD

(lower left); indoor temperature and humidity or alarm time. To change the display press and

release the “MODE/MIN” button to toggle between the two modes.

IV. MAINTENANCE & CARE

A. Extreme temperatures, vibrations, and shock should be avoided to prevent damage to the

units.

B. Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents—

they may mark and damage the displays and casings.

C. Do not submerge in water.

D. Immediately remove all low powered batteries to avoid leakage and damage.

E. Replace with new batteries only, and of recommended size.

F. Opening the casings invalidates the warranty. Do not try to repair the units. Contact

La Crosse Technology for Repairs.

TROUBLESHOOTING

Problem: The Projection is faint

Solution: 1) Use AC adapter

2) Darken surroundings

3) Use fresh batteries (if AC is not used)

Problem: The LCD is faint.

Solution: Replace the batteries.

Problem: “OFL” appears in the indoor temperature LCD.

Solution: 1) Move unit to an area with warmer or cooler surrounding

temperature.

2) Current surrounding temperatures are outside measuring range.

Problem: No reception of WWVB signal.

Solution:

1) It may help reception to face the front of the projection alarm in the

general direction of Ft. Collins, Colorado.

2) Wait overnight for signal.

3) Be sure the projection alarm is at least 6 feet from any electrical

devices, i.e. TV sets, computers, or other radio controlled clocks.

4) Remove batteries for five minutes, reinsert and leave the unit alone

overnight without pressing buttons.

5) If problems persist contact La Crosse Technology.

Problem: Hour is incorrect (minute is correct).

Solution: Be sure correct time zone and daylight saving time are selected.

Problem: “--.-” appears in outdoor temperature LCD

Solution: 1) Check batteries in remote

2) If batteries are replaced in remote, the unit must be re-started.

Remove all batteries, and then follow start up procedure.

Note: For any questions not answered, contact La Crosse Technology with the contact information

found at the end of this instructional manual.

Inhaltsverzeichnis

Andere La Crosse Technology Uhr Handbücher

La Crosse Technology

La Crosse Technology WT-3128 Handbuch

La Crosse Technology

La Crosse Technology WS-6118AL-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-113 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 512-1422WH Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8001UM Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-8002U-B Abmessungen

La Crosse Technology

La Crosse Technology WT-3129S Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86279V3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3144S Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-5120 433 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8017U-MAH Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8007U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86279V4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3143H Handbuch

La Crosse Technology

La Crosse Technology S74870 Abmessungen

La Crosse Technology

La Crosse Technology 616-1410B Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-3840FL Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256-AL Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-1417H-AL Abmessungen

La Crosse Technology

La Crosse Technology WT-3181 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 102819 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616-1410 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3122A Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3129B Abmessungen

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

Sharp

Sharp SPC900 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung

LG LEC-005 Bedienungsanleitung

IKEA

IKEA ROTBLÖTA Bedienungsanleitung

U-Line

U-Line Н-2811 Bedienungsanleitung

Digiview

Digiview RC305EL Bedienungsanleitung